Chief CM2C40U Bedienungsanleitung

Chief Flat panel steun CM2C40U

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Chief CM2C40U (76 Seiten) in der Kategorie Flat panel steun. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/76

CM2C40 Installation Instructions

Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and

complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for

every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change

without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained

herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

IMPORTANT WARNINGS AND CAUTIONS!

The Alert messages DANGER, WARNING, CAUTION, IMPORTANT, and NOTE are used throughout these instructions and on the

product to alert the reader and/or operator of the existence of dangerous situations, conditions and/or important operational and

maintenance information.

"SAVE THESE INSTRUCTIONS"

WARNING: WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.

CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the

corresponding instructions.

WARNING: FAILURE TO READ AND FOLLOW THE FOLLOWING INSTRUCTIONS CAN RESULT IN SERIOUS PERSONAL

INJURY, DAMAGE TO EQUIPMENT OR VOIDING OF FACTORY WARRANTY. It is the installer’s responsibility to make sure all

components are properly assembled and installed using the instructions provided. Read all instructions before using this

furnishing.

DANGER: TO REDUCE THE RISK OF ELECTRIC SHOCK:

• ALWAYS unplug this furnishing from the electrical outlet before cleaning.

WARNING: TO REDUCE THE RISK OF BURNS, FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS:

• Unplug from outlet before putting on or taking off parts.

• Close supervision is necessary when this furnishing is being used by, or near, children, invalids, or disabled

persons.

• Use this furnishing only for its intended use as directed in these instructions. DO NOT use attachments not

recommended by the manufacturer.

• NEVER operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been

dropped or damaged, or dropped into water. Return the furnishing to a service center for examination and

repair.

• Keep the cord away from heated surfaces.

• NEVER operate the furnishing with the air openings blocked. Keep the air openings free of lint, and the like.

• NEVER drop or insert anything into any opening.

• DO NOT use outdoors.

• DO NOT operate where aerosol (spray) products are being used, or where oxygen is being administered.

• To disconnect, turn all controls to the off position, then remove plug from outlet.

WARNING: RISK OF ELECTRICAL SHOCK! Connect this device to a properly grounded outlet only.

CAUTION: ONE END OF POWER CORD MUST REMAIN ACCESSIBLE AT ALL TIMES! DO NOT block or impede access to

plug at any time!

CAUTION: Changes or modifications to this unit not expressly approved by the manufacturer can void the units FCC

compliance rating and make the unit illegal to operate.

Installation Instructions CM2C40

TOOLS REQUIRED FOR INSTALLATION

PARTS

CONTENTS

INSTALLATION REQUIREMENTS ..............................................................................................................6

Power Requirements and Wiring ................................................................................................................6

INSTALLATION ............................................................................................................................................6

Pre-Installation Configuration and Adjustments .........................................................................................6

Configuring the Mount for the Display .....................................................................................................6

Cable Installation and Routing ................................................................................................................8

Mount Installation ....................................................................................................................................11

Install Display .........................................................................................................................................12

Bottom Cover Installation ........................................................................................................................14

ADJUSTMENTS ............................................................................................................................................15

Bottom Cover Location Adjustment.............................................................................................................15

Lift Column Bearing Adjustment .................................................................................................................16

Extended Programming Capabilities .........................................................................................................17

IR-SE15 Programming ...............................................................................................................................18

Serial Communications ..............................................................................................................................19