Cecotec Bolero Aguazero 6500 FULL-BI C Bedienungsanleitung

Cecotec SpĆ¼lmaschine Bolero Aguazero 6500 FULL-BI C

Lesen Sie kostenlos die šŸ“– deutsche Bedienungsanleitung fĆ¼r Cecotec Bolero Aguazero 6500 FULL-BI C (12 Seiten) in der Kategorie SpĆ¼lmaschine. Dieser Bedienungsanleitung war fĆ¼r 18 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/12
1
VSWī˜Ÿ2VGAī˜ŸA ā€¢ User Guide
The Extron VSWī˜Ÿ2VGAī˜ŸA is a compact and economical two-input, one-output VGA
switcher with unbalanced stereo audio and 300 MHz (-3 dB) video bandwidth. It
accepts two VGA-UXGA, RGBHV, RGBS, RGsB, RsGsBs, component video, or
HDTV component video inputs. The switcher has two unbalanced stereo audio
inputs and one unbalanced stereo audio output. It also features a buffered local
monitor output for Input 1. A front panel toggle switch, a contact closure controller,
or the autoswitching option can be used for input selection.
This guide contains information about the Extron VSWī˜Ÿ2VGAī˜ŸA switcher. The
terms ā€œVSWī˜Ÿ2VGAī˜ŸAā€ and ā€œswitcherā€ are used interchangeably in this manual.
The Extron VSWī˜ŸIī˜ŸAAP interface, an optional accessory used when several
VSWī˜Ÿ2VGAī˜ŸA switchers are daisy chained together, is also discussed.
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to partī˜Ÿ15 of the
FCC rules. The Classī˜ŸA limits provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause interference. This interference must be corrected at the expense of the user.
NOTES:
ā€¢ This unit was tested with shielded ables on the peripheral devices. Shielded cables must be used to ensure I/O c
compliance with FCC emissions limits.
ā€¢ For more information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related
topics, see the on the Extron website.
Extron Safety and Regulatory Compliance Guide
Speciļ¬cations
Product specifications are available on the Extron website, www.extron.com.
Application Diagram
Up to 10 VSWī˜Ÿ2VGAī˜ŸA switchers can be daisy chained
together with each switcher input separately fed and
controlled by an optional accessory interface, the VSWī˜ŸIī˜ŸAAP.
Figure 1 is an example of how several such switcher-interface
combinations can be daisy chained together in a boardroom
environment.
By default, all switchers are set to input 2 as the active input.
Therefore, in a daisy chain of switchers the VGA and audio
signals ī˜žow from one switcher to input 2 of the next switcher
in the chain. The switchers are daisy chained in this fashion
until the last switcher in the daisy chain outputs to a projector
and audio ampliī˜er.
Up to ten switchers can be daisy chained together without
any degradation in picture quality. One power supply powers
up to ī˜ve switchers.
COMPUTER
SH MEOWAUDIO
VSW I AAP
In 1
In 2
Extron pre-made VGA with audio cable assemblies.
Expandable, economical presentation chain rfo
conference rooms and library study omro s.
Out In 2
VSW I AAP
VSW 2VGA A
Extron
VSW 2VGA A
VGA Switcher
In 1
Out In 2
VSW 2VGA A
In 1
Out
VSW 2VGA A
VSW I AAP VSW I AAP
Ext nro
VSW I AAP Projector
Projector
Extron
VSW I AAP
Figure 1. Daisy Chaining the Multiple Switchers
2
VSWī˜Ÿ2VGAī˜ŸA ā€¢ User Guide (Continued)
Features
ā€¢ Inputs ā€” Video on female 15-pin HD connectors, audio on 3.5 mm stereo mini jacks
ā€¢ Outputs ā€” Video on female 15-pin HD connectors, audio on 3.5 mm stereo mini jacks
ā€¢ 300 MHz (-3 dB) RGB video bandwidth
ā€¢ Compatible with VGA-QXGA and HDTV component video signals
ā€¢ Buffered loop-through for input one
ā€¢ ID bits from inputs 1 and 2 are routed to the output
ā€¢ Auto-input switching ā€” Automatically switches to the highest-numbered input with an active video signal.
ā€¢ Contact closure remote control
ā€¢ Front panel toggle switch for input selection
ā€¢ Through-desk, under-desk, and projector-mountable
ā€¢ 1U, quarter rack width metal enclosure
ā€¢ External Extron Everlast power supply included ā€” Provides worldwide power compatibility with high-demonstrated
reliability and low power consumption
ā€¢ Extron Everlast Power Supply is covered by a 7-year parts and labor warranty
Installation Overview
To install and set up the VSWī˜Ÿ2VGAī˜ŸA for operation, follow these steps:
1. Turn all of the equipment off. Make sure that the video and audio sources (computers, stereos, DVD players, or other
devices), the VSWī˜Ÿ2VGAī˜ŸA, the output devices (projectors, speakers), and the contact closure control device are all turned off
and disconnected from the power source.
2. If you are going to daisy chain two or more switchers with VSWī˜ŸIī˜ŸAAP control panels, identify the revision of the VSWī˜Ÿ2VGAī˜ŸA
board (for conī˜guring the VSWī˜ŸIī˜ŸAAPs) and conī˜gure the switcher jumpers (see on
Setting the VSWī˜Ÿ2VGAī˜ŸA Jumpers
pageī˜Ÿ4).
3. If desired, mount the switcher (see on pageī˜Ÿ9).Mounting the VSWī˜Ÿ2VGAī˜ŸA
4. Attach the cables (see Front Panel Features below and on the next page).Rear Panel Features
5. Connect power cords and turn on the devices in the following order: output devices, contact closure controller, VSWī˜Ÿ2VGAī˜ŸA
switcher, and input devices.
6. Select an input using the front panel input toggle switch or the contact closure controller.
7. The image should now display, and sound should be audible. If not, ensure that all devices are plugged in and receiving
power. Check the cabling and make adjustments as needed. Select a different input to check for a picture and sound.
Front Panel Features
VSW 2VGA A
INPUT 1
2
1
INPUT 2
C
B
A
D E F G
Figure 2. VSWī˜Ÿ2VGAī˜ŸA Front Panel Features
A ā€” This LED lights green whenever Input 1 (video and audio) is selected.Input 1 LED indicator
B ā€” This LED lights green whenever Input 2 (video and audio) is selected.Input 2 LED indicator
NOTE: The LEDs also serve as power up indicators. When the switcher is powered up, the selected input LED lights.
C ā€” Toggle this switch up to select Input 1. Toggle it down to select Input 2.Input select toggle switch
D ā€” Input VGA-UXGA, RGBHV, RGBS, RGsB, RsGsBs, component video, or HDTV component video through Input 1 video
this female 15-pin VGA connector.
3
VSWī˜Ÿ2VGAī˜ŸA ā€¢ User Guide (Continued)
E (see on the previous page) ā€” Input unbalanced stereo audio through this 3.5 mm mini audio jack (see Input 1 audio figureī˜Ÿ2
figureī˜Ÿ3).
Slee ( )ve
Ring (R)
Tip (L)
3.5 mm Stereo Plug Connector
(unbalanced)
Figure 3. Audio Input Connector
F ā€” Input VGA-UXGA, RGBHV, RGBS, RGsB, RsGsBs, component video, or HDTV component video through Input 2 video
this female 15-pin VGA connector.
G ā€” Input unbalanced stereo audio through this 3.5 mm mini audio jack (see figureī˜Ÿ3).Input 2 audio
Rear Panel Features
POWER
12V
.1A MAX
VSW 2VGA A
AUTO-SW
CONTACT
OUTPUT
VGA IN 1 LOOP
1 2
AUD OUT
A B C D E
Figure 4. VSWī˜Ÿ2VGAī˜ŸA Rear Panel Features
A ā€” Connect the included 12 VDC external power supply to the 2-pole 3.5 mm captive screw connector.Power connector
NOTE: One power supply can power up to five switchers (see on pageī˜Ÿ5).
Power Connnection
B ā€” Female 15-pin HD VGA connector for buffered local monitor output from Input 1Loop Thru Input 1 connector
C ā€” Female 15-pin HD VGA connector for output from Input 1 or Input 2. The output video type follows input type and Output
is either VGA-UXGA, RGBHV, RGBS, RGsB, RsGsBs, component video, or HDTV component video.
D ā€” Unbalanced stereo audio is output from this 3.5 mm mini audio jack (see figureī˜Ÿ5).Audio Output connector
Slee ( )ve
Ring (R)
Tip (L)
3.5 mm Stereo Plug Connector
(unbalanced)
Figure 5. Audio output connector
NOTE If you are daisy chaining, connect the other end of the audio cable to the Audio input 2 connector on the
downstream video switcher.
E ā€”Contact closure/Autoswitching (Contact/Auto-SW)
ā€¢ Contact closure ā€” Connect a contact closure device to this 3.5 mm, 3-pole captive screw connector.
ā€¢ Pin 1 selects Input 1 when momentarily connected to ground (pin 3).
ā€¢ Pin 2 selects Input 2 when momentarily connected to ground (pin 3).
ā€¢ Ground connects to the ground wire (equipment ground).
NOTE: Simultaneously connecting both pins 1 and 2 to ground (pin 3) turns autoswitching mode on.
AUTO-SW
CONTACT
1 2


Produktspezifikationen

Marke: Cecotec
Kategorie: SpĆ¼lmaschine
Modell: Bolero Aguazero 6500 FULL-BI C

Brauchst du Hilfe?

Wenn Sie Hilfe mit Cecotec Bolero Aguazero 6500 FULL-BI C benƶtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung SpĆ¼lmaschine Cecotec

Bedienungsanleitung SpĆ¼lmaschine

Neueste Bedienungsanleitung fĆ¼r -Kategorien-