Bxterra BG350 Bedienungsanleitung

Bxterra UPS BG350

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Bxterra BG350 (2 Seiten) in der Kategorie UPS. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

INSTALLATION AND OPERATION

Introduction

Thank you for choosing a bXterra Uninterruptible Power Supply. This UPS system is ENERGY STAR®

certi ed and uses our GreenTech™ High-E ciency Design to consume less power, reduce heat and

improve UPS operation.

Inspection

Inspect your UPS upon purchase. The following items should be inside:

• UPS unit • User Manual • Telephone Cable

Remove the UPS from its package and inspect it for damage that may have occurred during shipping.

If any damage is discovered, re-pack the unit and return it to the place of purchase.

Determine the Power Requirements of Your Equipment

1. To determine the power requirements of your equipment, ensure that the equipment plugged

into the outlet does not exceed the UPS’s rated capacity. If the rated capacity of the unit is

exceeded, the UPS may overload and shut down or the circuit breaker may trip.

2. There are many factors that can a ect the amount of power that your equipment will require.

We suggest that the load placed on the battery outlets not exceed 80% of the UPS’s capacity.

Connect to Utility Power

This UPS must be plugged into utility power to charge its battery prior to initial use. The UPS will not

turn on right out of the box without plugging into an AC outlet  rst. This is a safety feature designed

to avoid the UPS from turning on during shipment. Connect the AC power cord of the UPS to utility

power. The UPS will start to charge its internal battery. When the UPS is plugged into an AC outlet, the

battery will automatically charge whether the UPS is turned on or not. This UPS should be charged for

eight hours prior to initial use for optimal performance.

Product Overview

1. Power button Used as the master on/o button for the UPS as well as

for equipment connected to the battery power supplied outlets.

2. Mute button Hold this button for more than one second to place the

unit in Silent Mode or silence the alarm.

3. AC input Connect the AC power cord of the UPS to utility power.

4. Circuit breaker This breaker provides overload and fault protection. If

it trips, remove some of the load then reset it by pressing it in.

5. Battery backup/Surge outlets These outlets provide battery backup

power and surge protection to connected devices.

6. Surge protected outlets These outlets protect connected equipment

in case of a power surge.

7. Phone surge protection These ports protect a single phone/modem/

fax line from surges.

8. Wiring Fault (Red) This LED indicates that a site wiring fault has

occurred.

Plug in Equipment

Battery Backup Outlets

With the UPS turned o and unplugged, connect equipment requiring battery backup to the “Surge &

Battery” outlets. These outlets provide battery backup, EMI/RFI  ltering and surge protection. Battery

power is automatically provided in case of power failure.

Surge Protected Outlets

Connect other devices requiring surge protection to the “Surge” outlets. These outlets do not provide

power during power failure.

DO NOT plug a laser printer, paper shredder, copier, space heater, vacuum cleaner, sump pump or

other large electrical device into the UPS. The power requirements of these devices will overload and

possibly damage the UPS.

Phone/Modem/Fax Line Protection

This UPS protects a single (1 in/1 out) phone/modem/fax line from surges. To use, connect a

telephone cable from the wall jack outlet to the IN jack of the UPS. Connect a telephone cable from

the OUT jack of the UPS to the telephone, modem or fax machine.

Turn the UPS On

To turn on the UPS, press the power button for at least two seconds. The LED indicators will light up.

If an overload is detected, the UPS will turn o and the unit will beep continuously. To  x this, turn the

UPS o and unplug at least one piece of equipment from the battery-power supplied outlets. Make

sure the Circuit Breaker button is depressed and turn the UPS on again. To turn o the UPS unit,

press the power button again. The LED light will turn o .

Note that “Surge Protection” outlets will power connected devices whether the UPS is on or oﬀ . “Surge +

Battery” protected outlets will power connected devices only when the UPS is on.

To store the UPS for an extended period of time, cover the unit and fully charge the battery before

disconnecting from AC power. While in storage, recharge the battery every three months to prolong

optimal battery life.

Note: For optimal battery charge, always leave the UPS plugged into the AC outlet.

LED Indicator Table

Power LED Alarm Wiring Fault Condition

On O O AC Mode

The UPS is functioning as intended.

Flashing every

10 seconds

Beeping

every 10

seconds

O Battery Mode

The UPS is providing power to its battery power-supplied out-

lets from the battery.

Flashing every

second

Beeping

every second

O Low Battery

The UPS is providing battery power. Rapid beeping indicates the

unit will run out of power shortly.

On Beeping

Continuously

O Overload

A continuous beeping occurs when connected equipment ex-

ceeds the listed capacity of the UPS. Turn the UPS o , unplug at

least one piece of equipment from the battery backup outlets,

reset the circuit breaker and turn the unit back on.

On/O None On Wiring Fault

This indicates a wiring problem with the AC input. This can be

a bad ground connection, a missing ground connection or

reversed wiring. Disconnect all electrical equipment from the

outlet and have an electrician check the outlet to insure proper

wiring.

O Beeping

every second

O Battery Low Shutdown Recovery

The unit is in a low battery shutdown state. It must be plugged

into utility power to charge.

WARRANTY & REGISTRATION

This bXterra product is constructed to provide unmatched power protection, quality and performance

for the duration of its lifetime. Please take a few minutes to register your new product at

bXterra.com/registration. Registration certi es your product’s warranty, con rms your ownership in

the event of a product loss or theft and entitles you to free technical support. Please register your

product now to receive the bene ts of bXterra ownership.

SAFETY

SAVE THESE INSTRUCTIONS: This manual contains important instructions that should be followed

during installation and maintenance of the UPS.

1. This unit is intended for installation in a controlled environment (a temperature-controlled and

indoor area free of conductive contaminants). Please avoid installing the UPS in locations where

there is standing or running water, dust, direct sunlight or excessive humidity.

2. This UPS utilizes voltage that may be hazardous. Do not attempt to disassemble the unit. The

unit contains no user-replaceable parts, including the battery. Only factory service personnel

may perform repairs.

3. Connect your UPS directly to a properly-grounded AC power outlet with fuse or circuit breaker

protection. Do not plug the unit into an outlet that is not grounded. Turn o and unplug the unit

if you need to de-energize it.

4. Not for use in a computer room as de ned in the Standard for the Protection of Electronic

Computer/Data Processing Equipment, ANSI/NFPA 75.

5. To reduce the risk of  re, connect only to a circuit provided with 20 amperes maximum branch

circuit over-current protection in accordance with the National Electric Code, ANSI/NFPA 70.

6. For best performance, keep the indoor temperature around the unit between 32⁰ F and 104⁰ F

(0⁰ C and 40⁰ C).

7. Do not attach medical equipment or non-computer related items, such as life-support

equipment, microwave ovens, or vacuum cleaners to the UPS. bXterra does not sell equipment

meant for life-support or medical applications. Visit our website for more information about

devices appropriate to plug into this UPS.

8. Only stand or set up the UPS in the direction speci ed in the Installation and Operation section

of this manual. Leave adequate space around all sides of the UPS for proper ventilation. Do not

expose the unit to direct sunlight and do not install the unit near heat-emitting appliances such

as a space heater or furnace. This could negatively impact the unit’s internal cooling system and

cause product damage not covered under warranty.

9. Do not plug the UPS input into its own output. Do not attach a power strip or surge protector to

the UPS.

10. Do not modify the UPS’s plug and do not use an adapter that would eliminate the UPS’s ground

connection.

11. Do not use extension cords to connect the UPS to an AC outlet.

12. If the UPS receives power from a motor-powered AC generator, the generator must provide

clean,  ltered, computer-grade output. Consult your generator’s manual to see if it meets these

speci cations.

13. The main power outlet that supplies the UPS should be easily accessible and near the UPS.

14. To reduce the risk of  re or electric shock, do not use the unit on any transportation such

as airplanes or ships. The e ect of shock or vibration caused during transit and the damp

environment can cause the unit to short out.

15. In the event of an emergency requiring the UPS or connected equipment to be turned o , press

the power button and disconnect the power cord from the AC power supply to properly disable

the UPS.

USER MANUAL

www.bxterra.com

BG STANDBY UPS

BG350

Plug in this device for to charge prior to initial use. 8 hours

To turn this UPS on or oﬀ , press & hold the power button for two seconds.

IMPORTANT

INFORMATIONS DE GARANTIE

Votre produit bXterra est livré avec une garantie limitée de 3 ans. bXterra garantit ce produit, s’il

est utilisé de manière appropriée et en conformité avec toutes les instructions applicables, d’être

exempt de tout vice de matériau et de fabrication pendant 3 ans à compter de la date d’achat initiale.

Si le produit peut présenter un défaut matériel ou de fabrication au cours de cette période de 3 ans,

bXterra, sous réserve des conditions et limitations de la garantie limitée du produit disponible sur

notre site Web, réparera ou remplacera ce produit. bXterra agira à sa seule discrétion comme seul

recours pour la violation de sa garantie limitée par bXterra. Vous trouverez tous les détails de cette

garantie limitée et de la garantie de l’équipement connecté de bXterra sur notre site Web à l’adresse

www.bxterra.com/warranty ou sur la page de chaque produit sur notre site Web. Veuillez enregistrer

votre produit sur www.bxterra.com/registration pour certier la garantie de votre produit.

CONSIGNES DE SÉCURITÉ

CONSERVEZ CES INSTRUCTIONS: Ce manuel contient des instructions importantes à suivre lors de

l’installation et de la maintenance de l’onduleur.

1. Cette unité est destinée à être installée dans un environnement contrôlé (zone à température

contrôlée et à l’intérieur exempte de contaminants conducteurs). Veuillez éviter d’installer l’on-

duleur dans des endroits où il y a de l’eau stagnante ou courante, de la poussière, de la lumière

directe du soleil ou une humidité excessive.

2. Cet onduleur utilise une tension qui peut être dangereuse. N’essayez pas de démonter l’unité.

L’unité ne contient aucune pièce remplaçable par l’utilisateur, y compris la batterie. Seul le per-

sonnel d’entretien de l’usine peut eectuer des réparations

3. Connectez votre onduleur directement à une prise de courant CA correctement mise à la terre

avec un fusible ou une protection de disjoncteur. Ne branchez pas l’appareil dans une prise qui

n’est pas mise à la terre. Éteignez et débranchez l’appareil si vous devez le mettre hors tension.

4. Ne pas utiliser dans une salle informatique telle que dénie dans la norme pour la protection

des équipements informatiques / de traitement de données, ANSI / NFPA 75.

5. Pour réduire le risque d’incendie, connectez uniquement à un circuit muni d’un circuit de déri-

vation de 20 ampères maximum sur protection de courant conformément au Code national de

l’électricité, ANSI / NFPA 70.

6. Pour de meilleures performances, maintenez la température intérieure autour de l’appareil

entre 32⁰ F et 104⁰ F (0⁰ C et 40⁰ C).

7. N’attachez pas d’équipement médical ou d’éléments non liés à l’ordinateur, tels que des équipe-

ments de survie, des fours à micro-ondes ou des aspirateurs à l’onduleur. bXterra ne vend pas

d’équipements destinés à des applications médicales ou de survie. Visitez notre site Web pour

plus d’informations sur les appareils appropriés pour se connecter à cet onduleur.

8. Placez ou congurez l’onduleur uniquement dans la direction spéciée dans la section Installa-

tion et utilisation de ce manuel. Laissez un espace susant sur tous les côtés de l’onduleur pour

une ventilation adéquate. N’exposez pas l’appareil à la lumière directe du soleil et n’installez pas

l’appareil à proximité d’appareils émettant de la chaleur, tels qu’un radiateur ou une fournaise.

Cela pourrait avoir un impact négatif sur le système de refroidissement interne de l’appareil et

causer des dommages au produit non couverts par la garantie.Ne branchez pas l’entrée de l’ASI

dans sa propre sortie. Ne xez pas une barrette d’alimentation ou un parasurtenseur à l’ondu-

leur.

9. Ne modiez pas la che de l’onduleur et n’utilisez pas d’adaptateur qui éliminerait la connexion

à la terre de l’onduleur.

10. N’utilisez pas de rallonges pour connecter l’onduleur à une prise secteur.

11. Si l’onduleur est alimenté par une génératrice à courant alternatif, le générateur doit fournir une

sortie propre, ltrée et de qualité informatique. Consultez le manuel de votre générateur pour

voir s’il répond à ces spécications.

12. La prise d’alimentation principale qui alimente l’onduleur doit être facilement accessible et

proche de l’onduleur.

13. Pour réduire le risque d’incendie ou d’électrocution, n’utilisez pas l’unité sur des moyens de

transport tels que des avions ou des navires. L’eet de choc ou de vibration causé pendant le

transport et dans l’environnement humide peut entraîner un court-circuit de l’unité.

En cas d’urgence nécessitant la mise hors tension de l’onduleur ou de l’équipement connecté,

appuyez sur le bouton d’alimentation et débranchez le cordon d’alimentation de l’alimentation

secteur pour désactiver correctement l’onduleur.

Troubleshooting

Problem Possible Cause Solutions

Power Button LED is

not on

The UPS is not on Press the power button for at least 2 seconds to turn on the UPS

The battery voltage is too low Charge the battery at least eight hours

Safety Start The unit must be connected to a 110/120V 50/60Hz outlet.

The battery is faulty Replace the battery

The UPS is always on

Battery Mode

The power cord is loose Plug in the power cord again

The UPS continuously

beeps

Please check the LED Indicator

Table for details

Please check the LED Indicator Table for details

The UPS will not turn on

The battery voltage is too low Charge the battery at least eight hours

There is an overload Remove some unnecessary loads. Before reconnecting equip-

ment, please verify that the load matches the UPS capabilities

detailed in the specications.

The battery is defective Contact support@bXterra.com for information about battery

replacement

GreenTech™ UPS High-Eciency Design

A highly-ecient bXterra GreenTech™ UPS can reduce your negative environmental impact and save

you money. By implementing high-quality components and leading-edge design, GreenTech™ UPS

systems strive to deliver improved UPS performance resulting in less energy waste and heat buildup.

RoHS Directive

We at bXterra want you to know that you’re not only protecting your devices and equipment when

purchasing a bXterra product, but you’re protecting the environment as well. Aside from being

ENERGY STAR® compliant, we are committed to and supporters of the Restriction of Hazardous

Substances (RoHS) directive, which strictly limits the use of six hazardous substances (lead, mercury,

cadmium, hexavalent chromium, polybrominated biphenyls (PBBs) and polybrominated diphenyl

ether (PBDE)) in electrical equipment.

FCC COMPLIANCE

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in an installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment

o and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment to an outlet on a dierent circuit than the one to which the receiver is

connected

• Consult an experienced radio/TV technician for help

WARNING: Changes or modications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

Specications

MODEL BG350

Topology Standby

INPUT

Voltage 120V

Frequency Range 50/60z ± 3Hz (Auto Sensing)

Input Voltage Range 90-145VAC

Circuit Breaker 10A 125/250VAC

Plug Type NEMA 5-15P

Plug Style Right Angle, 45o Oset

Power Cord 5 ft

OUTPUT

VA/W 350VA/255W

On Battery Voltage 120 VAC ± 5%

On Battery Frequency 50Hz/60Hz ± 1% (Auto Sensing)

On Battery Waveform Simulated Sine Wave

Outlet Type NEMA 5-15R

Outlets – Total 6

Outlets - Battery & Surge 3

Outlets - Surge-Only 3

Outlets - Widely Spaced 2

Overload Protection Internal Circuitry Limiting/Circuit Breaker

Transfer Time 4ms Typical

BATTERY

Runtime at Half Load(min) 6

Runtime at Full Load(min) 2

Battery Type Leakproof and maintenance-free sealed lead-acid battery

Battery Size 12V/2.9Ah

Recharge Time 8 Hours

SURGE PROTECTION & FILTERING

Surge Suppression 810 Joules

Phone RJ11 1-in/1-out

EMI/RFI Filtration Yes

MANAGEMENT & COMMUNICATION

LED Indicators Power On, AC Mode, Battery Mode, Fault

Audible Alarms On Battery, Low Battery, Overload, Fault

PHYSICAL

Form Factor Compact Desktop

Dimensions (in) 7.8 x 3.2 x 4.3

Weight (lbs) 3.5

ENVIRONMENTAL

Operating Temperature 32°F to 104°F (0°C to 40°C)

Operating Humidity 0% - 90% non-condensing

MODEL BG350

Maximum Operating Elevation 10,000 ft (3,000 m)

CERTIFICATIONS

Safety cTUVus (Conforms to UL1778 5th Edition & CSA 22.2 no. 107.3- 14 / R:

2014)/FCC DOC Class B/ENERGY STAR® certied

Environmental RoHS Compliant

Product specications are subject to change without prior notice

WARRANTY INFORMATION

Your bXterra product comes with a Limited 3-Year Warranty. bXterra warrants this product, if used

appropriately and in full accordance with all applicable instructions, to be free from original defects in

material and workmanship for 3 years from the date of initial purchase. If the product can be proven

defective in material or workmanship during that 3-year period, bXterra will, subject to the full terms

and limitations of the product’s Limited Warranty available on our website, repair or replace that

product. bXterra will act on its own discretion as the sole remedy for bXterra’s breach of its Limited

Warranty. Full details of this Limited Warranty and bXterra’s Connected Equipment Guarantee can

be found on our website at bxterra.com/warranty or at the individual product’s page on our website.

Please register your product at bxterra.com/registration to certify your product’s warranty.

Reserved. bXterra and the bXterra logo are trademarks of APX Power Technology LLC, USA. All other trademarks are

property of their respective owners. Imagery and specications may dier from actual products and are subject to

change without notice.

Produktspezifikationen

Marke:	Bxterra
Kategorie:	UPS
Modell:	BG350

Brauchst du Hilfe?

Wenn Sie Hilfe mit Bxterra BG350 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung UPS Bxterra

Bxterra SP3000LCDRT2U Bedienungsanleitung

30 August 2024

Bxterra BM1000AVRLCD Bedienungsanleitung

30 August 2024

Bxterra SP1500LCDRTXL2U Bedienungsanleitung

30 August 2024

Bxterra MODBUS-110 Bedienungsanleitung

30 August 2024

Bxterra SNMP-RC210 Bedienungsanleitung

30 August 2024

Bxterra BM850LCD Bedienungsanleitung

30 August 2024

Bxterra BG350 Bedienungsanleitung

30 August 2024

Bxterra BG450 Bedienungsanleitung

30 August 2024

Bxterra SP3000LCDRTXL2U Bedienungsanleitung

30 August 2024

Bxterra SP2200LCDRT2U Bedienungsanleitung

30 August 2024

Bedienungsanleitung UPS

Neueste Bedienungsanleitung für -Kategorien-

APC Back-UPS BN575G Bedienungsanleitung

13 Oktober 2024

APC Smart-UPS SMC1000-2UC Bedienungsanleitung

13 Oktober 2024

APC Back-UPS BX550CI-AR Bedienungsanleitung

13 Oktober 2024

APC Back-UPS BN600G Bedienungsanleitung

13 Oktober 2024

APC Back-UPS BX650CI-GR Bedienungsanleitung

13 Oktober 2024

APC Back-UPS BX950U-FR Bedienungsanleitung

13 Oktober 2024

APC Back-UPS BX650LI Bedienungsanleitung

13 Oktober 2024

APC Easy UPS BVX1000UXI Bedienungsanleitung

13 Oktober 2024

Eaton EX 3000VA 3U XL Bedienungsanleitung

11 Oktober 2024

Tripp Lite SmartOnline SV60KM3P4B Bedienungsanleitung

9 Oktober 2024