Carel MasterCase Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Carel MasterCase (60 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 26 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/60
MasterCase
User manual
We wish to save you time and money!
We can assure you that the thorough reading of this manual will guarantee correct installation and
safe use of the product described.
BEFORE INSTALLING OR HANDLING THE DEVICE PLEASE CAREFULLY READ AND FOLLOW THE
INSTRUCTIONS DESCRIBED IN THIS MANUAL.
This device has been manufactured to operate risk-free for its specific purpose, as long as:
it is installed, operated and maintained according to the instructions contained in this manual;
the environmental conditions and the voltage of the power supply correspond to those specified.
All other uses and modifications made to the device that are not authorised by the manufacturer are considered incorrect.
Liability for injury or damage caused by the incorrect use of the device lies exclusively with the user.
Please note that this unit contains powered electrical devices and therefore all service and maintenance operations must be
performed by specialist and qualified personnel who are aware of the necessary precautions.
Disconnect the machine from the mains power supply before accessing any internal parts.
Disposal of the parts of the controller:
The controller is made up of metal and plastic parts and contains a lithium battery. All these parts must be disposed of
according to the local standards in force.
General warnings - operating environments and connections
The following conditions represent correct installation:
1. do not install the instrument in environments with the following characteristics: wide and rapid fluctuations in ambient
temperature; temperature and relative over the allowed limit; exposure to direct pressurised jets of water; high levels of
magnetic and/or radio frequency interference (e.g. from transmitting antennae);
2. use cable ends suitable for the corresponding terminals. Loosen each screw and insert the cable ends, then tighten the screws.
When the operation is completed, slightly tug the cables to check that they are sufficiently tight;
3. separate as much as possible the signal cables from the cables carrying inductive loads and power cables to avoid possible
electromagnetic disturbance. Never insert power cables (including the electrical cables) and probe signal cables in the same
conduits. Do not install the probe cables in the immediate vicinity of power devices (contactors, circuit breakers or similar);
4. reduce the path of the probe cables as much as possible, and avoid spiral paths that enclose power devices. To extend the
probe cables, use cables with a minimum cross-section of at least 0.5mm2;
5. the cables connected to the contacts on the controller must be rated for the maximum operating temperature, determined by
considering the maximum room temperature envisaged, added to the heating up of the controller itself, equal to 20°C;
6. suitably protect the load power lines on the controller with devices (circuit breakers) rated according to the loads connected.
Safety for operators and precautions when handling the controller
To protect the safety of operators and safeguard the controller, before doing any work on the panel always disconnect the power
supply. Electrical damage may occur to the electronic components as a result of electrostatic discharges from the operator.
Suitable precautions must be therefore be taken when handling these components, specifically:
• before handling any controller, earth yourself (not touching the board does not prevent a spike, as a 10000V discharge, easily
reached with static electricity, can produce an arc of about 1cm);
• all materials must be kept inside their original package as long as possible. If necessary, take the controller from its package
and place it into an antistatic package without touching the rest of the controller with your hands;
• absolutely avoid non-antistatic plastic bags, polystyrene or sponges;
• do not pass the controller directly to other operators (to prevent from electrostatic induction and discharges).


Produktspezifikationen

Marke: Carel
Kategorie: Nicht kategorisiert
Modell: MasterCase

Brauchst du Hilfe?

Wenn Sie Hilfe mit Carel MasterCase benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Carel

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-