Caliber CA 110V4 Bedienungsanleitung
Caliber
Autolautsprecher
CA 110V4
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Caliber CA 110V4 (14 Seiten) in der Kategorie Autolautsprecher. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/14
CA 110.4
Ma x i m um Power Out put a t 1 4 ,4V
4Ω20Hz - 30kHz THD 1% 2x 330W
2Ω20Hz - 30kHz THD 1% 4x 165W
4Ω1kHz Mono Bridged 2x 330W
Co n t in u o us Power Ou t put a t 1 4 , 4V
4Ω20Hz - 30kHz THD 1% 4x 55W
2Ω20Hz - 30kHz THD 1% 4x 75W
4Ω1kHz Mono Bridged 2x 150W
Fus e Ra t ing 2x 20A
D i m en s io ns 310 x 260 x 55mm
Alle Caliber Performance versterkers hebben de volgen-
de technische gegevens. Technische gegevens die per
model verschillen zijn apart opgenomen.
Frequentierespons (+0, -1dB)20Hz-30kHz
Totale harmonische vervorming <0,05% (80kHz LPF)
Signaal-ruisverhouding (A-Weighted) 95dB
Ingangsgevoeligheid RCA-ingang 15V-500mV
Uitgangsimpedantie 2 - 8Ω
Low Pass/Full Range/High Pass Filter 50 - 250Hz
N E D E R L A N D S
Normal system set-up
Optional system set-up Optional system set-up
All Caliber Performance Amplifiers have the following
specifications.
Variable specifications are listed per model.
Frequency response (+0, -1dB)20Hz-30kHz
Total Harmonic Distortion <0,05% (80kHz LPF)
Signal to noise ratio (A-Weighted) 95dB
Input Sensitivity RCA input 15V-500mV
Output Impedance 2 - 8Ω
Low Pass/Full Range/High Pass Filter 50 - 250Hz
Folgende technische Daten sind vom alle Caliber
Performance gemeinsam.Abweichende Werte sind unter
den einzelnen Modellen aufgeführt.
Frequenzgang (+0, -1dB)20Hz-30kHz
Gesamtklirrfaktor <0,05% (80kHz LPF)
Rauschabstand (A-bewertet) 95dB
Eingangsempfindlichkeit Cinch-Eingang15V-500mV
Ausgangsimpedanz 2 - 8Ω
Tiefpass/Vollbereich/HochpassSchalter 50 - 250Hz
Alle Caliber Performance forsterkere har følgende spesi-
fikasjoner.
Variable spesifikasjoner listes opp for hver modell enkeltvis.
Frekvensrespons (+0, -1dB)20Hz-30kHz
Total harmonisk forvrengning <0,05% (80kHz LPF)
Forhold mellom signal og støy (A-vektet) 95dB
Inngangsfølsomhet RCA-inngang 15V-500mV
Utgangsimpedans 2 - 8Ω
Low Pass/Full Range/High Pass Filter 50 - 250Hz
Todos los amplificadores Caliber Performance tienen las
siguientes características.
Para cada modelo se indican las características variables.
Respuesta de frecuencia (+0, -1dB)20Hz-30kHz
Distorsión armónica total <0,05% (80kHz LPF)
Media señal-ruido (ponderada en A) 95dB
Entrada Input Sensitivity RCA 15V-500mV
Impedancia de salida 2 - 8Ω
Filtropaso bajo/Full Range/
Filtro paso alto 50 - 250Hz
Tous les amplificateurs Caliber Performance possèdent
les caractéristiques ci-dessous. Les caractéristiques variab-
les sont définies pour chaque modèle.
Réponse en fréquence (+0, -1dB)20Hz-30kHz
Distorsion harmonique totale <0,05% (80kHz LPF)
Rapport signal/bruit (pondéré A) 95dB
Sensibilité d'entrée Entrée Cinch 15V-500mV
Impédance de sortie 2 - 8Ω
Filtre passe-bas/Gamme complète/
Filtre Passe Haut 50 - 250Hz
Tutti gli amplificatori Performance della Caliber hanno le
seguenti specifiche tecniche.
Le specifiche tecniche variabili sono elencate per modello.
Risposta in frequenza (+0, -1dB)20Hz-30kHz
Distorsione armonica totale <0,05% (80kHz LPF)
Rapporto segnale/rumore (pesato 'A') 95dB
Sensibilità di ingresso RCA 15V-500mV
Impedenza di uscita 2 - 8Ω
Filtro passa basso/Full Range/ passa alto 50 - 250Hz
Todos os amplificadores Caliber Performance têm as
seguintes características.
Para cada modelo indicam-se as características variáveis.
Resposta de frequência (+0, -1dB)20Hz-30kHz
Distorção harmónica total <0,05% (80kHz LPF)
Média sinal-ruído (ponderada em A) 95dB
Entrada Input Sensitivity RCA 15V-500mV
Impedância de saída 2 - 8Ω
Passagem Baixa / Filtro de Gama
Completa / Passagem Alta 50 - 250Hz
E N G L I S H
E S P A Ñ O L P O R T U G U Ê S
S V E N S K
D E U T S C H I T A L I A N O
F R A N C A I S
4
E N G L I S H
3
E N G L I S H
2
R C A I N P U T
• Connect the RCA-outputs of your radio to the RCA input terminals of the amplifier.Take good care
that you connect the Right output of your radio to a Right input of your amplifier, and that you con-
nect the Left output of your radio to a Left input of your amplifier.
S I G N A L I N P U T
• The RCA’s to your left are the ‘Line-in’ terminals and are to be connected with your radio/cassette
or CD player.
• Each Caliber amplifier offers you the possibility to connect a second (or more) amplifier(s) to your
system via the “Signal-out” terminals. The advantage of two amplifiers is that one amplifier can be
used for normal stereo, while the other is used as a subwoofer amplifier.
• All Caliber amplifiers have a variable input level adjustment. It allows you to match any signal source
(CD player, AM/FM cassettedeck, etc) correctly from its pre-amp output into your Caliber amplifier.
The adjustment ranges from 15V - 500mV(0.5V).
• The Caliber Competition Series III amplifiers feature a built-in variable crossover which allows you
to fine-tune your amplifiers response as you like it. Either for the Full Range sound, in which case
the LPF-OFF-HPF switch remains in its OFF position, or you can specifically select the High-Pass-
Filter (HPF) or Low-Pass-Filter (LPF) to adjust to your speakers requirements.The built-in variable
crossover can be adjusted in a range from 50Hz - 250Hz.
S P E A K E R O U T P U T
• All the Caliber Performance amplifiers have Stereo/Bridgeable Tri-Mode speaker output terminals.
The amplifier has its own stereo/bridge switch built-in, so there is no need to select a stereo or
bridged mode. You can connect the speakers to each channel in stereo mode, and simultaneously
connect a sub-woofer to the speaker terminal in a bridged mode.
• Pay attention in connecting your speakers and/or sub-woofers. Be sure to obser ve correct speaker
output connections for front, rear and their polarity.
• In the stereo mode, connect the right speaker output to the right speaker and the left to the left.
Connect the positive (+) output to the positive (+) speaker terminal and the negative (-) output
to the negative (-) speakerterminal.
• In the bridged mode connect the left (+) positive to the positive speaker terminal and the right (-)
negative to the negative speaker terminal.
• Do not use the negative speaker output commonly for left and right speakers (common ground).
Improper polarity causes a loss of bass response.
• Never connect the negative speaker output to the chassis of your vehicle. This can cause severe
damage to your Car Audio System.
A M P L I F I E R A D J U S T M E N T S
• Put the input level adjustment knob to the minimum.
• Put the volume of your radio to 3/4 of the maximum.
• Adjust the Bass Boost to your personal sound.
• Now adjust the input level of the front channel. Slowly turn up the input level and listen carefully
untill you hear the amplifier begin to distort. A Caliber Amplifier “clips” ver y softly, so this can some-
times be a difficult adjustment. If you have turned up the Bass Boost to much, the amplifier will start
clipping immediatly. In that case you must turn back the Bass Boost and star t adjusting the inputle-
vel again.You will hear that the Bass you wanted can be required in this way.
C A L I B E R W A R R A N T Y
Due to the complexity of our products, we strongly recommend that this amplifier is installed by
your authorized Caliber dealer. If properly installed by your dealer we provide a warranty for 12
month from the date of purchase.
If you install this amplifier yourself, we wish you lots of fun and succes in doing so. If you follow our
guidelines, you’ll get the best result. Our warranty, however, will be limited to and not exceed 30
days from the date of purchase.
F E A T U R E S
• Bridgeable outputs.
• ’Tri-mode’ output capability, simultaneous stereo & bridged mono set up is possible.
• Pulse Width Modulated (PWM) MOSFET Power Supply.
• Balanced inputs
• Variable input sensitivity: RCA input 0,5V to 15V.
• Variable input sensitivity: High Level input
• BassBoost 0db / 6dB / 12dB
• Thermal-, Overload- and Shortcircuit protection.
• Excellent muting circuitr y assures no turn on/off ‘pops’.
• Built-in Full Range/Highpass/Low Pass Switch.
• Chromium plated power connectors for optimal power distribution.
• Chromium plated speaker connectors for optimal signal output.
• European design and engineering.
M O U N T I N G
The amplifier has to have at least 5 cm (2”) ventilation space at all sides, to allow the heat to rise
away from the amplifier. Be sure that the power and signal cables can enter and leave the amplifier
in a straight line, to avoid the risk of malfunction. Always place the power- and signalcables at
opposite sides of the vehicle to reduce any noises.
The amplifier should be protected from exposure to moisture and direct sunlight.
Mark the mounting surface using the amplifier as a template, then drill 2.5 mm (1/8”) diameter holes
at the marked locations and mount the amplifier using the supplied self-tapping screws.
I N S T A L L A T I O N
Remember to always disconnect battery ground before working on a vehicle’s electrical system!
Always place a fuse or circuit breaker no more than 30 cm (12”) from the battery, no greater than
the fuse(s) of your amplifier for optimal protection.
G E T T I N G Y O U R P O W E R S T A R T E D
• First, the +12V terminal is connected directly to the battery of your car. Use a cable of at least 10
mm2, and make sure that the connectors are of the same value.
- Don’t forget the extra “Vehicle protection” fuse.
- The 12V + terminal should NOT be connected to the car fuse box.
• Second, the ground terminal (GND) must be fastened securely to the chassis of the vehicle with the
same gauge cable as the positive cable (the same amount of power has to run through it). Ensure
that all paint, undercoating or any other insulation is removed from the area where you want to
make your ground connection to.
• Third, the last cable to connect is your remote turn-on (REM). Many radio-cassette and CD-players
have an output terminal for connection of the REM of an amplifier. If you don’t have such an out-
put, a separate switch must be installed to control your amplifiers on/off function.
S I G N A L I N P U T
The Caliber Performance Amplifiers offer you two possibilities for your signal input.
• A High Level input, using the loudspeaker output from your radio and the special High Level input-
plug you found in the box.
• Signal input by using a RCA cable from your radio’s RCA outputs to the amplifiers signal input RCA’s.
NEVER USE HIGH LEVEL INPUT AND RCA INPUT AT
THE SAME TIME!
H I G H L E V E L I N P U T
• Connect the loudspeaker outputs of your radio to the wires which are already on the special plug
you found in the box.
Take good care of the polarity (+ or -), and which signal is right or left.
L- = White, L + = White/Black R- = Gray, R + = Gray/Black GND = Black,connect to Ground.
Produktspezifikationen
| Marke: | Caliber |
| Kategorie: | Autolautsprecher |
| Modell: | CA 110V4 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Caliber CA 110V4 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Autolautsprecher Caliber
7 Oktober 2024
9 September 2024
8 September 2024
14 August 2024
1 August 2024
28 Juli 2024
27 Juli 2024
26 Juli 2024
24 Juli 2024
24 Juli 2024
Bedienungsanleitung Autolautsprecher
- Autolautsprecher Clatronic
- Autolautsprecher Exibel
- Autolautsprecher Philips
- Autolautsprecher Sony
- Autolautsprecher MarQuant
- Autolautsprecher Renkforce
- Autolautsprecher Blaupunkt
- Autolautsprecher Kenwood
- Autolautsprecher Autotek
- Autolautsprecher Pyle
- Autolautsprecher Auna
- Autolautsprecher Pioneer
- Autolautsprecher JBL
- Autolautsprecher JVC
- Autolautsprecher Hifonics
- Autolautsprecher Magnat
- Autolautsprecher ICES
- Autolautsprecher Alpine
- Autolautsprecher Renegade
- Autolautsprecher Rockford Fosgate
- Autolautsprecher Crunch
- Autolautsprecher AXTON
- Autolautsprecher Clarion
- Autolautsprecher Mac Audio
- Autolautsprecher ESX
- Autolautsprecher DNT
- Autolautsprecher Boss
- Autolautsprecher Hertz
- Autolautsprecher Kicker
- Autolautsprecher JL Audio
- Autolautsprecher DLS
- Autolautsprecher Dynex
- Autolautsprecher Emphaser
- Autolautsprecher Focal
- Autolautsprecher Fusion
- Autolautsprecher Infinity
- Autolautsprecher Lanzar
- Autolautsprecher Mtx Audio
- Autolautsprecher Radical Audio
- Autolautsprecher Rodek
- Autolautsprecher Soundstream
- Autolautsprecher AudioControl
- Autolautsprecher Metra
- Autolautsprecher Memphis Audio
- Autolautsprecher Aquatic AV
- Autolautsprecher SoundMAX
- Autolautsprecher Sinus Live
Neueste Bedienungsanleitung für -Kategorien-
15 Oktober 2024
14 Oktober 2024
14 Oktober 2024
10 Oktober 2024
8 Oktober 2024
7 Oktober 2024
7 Oktober 2024
2 Oktober 2024
2 Oktober 2024
30 September 2024