Cateye Cordless 2 CC-CL200N Bedienungsanleitung

Cateye Fahrradcomputer Cordless 2 CC-CL200N

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Cateye Cordless 2 CC-CL200N (2 Seiten) in der Kategorie Fahrradcomputer. Dieser Bedienungsanleitung war für 28 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

sensor

OPERATION FEATURES

Two buttons are provided on the top of the main unit and two on the bottom.

These buttons are used as follows:

•Mode Button (top left button)

Whenever this button is pressed, the mode display changes in the order

shown in fig.1, and the data is displayed on the sub-display. If this Note:

button is kept pressed for more than 2 seconds, display appears.

•Start/Stop Button (top right button)

Measurement of trip distance, elapsed time and average speed is started or

stopped when the start/stop button is pressed. Whenever this button is

pressed, start and stop are repeated. During measurement the speed scale

symbol blinks.

Note: This button does not function if the auto mode function is set to ON

[Refer to the explanation of the Auto (Automatic Start/Stop) Function below].

•Set Button (bottom left button)

• To set the wheel circumference:

Stop the measurement in the (O) mode, then press the SET button.

• To set the 24-hour clock time:

Stop the measurement in ( ) mode, then press the SET button.

• To set auto mode to ON or OFF:

Select the (T),(A) or (D) mode, then press the SET button.

•AC (All Clear) Button (bottom right button)

When this button is pressed, all the data stored in memory is cleared.

After all displays illuminate, the "mile/h" symbol illuminates. This button should

be pressed only after replacing the battery or when irregular display of infor-

mation occurs due to static electricity,etc. Once this button is pressed and all

memory is erased, it will be necessary to set the wheel circumference, time,

etc. again. (refer to Main Unit Preparation)

Reset Operation: (Fig.2)

Press left button to select any mode except total distance (O) and press left

and right buttons together. Stored data of trip distance (D), elapsed time (T),

average speed (A) and maximum speed (M) are all reset to zero. (In the total

distance display mode, the current wheel circumference (A) or (B) is shown.)

MAIN UNIT PREPARATION

User must make the following setting according to instructions before

the cyclocomputer can be used properly.

1. How to measure the exact Wheel Circumference (L)(Fig.3)

First, adjust tire pressure and then put a mark on the tire tread and the ground

simultaneously. Then ride the bike one full wheel revolution. Mark the ground

at the end of one revolution and then measure the distance between the two

marks. This measure is your actual wheel circumference. Or, the "Setting Val-

ues Cross Reference Table" can help you to find out an approximate wheel

circumference according to tire size.

2. Setting the Speed Scale (Fig.4)

When the AC button is pressed and all displays illuminate then the "mile/h"

appears as shown in fig.4. "km/h" and "mile/h" are displayed alternatively each

time the right button is pressed. Select any speed scale as desired and press

SET button to complete the setting.

3. Setting the Wheel Circumference (Fig.5.6)

This cyclocomputer is able to memorize two different wheel circumferences.

One main unit can be used on two bicycles subject to buy another set of

bracket and sensor.

Two wheel circumferences, (A) 2155mm and (B) 2030mm, have been set be-

fore the cyclocomputer left our factory. The (A) wheel circumference 2155mm

(standard for 27 inch tire) will blink as shown in fig.5. If you want to enter

2155mm and 2030mm, simply press the SET button. If you want to change,

press either the right button to increase or left button to decrease the number.

To change the number rapidly keep the button pressed. Once you reach the

setting you want, press the SET button. If you want to set a second circumfer-

ence, press the left and right buttons together before pressing the SET button.

The wheel circumference 2030mm is displayed and blinks(fig.6). Set to a de-

sired wheel circumference in the same manner as the first circumference set-

ting and press SET button to complete the setting.

4. Selecting one of the two Wheel Circumference (Fig.7)

Set the Auto Mode to ON. (Refer to the explanation of Auto Mode function.)

While keeping the right button pressed , press the SET button. The first wheel

circumference measurement will be displayed for a few seconds, then the sec-

ond setting will appear.

5. How to reset the Wheel Circumference

Select the (O) mode and stop the measurement. Press SET button and the

already set wheel circumference will blink on the sub-display. Refer to '3.Set-

ting the wheel circumference' to complete the setting.

Setting the 24-hour Clock (Fig.8)

Press left button for more than 2 seconds to select the 24-hour clock display.

Stop the measurement by pressing the right button. Press SET button and the

minute display will start to blink. Press right button to select a minute time

ahead of the current time by 1 to 2 minutes. Next press left button and the hour

will blink. Press right button to set to current hour time. Press SET button to

complete the setting.

MOUNTING TO BIKE

Attach the bracket near handlebar stem, using rubber pad (fig. 9). Cut and

adjust the length of the rubber pad if necessary.

• Slide the main unit onto the bracket from front until it clicks into position. To

remove the main unit, pull it forward while depressing the lever on bracket

(fig.10).

How to Mount the Sensor on the Right Front Fork Leg.(fig.11)

Mount the sensor in the highest possible position on the right front fork leg.

Adjust the position, clearance and direction as follows:

(1) Insert the band B into the slit of the band A, and put the rubber pad inside

of the band A (fig. 12). Adjust the length of the bands in order that the

screw-fastening part of the bands is parallel when mounted to the fork (fig.

13). * To pull out the band B from band A, tug strongly.

(2) Mount the adjusted bands to fork along with the sensor, by temporarily

tightening the screw (fig. 14).If the space between front fork and spoke of

your bike is big, use the spacer and long screw as in the fig.15, so that the

clearance between sensor and magnet will be approx. 5mm.

(3) Attach the magnet securely to the right side of the spoke (fig. 16) so that

the magnet properly faces the sensor zone (fig. 17).

(4) A 5mm clearance shall be kept between the sensor and magnet(fig.18).

Then align the magnet with sensor zone (fig.16). Meanwhile, the sensor

shall aim at the main unit indicated by the triangle marked on the sensor.

Then tighten the screw to secure the sensor in position. Cut the excess

sensor band B with scissors or the like.

Check points for sensor mounting:

1.Keep a 5 mm clearance between the sensor and magnet.

2.The magnet surface shall align to the sensor zone.

3.The triangle mark on the sensor shall aim at the main unit.

INSTRUCTION MANUAL

bracket

slide

front

front fork

magnet

sensor band B

front fork

screw

magnet

CR2032

OPEN CR2032

sensor

rubber pad

sensor

rubber pad

Fig.9

Fig.10

Fig.11

Fig.12

sensor band A

Fig.14

Fig.15

Fig.18

Fig.19

OPEN

Fig.20

sensor zone

spoke

rubber pad

sensor band A

Fig.13

parallel

lever

Reset

less than

5mm

POWER SAVING FUNCTION

When the main unit is left without receiving any signal for one hour, the power will

be turned off automatically. Resulting in SLEEP state in which only the 24-hour

clock displays. The main unit can not receive any signal in this state. Press left or

right button to restore signal reception.

Note: Remember to restore signal reception before every journey.

MAINTENANCE/PRECAUTIONS

• Do not leave the main unit exposed to direct sunlight when the unit is not in use. Do not disassemble

the main unit.

• Don't pay too much attention to your computer's functions while riding! Keep your eyes on the road

and give due consideration to traffic safety.

• Check the relative position of magnet and sensor periodically.

• For cleaning, use neutral detergent on soft cloth, and wipe off later with dry cloth. Do not apply paint

thinner, benzine, or alcohol, which may damage on the surface.

TROUBLE SHOOTING

No display. ------------------------------------------------------ Replace the main unit battery with new one.

Incorrect data appears. -------------------------------------- Execute "All Clear" operation.

Figures do not appear on the main display ------------- Cancel the power saving function.

Current speed does not appear. --------------------------- Check the sensor position and direction.

Speed is not displayed when riding with high speed or at low temperature.

--------------------------------------------------------------------- Check the sensor position and direction.

--------------------------------------------------------------------- Has the battery worn out?

Even when the right button is pressed, the cyclocomputer does not operate.

--------------------------------------------------------------------- Set the auto mode to OFF.

The entire liquid crystal screen is dark and unusual display is seen where it should not be.

--------------------------------------------------------------------- It returns to normal state if left in the shade.

Display response is slow. ----------------------------------- It returns to normal state when temperature rises.

SPECIFICATIONS

Applicable Cycle Sizes 10 mm - 2,999 mm(Initial value: A:2155 mm B:2030 mm)

Power Supply Main unit: ------------------------------------ Lithium Battery (CR2032)x1/approx. 2years

Sensor with transmitter: ------------------ Lithium Battery (CR2032)x1/approx. 1,000miles

Dimension / Weight 2"x 1-13/10"x 29/32" / 1.2 oz (29 g)

* The specifications and design are subject to change without notice.

AUTO (AUTOMATIC START/STOP) FUNCTION

The Cordless 2 is equipped with a selective auto function allowing automatic start

or stop of measurement without using the right button.

How to Set On/Off the Auto Function

Select (T), (D) or (A) to sub-display and then press SET button. The

symbol

will display when auto function is set ON. Repeat to set OFF the auto function.

Note: In SLEEP state, auto start will not function. Press left or right button to restore

signal reception first. (Refer to Power Saving Function)

SCurrent Speed 0.0(3.0) to 65.9 miles/hr ±0.3mile/h

This is always displayed on the main display and updated once a second.

OTotal Distance 0.0 to 99,999 miles ±0.1mile

This is continuously measured until battery wears down or all clear operation is

done. At 100,000 miles(km), it returns to zero and counting begins anew.

DTrip Distance 0.00 to 999.99 miles 0.01mile

The trip distance from start to current point is displayed. With Reset operation, it

returns to zero.

TElapsed Time 0:00'00" to 9:59'59" ±0.003%

Elapsed time is measured from start to current point, in units of hours, minutes and

seconds. At 10 hours, it returns to zero and counting begins anew. With Reset

operation, it returns to zero.

AAverage Speed 0.0 to 65.9 miles/hr 0.3mile/h±

The average speed from start to current point is displayed within 27 hours 46 min-

utes 39 seconds (99,999 seconds) or 999.99 miles (km). If either is exceeded, (.E)

is displayed and calculation ceases.

MMaximum Speed 0.0 (3.0) to 65.9 miles/hr ±0.3mile/h

With Reset operation, it returns to zero and counting begins anew.

24 hr. Clock Time 0:00´ to 23:59´ 0.003%±

The current time is displayed by a 24-hour clock.

DISPLAY FUNCTIONS

H. Sub-Display

(Selected function)

I. Start/Stop Button

J. Battery Case Cover

K. Set Button

L. AC Button

A. Main Display (Speed)

B. Wheel Circumference Mark

C. Mode Symbol

D. Mode Button

E. Wheel Sensor Pulse Symbol

F. Speed Scale Symbol

G. Auto Mode Symbol

1. Bracket

2. Sensor(Transmitter)

3. Sensor Band A

4. Sensor Band B

5. Magnet

6. Rubber Pad

Fig.2

Fig.4

Fig.5

Fig.6

Fig.8

Fig.7

Fig.1

Fig.3

7. Screw

8. Long Screw

9. Spacer

10.Attachment for aerofork

11.Nylon Tie

spacer long screw

Fig.21 contact

Attachment for aerofork

In case of

aerofork

Fig.16 magnet

spoke

fixing nut

ENS OR

ONE

sensor zone

triangle mark

magnet

Fig.17

To remove

push

pull

TEST

Mount the main unit on the bracket. If current speed doesn't appear on the

main display, press either left or right button to release the unit from the power

saving mode. Then spin the front wheel to make sure the wheel sensor pulse

symbol flickers. If it does not flicker, adjust the position of sensor until it flickers

normally. The mounting is completed and the cyclocomputer is operational.

THE CORDLESS SYSTEM

The sensor picks up wheel revolution signal and transmits the signal to the

receiver in the main unit. The main unit receives, calculates and displays the

data. The approximate service hour of batteries is as follows:

The main unit (receiver): --- Approx. 2 years (average 1 hour's use per day)

The sensor (transmitter): ------- Total distance of approx. 10,000 miles (16,000 km)

Note: To prevent external signal interference, the sensor signal reception

range is restricted. For best performance, the triangle mark

on the sensor shall

aim at the direction to the main unit. The distance between the sensor and

main unit must be kept within 70 cm. The signal reception range may shorten

as a result of low ambient temperature or lowered battery power. It is advisable

to replace the sensor battery before it fails. The battery service hours quoted

above is the average for a 65 cm distance between the sensor and main unit.

•The cordless system may be interfered with in the following situation, so that

main unit may display false data.

1. Riding near railroad crossings and trains.

2. Riding in places where intensive electromagnetic wave or field exist,

such as TV transmission station and radar installations.

3. When two bicycles carrying similar cyclocomputers are ridden side by

side.

REPLACING THE BATTERIES

Batteries are already loaded in the main unit and the sensor.

How to replace battery in Main Unit (Fig.20)

Open the battery cover on the back and insert a new CR2032 (lithium) with the

(+) pole upward, while pressing the side of the battery against the contact.

Press AC button to erase all stored data and then redo the settings.

How to replace battery in Sensor (Fig.21)

Take off the sensor from the bicycle. Open the battery cover on the back and

insert a new CR2032 (lithium) with the (+) pole upward, while pressing the side

of the battery against the contact. Mount the sensor back to the bicycle and

adjust to relative position, clearance and direction.

#169-6690N

Parts Kit

Kit d'accessoires

Ersatzteil

Onderdelen set

Kit d'accessori

Kit de piezas

#169-6660N

Bracket Kit

Kit support d'unite principale

Halterung

Bracketkit

Kit supporto

Soporte

#169-6670N

Cordless Sensor

Palpeur (Emetteur)

Sensor mit Sender

Sensor-draadloos

Sensore"Senzafilo"

Sensor sin cable

#169-9780 #169-6680

Attachment for aerofork Universal Sensor Band

Fixation pour fourche AERO Collier Universel de Détecteur

Zusatz zur Federgabel Universalsensorband

Bevestiging voor aerovork Universele Sensorband

Attacco per forcella aerodinamica Fascetta Universale di sensore

Sujección para horquilla aerodinámica Banda universal del sensor

#169-6667

Center Mount Bracket Kit

Kit de montage central del l principale´unité

Halterung für Montage en der Lenkermitte

Stuurbocht Bevestinging Set

Kit di Montaggio al Centro del manubrio

Kit Soporte para Montaje Central

#169-6669

Stem Mount Bracket Kit

Kit de montage de l principale sur la broche du guidon´ éunit

Halterung für Montage en der Lenkerstange

Stuurpen Bevestiging Set

Kit di Montaggio sull attacco manubrio´

Kit Soporte para Montaje en Tija

#169-9691 #166-5150

Wheel Magnet Lithium Battery (CR2032)

Aimant pour roue Pile au lithium (CR2032)

Radmagnet Lithium-Batterie (CR2032)

Wielmagneet Lithium Batterij (CR2032)

Magnete ruota Batteria al Litio (CR2032)

Iman de la rueda Bateria de Litio (CR2032)

US. PAT. NO.4633216, 4636769, 4642606, 5236759 and Patent Pending

Design Patented

CCMCL2-010402

Setting Values Cross Reference Table

(The tire size is marked on both sides of the tire.)

Table de Correspondance des Valeurs de Réglage

(La dimension du pneu figure de chaque c du pneu)ô ét

Wertetabelle zur Einstellung des Radumfanges (die Radgröße entnehmen Sie der Aufschrift des Reifens)

Tabel voor het bepalen van de wielomtrek (de bandenmaat staat vermeld aan beide zijden van de band)

Tabella delle Corrispondenze dei Valori di Regolazione (La dimensione del pneumatico figura su ogni lato del pneumatico)

Tabla de Valores (El tama o de la rueda est marcado al lado de la llanta)ñ á

Specificat ions/Caracteristiques techniques/ / /Technisc he daten Specificaties

Caratteristiche tecniche/

Especificaciones

Controller/

Calculateur

/ / / /Controler Controleur Elaboratore

Contador

-------------------------------------- 4-bit 1-chip Microcomputer (Crystal Controlled Oscillator)

Display/

Affichage

/ / / /Anzeige Display Visualizzazione

Pantalla

------------------------------------------------------------------------------------ Liquid Crystal Display

Sensor/

Détecteur

/ / / /Sensor Sensor Rivelatore

Sensor

--------------------------------------------------------------------------- No Contakt Magnetic Sensor

Cordless Système/

System sans fil

/ / / /Kabelloses System Draadloze systeem Sistema sin hilos

Sistema cordless

---------------------------------------------------------------- Directional electromagnetic induction

Operating Temperature Range/

Température d’utilisation

/ / /zulässige Betriebstemperatur Toegestane temp. Temperatura di utilizzo

-------------------------------------------------------------------------------- 0 F)°C - 40°C(32°F - 104°

LIMITED WARRANTY

2-Year Warranty: Only Main Unit/Sensor

If trouble occurs during normal use, the part is repaired or replaced free of charge. The service must be

performed by CAT EYE Co., Ltd.. and the product needs service must be returned to CAT EYE Co., Ltd.

directly by purchaser. When returning the product for CAT EYE warranty service, pack it very carefully,

and enclose the warranty certiﬁcate and instructions for repair. Please make sure to write or type your

name and address clearly on the warranty certificate, so that the product can be shipped back to you as

soon as the necessary repair/adjustment is completed. Insurance, handling and transportation charges

to our service shall be borne by person desiring service.

Address for service

CO.,LTD.

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan

Attn.: CAT EYE Customer Service Section

Service & Research Address for United States Consumers:

CAT EYE Service & Research Center

1705 14th St. 115 Boulder, CO 80302

Phone: 303-443-4595 Toll Free: 800-5CATEYE

Fax: 303-473-0006 e-mail: CatEyeUSA@aol.com

GARANTIE LIMITEE

Garantie de 2 ans : Unit Principale / D tecteur uniquementé é

En cas de probl me en cours d'utilisation normale, le produit sera r ou remplac gratuitement. Les r parations doivent è éparé é é être

effectuées par CAT EYE Co., Ltd. et le produit à réparer doit être retourné à CAT EYE Co., Ltd. directement par l'acheteur. Tout

produit retourn au service de r paration CAT EYE doit tre soigneusement emball et le certificat de garantie ainsi que lesé é ê é

instructions de r paration doivent accompagner le produit parer. Il est conseill l'acheteur d' crire lisiblement ou de dacty-é à é r é à é

lographier ses nom et adresse sur le certificat de garantie, afin que le produit puisse lui tre directement retourn s que lesê é è d

réparations/réglages nécessaires sont terminés. Le coût de l'assurance ainsi que les frais de manutention et de transport vers le

service de r paration CAT EYE sont charge de la personne souhaitant une r paration sous garantie.é à é

Adresse d'envoi pour réparation

CO.,LTD.

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japon.

Attn : CAT EYE Customer Service Section.

BEGRENZTE GARANTIE

2-Jahres-Garantie: Auf den Computer und den Sensor

Falls während des normalen Gebrauchs Fehler auftreten, wird das entsprechende Teil kostenlos re-

pariert oder ersetzt. Die Reparatur muß von CAT EYE Co., Ltd. durchgeführt werden, und das zu

reparierende Produkt muß direkt durch den Händler an CAT EYE Co., Ltd. gesandt werden. Bei der

Rückgabe des Gerätes zur Reparatur packen Sie es sorgfältig anbei. Achten Sie darauf, Ihren Namen

und Ihre Anschrift klar und deutlich lesbar auf die Garantiekarte zu schreiben, damit das Gerät so

schnell wie möglich nach Beendigung der notwendigen Reparatur/Einstellung an Sie zurückgesandt

werden kann.

Anschrift bei Garantieansprüchen

CO.,LTD.

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan

z. H.: CAT EYE Kundendienstabteilung oder wenden Sie sich bitte an den entsprechenden Importeur.

GARANTIEBEPALINGEN

Garantie: 2 jaar op computer en sensor

Mochten er problemen optreden gedurende normaal gebruik, dan geschiedt reparatie of vervanging kosteloos.

Dit dient door de fabrikant Cateye Co., Ltd. uitgevoerd te worden. De computer moet door de importeur aan

Cateye Co., Ltd. teruggezonden worden. Bij terugzending van de computer moet deze zorgvuldig verpakt worden

en dient het garantiebewijs, de aankoopbon en een beschrijving van het probleem meegezonden te worden. Ver-

meldt duidelijk uw naam en adres in blokletter of met de schrijfmachine op het garantiebewijs, zodat de computer

in goede orde terruggestuurd kan worden.Verzekerings-, verzend- en transportkosten zijn voor rekening van de

koper.

Adres:

CO.,LTD.

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan

Ter attentie van: Cateye klantenservice

Zogauw als de reparatie/vervanging geschiedt is, wordt de computer aan u geretourneerd.

LIMITAZIONE DELLA GARANZIA

Garanzia di due anni

Questo prodotto CATEYE garantito con la riserva di una utilizzazione corretta, contro ogni difetto diè

fabbrica e di materiale. Le riparazioni effettuate nel quadro della presente garanzia sono gratuite a

condizione che siano rispettate le seguenti disposizioni. Il costo dell'assicurazione come le spese di

stoccaggio e di trasposrto sono a carico di chi richiede la riparazione. Questa garanzia è limitata alla

riparazione dell'unit principale esclusi il filo, il supporto e qualsiasi accessorio. Si prega il compratore dià

scrivere chiaramente il proprio Cognome Nome ed indirizzo sul Certificato di garanzia completandolo in

tutte le sue parti (Rivenditore/Data di acquisto etc.).

Indirizzo per la rispedizione per riparazione

CO.,LTD.

2-8-25, Kuwazu, Higashi-Sumiyoshi-ku, Osaka 546-0041, Giappone.

Att.: Dipartamento Assistenza Clienti

TEL.: 81-6-6719-7781 FAX: 81-6-6719-2362

GARANTÍA LIMITADA.

2 Años de Garantía: Sólo Unidad Principal/Sensor.

Si sucedieran problemas durante un uso normal, la pieza ser reparada o reemplazada gratuitamente. El servicio debeá

ser realizado por CATEYE CO., LTD. y el producto que necesite del servicio debe ser devuelto a CATEYE directamente

por el comprador. Cuando se env e el producto al servicio de garant a de CATEYE se p2-ha de empaquetar muy cuidado-í í

samente y adjuntar el certificado de garant a e instrucciones para la reparaci n. Por favor, aseg rese de escribir clara-í ó ú

mente su nombre y direcci n en el certificado de garant a, con objeto de que el producto le sea devuelto a Vd. tan prontoó í

como la reparación o ajuste necesario haya sido efectuado. Los gastos del seguro, manejo y transporte hasta nuestro

servicio ser n a cargo de la persona demandante de servicio.á

Para reparación enviar a:

CO.,LTD.

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan

Attn.: CAT EYE Customer Service Section

CYCLOCOMPUTER

Model CC-CL200N This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

Modifications

The FCC requires the user to be notified that any changes or modifications made to

this device that are not expressly approved by Cat Eye Co., Ltd. may void the user’s

authority to operate the equipment.

TIRE SIZE L(mm)

dimension du pneu

Radgröße

bandenmaat

dimensione del pneumatico

Tamaño de rueda

26 x 1.50 1985

26 x 1.75 2030

26 x 1.95 2050

26 x 2.00 2055

26 x 2.1 2068

26 x 2.125 2070

26 x 2.35 2083

27 x 1 2145

27 x 1-1/8 2155

27 x 1-1/4 2161

27 x 1-3/8 2169

650 x 35A 2090

650 x 38A 2125

650 x 38B 2105

TIRE SIZE L(mm)

dimension du pneu

Radgröße

bandenmaat

dimensione del pneumatico

Tamaño de rueda

24 x 1 1753

24 x 3/4 Tubular 1785

24 x 1-1/8 Tubular 1795

24 x 1-1/4 1905

24 x 1.75 1890

24 x 2.00 1925

24 x 2.125 1965

26 x 1(559mm) 1913

26 x 1(650c) 1952

26 x 1.25 1953

26 x 1-1/8 Tubular 1970

26 x 1-3/8 2068

26 x 1-1/2 2100

26 x 1.40 2005

TIRE SIZE L(mm)

dimension du pneu

Radgröße

bandenmaat

dimensione del pneumatico

Tamaño de rueda

700 x 18C 2070

700 x 19C 2090

700 x 20C 2086

700 x 23C 2096

700 x 25C 2105

700 x 28C 2136

700 x 30C 2170

700 x 32C 2155

700C Tubular 2130

700 x 35C 2168

700 x 38C 2180

700 x 44C 2224

Produktspezifikationen

Marke:	Cateye
Kategorie:	Fahrradcomputer
Modell:	Cordless 2 CC-CL200N

Brauchst du Hilfe?

Wenn Sie Hilfe mit Cateye Cordless 2 CC-CL200N benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Fahrradcomputer Cateye

Cateye CC-ED400 Enduro Bedienungsanleitung

14 Oktober 2024

Cateye Inou MSC-GC100 Bedienungsanleitung

29 September 2024

Cateye Mate CC-3000 Bedienungsanleitung

22 September 2024

Cateye Strada CC-RD430DW Bedienungsanleitung

10 September 2024

Cateye Vectra Wireless CC-VT100W Bedienungsanleitung

5 September 2024

Cateye CC-RD430DW Strada Bedienungsanleitung

3 September 2024

Cateye CC-RD410DW Strada Bedienungsanleitung

1 September 2024

Cateye CC-RD400DW Strada Bedienungsanleitung

27 August 2024

Cateye OS 1.1. Bedienungsanleitung

13 August 2024

Cateye Padrone Smart CC-PA500B Bedienungsanleitung

12 August 2024

Bedienungsanleitung Fahrradcomputer

Neueste Bedienungsanleitung für -Kategorien-

Blackburn Delphi 5.0 Bedienungsanleitung

14 Oktober 2024

Prophete 0512 Bedienungsanleitung

13 Oktober 2024

CicloSport CicloMaster CM 408 Bedienungsanleitung

13 Oktober 2024

Vetta RT255L Bedienungsanleitung

12 Oktober 2024

Filzer dZ4LW3 Bedienungsanleitung

12 Oktober 2024

Falk Pantera Bedienungsanleitung

12 Oktober 2024

Trek Incite 11i Bedienungsanleitung

12 Oktober 2024

Sunding SD-563A Bedienungsanleitung

10 Oktober 2024

Blackburn Delphi 4.0 Bedienungsanleitung

9 Oktober 2024

CicloSport CicloMaster CM 2.11 Bedienungsanleitung

9 Oktober 2024