Casio Tough Solar WS220-1AV Bedienungsanleitung

Casio Sportuhr Tough Solar WS220-1AV

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Casio Tough Solar WS220-1AV (6 Seiten) in der Kategorie Sportuhr. Dieser Bedienungsanleitung war für 32 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/6

Operation Guide 3271

MO1106-EA

E-1

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out of your

purchase, be sure to read this manual carefully.

•Be sure to keep all user documentation handy for future reference.

Keep the watch exposed to bright light

The electricity generated by the solar cell of the watch is

stored by a rechargeable battery. Leaving or using the

watch where it is not exposed to light causes the battery

to run down. Make sure the watch is exposed to light as

much as possible.

•When you are not wearing the watch on your wrist,

position the face so it is pointed at a source of bright

light.

•You should try to keep the watch outside of your sleeve

as much as possible. Charging is reduced significantly if

the face is covered only partially.

Bright Light

Solar cell

E-2

All

functions

enabled

LEVEL 1

LEVEL 2

LEVEL 3

LEVEL 4

Charge

Rechargeable battery

Bright Light

Electrical

energy

Solar cell

(Converts light to

electrical power.)

LEVEL 1

LEVEL 2

LEVEL 3

LEVEL 4

Some or all

functions

disabled

Dis-

charge

Battery charges in the light. Battery discharges in the dark.

•The watch continues to operate, even when it is not exposed to light. Leaving the

watch in the dark can cause the battery to run down, which will result in some watch

functions to be disabled. If the battery goes dead, you will have to re-configure watch

settings after recharging. To ensure normal watch operation, be sure to keep it

exposed to light as much as possible.

E-3

•The actual level at which some functions are disabled depends on the watch model.

•Frequent display illumination can run down the battery quickly and require charging.

The following guidelines give an idea of the charging time required to recover from a

single illumination operation.

Approximately 5 minutes exposure to bright sunlight coming in through a window

Approximately 8 hours exposure to indoor fluorescent lighting

•Be sure to read “Power Supply” (page E-39) for important information you

need to know when exposing the watch to bright light.

If the display of the watch is blank...

If the display of the watch is blank, it means that the watch’s Power Saving function

has turned off the display to conserve power.

•See “Power Saving Function” (page E-51) for more information.

E-4

About This Manual

•Button operations are indicated using the letters shown in the illustration.

•Each section of this manual provides you with the information you need to perform

operations in each mode. Further details and technical information can be found in

the “Reference” section.

E-5

Contents

General Guide ......................................................................................................... E-8

Timekeeping .......................................................................................................... E-11

Stopwatch .............................................................................................................. E-17

Recall Mode ........................................................................................................... E-21

Countdown Timer .................................................................................................. E-25

World Time ............................................................................................................. E-29

Alarms .................................................................................................................... E-32

Illumination ............................................................................................................ E-37

Power Supply ........................................................................................................ E-39

Reference .............................................................................................................. E-47

Specifications ....................................................................................................... E-55

E-6

Procedure Lookup

The following is a handy reference list of all the operational procedures contained in

this manual.

To exit the demo mode ......................................................................................... E-10

To set the time and date ....................................................................................... E-12

To change the Daylight Saving Time (summer time) setting ............................ E-16

To measure times with the stopwatch ................................................................ E-18

To position the lap time and split time on the display ...................................... E-19

To recall stopwatch records ................................................................................ E-21

To delete a log ....................................................................................................... E-23

To delete all logs ................................................................................................... E-24

To configure the countdown timer ...................................................................... E-26

To use the countdown timer ................................................................................ E-28

E-7

To view the time in another city ........................................................................... E-30

To toggle a city code time between Standard Time and

Daylight Saving Time ...................................................................................... E-31

To set an alarm time ............................................................................................. E-33

To test the alarm ................................................................................................... E-34

To turn an alarm on and off .................................................................................. E-35

To turn the Hourly Time Signal on and off .......................................................... E-36

To illuminate the display manually ...................................................................... E-37

To specify the illumination duration ................................................................... E-38

To turn the button operation tone on and off ..................................................... E-50

To recover from the sleep state ........................................................................... E-52

To turn Power Saving on and off ......................................................................... E-52

E-8

General Guide

•Press C to change from mode to mode.

•In any mode, press L to illuminate the display.

Timekeeping Mode

Stopwatch Mode

▲

E-9

Countdown Timer Mode

Alarm Mode World Time Mode

Recall Mode

C C

▲

Operation Guide 3271

E-10

Demo Mode

In the Timekeeping Mode, holding down C for about three seconds will enter the

demo mode. In the demo mode, the screen cycles through the normal timekeeping,

stopwatch, and World Time screens in five-second intervals.

To exit the demo mode

Press any button.

E-11

Timekeeping

Use the Timekeeping Mode to set and view the current time and date.

Read This Before You Set the Time and Date!

This watch is preset with a number of city codes, each of which represents the time

zone where that city is located. When setting the time, it is important that you first

select the correct city code for your Home City (the city where you normally use the

watch). If your location is not included in the preset city codes, select the preset city

code that is in the same time zone as your location.

•

Note that all of the times for the World Time Mode city codes (page E-29) are displayed

in accordance with the time and date settings you configure in the Timekeeping Mode.

Hour : Minutes

Seconds

Day of week

Year – Month – Day

PM indicator

E-12

To set the time and date

1. In the Timekeeping Mode, hold down A until the city

code starts to flash, which indicates the setting screen.

2. Use D and B to select the city code you want.

•Make sure you select your Home City code before

changing any other setting.

•For full information on city codes, see the “City Code

Table” at the back of this manual.

3. Press C to move the flashing in the sequence shown below to select the other

settings.

Seconds

12/24-Hour

Format Hour Minutes

DST

Month Year

City Code

DayPower Saving Illumination

Duration

Button

Operation Tone

E-13

•The following steps explain how to configure timekeeping settings only.

4. When the timekeeping setting you want to change is flashing, use D or B to

change it as described below.

Change the city code

Toggle between Daylight Saving Time ( )

and Standard Time ( )

Toggle between 12-hour ( ) and 24-

hour ( ) timekeeping

Reset the seconds to

Change the hour and minutes

Use D (east) and B

(west).

Press D.

Use D (+) and B (–).

Screen: To do this: Do this:

E-14

5. Press A to exit the setting screen.

•The day of the week is displayed automatically in accordance with the date (year,

month, and day) settings.

Screen: To do this: Do this:

Change the year, month, or day

Toggle the button operation tone between

(on) and (off)

Toggle the illumination duration between

(approximately 1.5 seconds) and

(approximately 3 seconds).

Toggle between Power Saving on ( ) and

off ( )

Use D (+) and B (–).

Press D.

E-15

12-hour and 24-hour timekeeping

•With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for

times in the range of noon to 11:59 p.m. and no indicator appears to the left of the

hour digits for times in the range of midnight to 11:59 a.m.

•With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without

any indicator.

•The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is

applied in all other modes.

Daylight Saving Time (DST)

Daylight Saving Time (summer time) advances the time setting by one hour from

Standard Time. Remember that not all countries or even local areas use Daylight

Saving Time.

E-16

To change the Daylight Saving Time (summer time) setting

1. In the Timekeeping Mode, hold down A until the city

code starts to flash, which indicates the setting screen.

2. Press C and the DST setting screen appears.

3. Use D to cycle through the DST settings in the

sequence shown below.

4. When the setting you want is selected, press A to exit

the setting screen.

• The DST indicator appears to indicate that Daylight

Saving Time is turned on.

DST indicator

E-17

Stopwatch

The 1/100-second stopwatch can measure elapsed time

and lap/split times. Stopwatch times are stored in memory.

•The stopwatch measurement operation continues even

if you exit the Stopwatch Mode.

•Exiting the Stopwatch Mode while a lap/split time is

frozen on the display clears the lap/split time and returns

to elapsed time measurement.

•All of the operations in this section are performed in the

Stopwatch Mode, which you enter by pressing C (page

E-8).

Note

•See page E-49 for information about the type of data the

watch stores in memory when you use the stopwatch.

•Use the Recall Mode (page E-21) to view data stored in

memory.

Split time

Remaining memory

Lap time

Graphic Area

E-18

To measure times with the stopwatch

➤➤➤➤

ClearNext Lap/

Split

➤

Start Stop

Elapsed Time

Re-start Clear

Stop

D D B

Lap/Split Times

Start Lap/Split

Stop

BD➤B

➤➤

Note

•Pressing B to perform a lap/split time operation freezes the lap/split time at that

point on the display for about eight seconds. After that, the display returns to normal

stopwatch time measurement.

•During a stopwatch time measurement operation, the current lap/split number is

shown at the top of the display, and the lap time and split time are shown in the

middle and at the bottom. You can change the positions of the lap time and split time

by pressing A while a stopwatch operation is in progress or stopped. For details,

refer to “To position the lap time and split time on the display” (page E-19).

Lap/Split indicator

Lap time

Lap/Split indicator

Split time

E-19

To position the lap time and split time on the display

Each press of cycles the lap time and split time positions in the sequence shownA

below.

•You can perform the above operation while stopwatch operation is ongoing or

stopped.

Split time

Remaining memory

Lap time Graphic Area

➤ ➤ ➤

A A A

➤

Lap time

Hours Seconds

Minutes

Hours Seconds

Minutes

Split time

Operation Guide 3271

E-20

•A graphic animation plays on the display while a stopwatch timing operation is being

performed. You can toggle the animation on and off by holding down A while the

stopwatch is reset to all zeros.

More than 10 hours

•Whenever the elapsed time exceeds 10 hours, the measurement changes from

1/100-second units to 1-second units.

E-21

Recall Mode

Use the Recall Mode to recall and delete records stored

by the Stopwatch Mode.

•Stopwatch records are stored in “logs” that are created

automatically by the watch. See “Memory Management”

on page E-47 for more information.

•The title screen of the newest log appears first whenever

you enter the Recall Mode.

•Log numbers are automatically assigned in sequence,

starting from 01.

•All of the operations in this section are performed in the

Recall Mode, which you enter by pressing C (page E-9).

To recall stopwatch records

In the Recall Mode, use A to scroll through the log title

screens, starting from the newest one, as shown below.

When the title screen of the log you want is displayed, use

D B (+) and (–) to cycle through the records contained in

the log.

Log number

Creation date

(Month – Day)

Log Title Screen

Time measurement

was performed

E-22

Split time

Lap/Split number BEST indicator

Log Title Screen

Stopwatch Record

Screen

Best Lap Time

Screen

Lap time

▲

E-23

•The locations of the lap time and split time in the Stopwatch Record screen are

determined by the display format you last selected in the Stopwatch Mode (page

E-17).

•The BEST indicator identifies the record that contains the best lap time in the log.

•If a best lap time record is deleted automatically when the log becomes full, the

BEST indicator will not be transferred to the record with the next best lap time. See

“Memory Management” on page E-47 for more information about automatic deletion

of records.

To delete a log

1. In the Recall Mode, display the title screen or one of the records of the log you want

to delete.

2. While holding down B D, hold down for about two seconds until the watch beeps.

•“CLR” will flash on the display for two seconds and then the watch will beep.

Release B and D at this time.

•You cannot delete the log of an ongoing elapsed time measurement operation.

E-24

To delete all logs

1. While holding down B D, hold down for about five seconds until the watch beeps

once and then a second time.

•“CLR” will flash on the display for two seconds and then the watch will beep once.

Keep B D and depressed and “ALL” will flash on the display for three seconds,

and then the watch will beep again. This indicates that all log data is cleared.

•You cannot delete logs while an elapsed timing operation is in progress.

E-25

Countdown Timer

Dual timers can be set with two different starting times.

The watch can be configured so the two timers alternate,

so when one reaches the end of its countdown, the other

timer starts. You can specify a “number of repeats” value,

which controls how many times the two-timer countdown

operation is performed (1 = once, 2 = twice, etc.). The

starting time of each timer can be set in five-second steps

up to 99 minutes, 55 seconds.

You can specify up to 10 repeats. The watch emits a short

beep whenever either of the timers reaches the end of its

countdown during an ongoing timer operation. The watch

emits a 5-second beep when the end of the final timer

operation (specified by the number of repeats) is reached.

Countdown End Beeper

The countdown end beeper lets you know when the countdown reaches zero. The

beeper stops after about 5 seconds or when you press any button.

Seconds

Minutes Timer 1

Number of Repeats

E-26

To configure the countdown timer

1. While the countdown start time is on the display in the

Countdown Timer Mode, hold down A until the current

countdown start time starts to flash, which indicates the

setting screen.

•If the countdown start time is not displayed, use the

procedure under “To use the countdown timer” (page

E-28) to display it.

2. Press C to move the flashing in the sequence shown

below to select other settings.

Timer 1

Minutes

Timer 1

Seconds

Timer 2

Seconds

Timer 2

Minutes

Number of Repeats

E-27

•To disable either timer, set 00'00" as its countdown start time.

4. Press A to exit the setting screen.

Button Operation

Use D B (+) and (–) to change the setting.

Setting

Minutes, Seconds

Number of Repeats

Screen

3. When the setting you want to change is flashing, use D B and to change it as

described below.

E-28

To use the countdown timer

Press while in the Countdown Timer Mode to start the countdown timer.D

•The countdown is performed by alternating between Timer 1 and Timer 2. A short

beep is emitted to signal a changeover from one timer to the other.

•Press D to pause a countdown. Press again to resume.D

•Pressing B while a countdown timer is stopped resets it to the start time specified

by you.

•The watch emits a 5-second beep when the end of the final timer operation

(specified by the number of repeats) is reached.

•Even if you exit the Countdown Timer Mode, the countdown timer operation

continues and the watch beeps as required.

Current timer time

Preset number of repeatsCurrent repeat count

Current time

Timer 1 or 2

(Reset)

(Start/Stop)

E-29

World Time

World Time shows the current time in 48 cities (31 time

zones) around the world.

•The times kept in the World Time Mode are

synchronized with the time being kept in the

Timekeeping Mode. If you feel that there is an error in

any World Time Mode time, check to make sure you

have the correct city selected as your Home City. Also

check to make sure that the current time as shown in

the Timekeeping Mode is correct.

•Select a city code in the World Time Mode to display the

current time in any particular time zone around the

globe. See the “City Code Table” at the back of this

manual for information about the UTC differential

settings that are supported.

•All of the operations in this section are performed in the

World Time Mode, which you enter by pressing C

(page E-9).

Current time in

selected city

City code

Produktspezifikationen

Marke:	Casio
Kategorie:	Sportuhr
Modell:	Tough Solar WS220-1AV
Bandmaterial:	Harz
Wasserfest:	Ja
Uhrmodus:	12 h / 24 h
Kalender:	Ja
Stoppuhr:	Ja
Gewicht:	46 g
Produktfarbe:	Schwarz
Abmessungen (BxTxH):	51.7 x 49.8 x 14.6 mm
Wasserdicht bis Tiefe:	100 m
Batteriestandsanzeige:	Ja
Weltzeitfunktion:	Ja
Akkurazität:	+/- 30 Sek/Monat
Solarenergie:	Ja