Blustream HMXL88 Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Blustream HMXL88 (8 Seiten) in der Kategorie Schalten. Dieser Bedienungsanleitung war fĂĽr 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/8
HMXL88
User Manual
HMXL88 USER MANUAL
02 www.blustream.co.uk
Surge protection device
recommended
This product contains sensitive electri-
cal components that may be damaged
by electrical spikes, surges, electric
shock, lightning strikes, etc. Use of
surge protection systems is highly
recommended in order to protect and
extend the life of your equipment.
Safety And
Performance Notice
The transmission distances of HDMI
over UTP cables are measured using TE
CONNECTIVITY 1427071-6
EIA/TIA-568-B termination (T568B) of
cables is recommended for optimal
performance.
To minimize interference of the un-
shielded twisted pairs in the CAT5e/6
cable do not run the HDBaseT /
Cat5e/6/6a cabling with or in close par-
allel proximity to mains power cables.
Do not substitute or use any other
power supply other than the enclosed
unit, or a Bluestream approved re-
placement.
Do not disassemble either the Trans-
mitter or Receiver units for any reason.
Doing so will void the manufacturer’s
warranty.
Introduction 03
Features 03
Panel Descriptions 03/04
EDID Control 04
Remote Control Descriptions 05
Specifications 05
Package Contents 05
RS-232 Pin Assignment 05
Maintenance 05
Application Diagram 06
RS-232 and Telnet Commands 07
Contents
Thank you for purchasing
this product.
For optimum performance and safety,
please read these instructions care-
fully before connecting, operating or
adjusting this product. Please keep this
manual for future reference.
HMXL88 USER MANUAL
03
contact support@blustream.co.uk / support@blustream.com.au
Our essential 8x8 HDBaseT™ Matrix oers unprecedented performance
and value for the custom installation market. The HMXL88 is a 4K UHD 8x8
matrix with a combination of 6 x HDBaseT™ and 2 x HDMI outputs. This al-
lows for cost-eective integration of local displays or AV receivers within an
installation. The matrix delivers HDMI, Bi-directional IR and PoH (PoE) up to
lengths of 70m over a single CAT cable. It can also be seemlessly controlled
by 3rd party control systems via RS-232 or TCP/IP.
Introduction
Front Panel
FEATURES:
• Features 8x HDMI inputs which
can be independantly routed
to 6x HDBaseT™ outputs and 2x
independent HDMI outputs
• Extends HDMI up to a distance of
70m over single CAT cable
• Supports 4K UHD video up to 40m
(3840 x 2160 @30Hz 4:4:4, 4096 x 2160
@24Hz 4:4:4, and 4K @60Hz 4:2:0)
• Supports all industry standard video
resolutions including VGA-WUXGA
and 480i-4K
• Supports 3D signal display
• Supports all known HDMI audio
formats including Dolby TrueHD,
Dolby Atmos, Dolby Digital Plus and
DTS-HD Master Audio transmission
• Supports bi-directional IR from all
input and output locations
• Control via front panel, IR, RS-232
and TCP/IP
• Supports PoH (Power over
HDBaseT™) to power compatible
HDBaseT™ receivers
• 3rd Party drivers available for all
major home control brands
• Advanced EDID management
• HDCP compliant
• 1U Design for 19” rack mount
integration - mounting kit included
1 2 4
11
5
12
6
13
7
14
8
15
9
16
3
10
1 LCD display – Show the status of
input-output selection, menu and
EDID info.
2 IR receiver window – Receives IR
from a hand held remote control or
processor.
3 Power LED indicator – Indicates the
power status of the matrix.
4 Power button – Press to toggle the
power of the matrix on/o.
5 HDMI output selection button 1 to
8 – Press to select the output from
1 to 8.
6 All button for HDMI outputs – Press to
select all of the outputs from 1 to 8.
7 Menu button – Press to enter EDID
setup mode. Three EDID segments
will display on the LCD panel listed
as: INPUT, VIDEO and AUDIO, for
example: IN1 1080P 2.0CH, means
to set 1080P 2.0CH EDID to INPUT1.
The blinking segment is the adjust-
able parameter.
8 Up – Press to change up through
the adjustable values.
9 ESC – Press to quit EDID setup
menu.
q Lock LED indicator – Indicate the
status of the key lock.
w Lock button – Press to lock the but-
tons on the front panel.
e HDMI input selection button 1 to 8 –
Press to select the input from
1 to 8.
r PTP – Press to mirror all inputs and
outputs (e.g. output 1 to input 1,
output 2 to input 2 and so on).
t Select – Press to select an EDID
parameter to change. Selected seg-
ment will blinking.
y Down – Press to change down
through the adjustable values.
u Enter – Press to set EDID to speci-
fied INPUT or copy EDID from speci-
fied OUTPUT to specified INPUT.


Produktspezifikationen

Marke: Blustream
Kategorie: Schalten
Modell: HMXL88

Brauchst du Hilfe?

Wenn Sie Hilfe mit Blustream HMXL88 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Schalten Blustream

Bedienungsanleitung Schalten

Neueste Bedienungsanleitung fĂĽr -Kategorien-