Cascade Audio Engineering APS-15 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Cascade Audio Engineering APS-15 (8 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/8
APS Power Supply
15, 30, 45, 55, 75, 90 and 100 Amp
Installation Guide
Congratulations and thank you for purchasing a Cascade Audio Engineer-
ing APS Power Supply. It is designed to provide years of efficient, trouble free
service.
All Cascade Audio Engineering APS power supplies feature regulated and
filtered outputs that provide clean power without the slightest hint of noise.
The advanced circuitry utilized in our APS power supplies offer efficiency
ratings of 86-90%. Their super light weight (6 - 7 lbs.), low-profile design
allows for convenient mounting in or under a display vehicle (car, boat, plane,
armored personnel carrier, etc.) or behind a display board.
Your new APS power supply may be used with or without a battery. How-
ever, when combined with a high quality battery, APS power supplies can
supply transient surges up to 1000 amps. In display applications where use
of a battery are not possible, installation of a Cascade Audio CAP-1 (1
Farad) or CAP-0.5 (1/2 Farad) capacitor is recommended. APS power sup-
plies may also be connected in parallel for even higher current operation!
Because all APS Power Supplies utilize an advanced switching design, there
is no low frequency transformer hum. Every power supply is equipped with a
quiet running cooling fan.
When not in use APS Series Power Supplies are essentially off, reducing
electricity usage. 1
Protection
All Cascade Audio Engineering APS Power Supplies feature temperature,
overcurrent and reverse-polarity protection circuitry. They will provide stable
regulated DC output voltage (13.6V or 14.2V, relative to jumper connection -
The APS-100 is 13.4V only) regardless of the load by varying output current
to compensate. AC input protection against damaging spikes of up to 190VAC
and brown-out input protection are also provided.
All APS Power Supplies feature an automatic, thermally triggered, current
controlled fan (APS-90 and APS-100 have two). When the internal circuitry
reaches a specified maximum operating temperature, the fan will turn on.
The speed of the fan will vary with current draw.
In an overcurrent condition (typically caused by use of an APS power Sup-
ply smaller than needed for a particular application), APS Models 75, 90 and
100 will automatically roll back current and voltage to prevent damage. Full
power will be restored when the overcurrent condition is corrected. If an
overcurrent condition is encountered with APS Models 15, 30, 45 and 55,
and high current draw causes voltage to drop to approximately 2V, the fuse
on the end panel of the power supply will blow. If the fuse blows repeatedly,
contact Cascade Audio for assistance.
All APS Power Supplies are protected against reverse-polarity connection
by use of internal diodes. If the outputs are connected in reverse, the fuse(s)
will blow to protect the unit.
Mounting
APS converter/power supplies can be mounted in any position. Allow suf-
ficient space to provide unrestricted airflow in and around the unit.
Note: Care must be taken to allow proper airflow when installing in an
enclosed compartment. Failure to provide proper airflow will result in poor
performance, or even product failure.
Never install electronics in a battery compartment or other area where
flammable fumes may exist, such as fuel storage areas.
Display Board Installation
Mount the power supply to allow use of short positive and negative cables.
Use power distribution blocks if necessary. Easy access to the main fuse
or circuit breaker should be considered as well.
2
Your new APS Power Supply can be used with or without an additional bat-
tery. Use of a battery connected in parallel with your APS power supply will
greatly increase the current available for transients. For installations where
use of a battery is not possible, capacitors may be used.
Vehicle Installation
Two methods of vehicle installation are commonly used. One is to mount
the positive and negative battery cables to the vehicle and to place the
power supply under the vehicle when necessary. Ease of connection is
accomplished through use of an additional quick-release type connector such
as that provided with our HK-4 Hook-up Kit (see illustration below).
The other method is to mount the power supply permanently into the vehicle.
In this installation, the power supply is hidden from view behind a panel in the
vehicle. A three prong male weatherproof recessed switchplate (available from
your local electrical supply house) can be mounted to the bottom of the
vehicle allowing use of a standard grounded outdoor extension cord to power
the unit. Installation of a manual-reset circuit breaker in the positive cable
between the power supply and the battery is recommended to prevent bat-
tery drain when the vehicle is stored for long periods of time without being
plugged-in.
DC Output Terminals
Before making any connections, be sure that the AC cord of your APS
Power Supply is unplugged. If installing a battery, disconnect the positive
side of the battery before installation.
Locate the two (2) screw terminals on
the end of the APS Power Supply la-
beled POS and NEG. (refer to the photo;
right)
3


Produktspezifikationen

Marke: Cascade Audio Engineering
Kategorie: Nicht kategorisiert
Modell: APS-15

Brauchst du Hilfe?

Wenn Sie Hilfe mit Cascade Audio Engineering APS-15 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Cascade Audio Engineering

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-