Best PM6 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Best PM6 (12 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/12
Page 1
Model PF6
FLEX BLOWER
WARNING
READ AND SAVE THESE INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR IN-
JURY TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer.
If you have questions, contact the manufacturer at the address
or telephone number in the warranty.
2. Before servicing or cleaning unit, switch power off at service
panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by a
qualified person(s) in accordance with all applicable codes
and standards, including fire-rated construction codes and
standards.
4. Sufficient air is needed for proper combustion and exhausting
of gases through the flue (chimney) of fuel burning equip-
ment to prevent backdrafting. Follow the heating equipment
manufacturer’s guideline and safety standards such as those
published by the National Fire Protection Association (NFPA),
and the American Society for Heating, Refrigeration and Air
Conditioning Engineers (ASHRAE), and the local code au-
thorities.
5. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. To reduce the risk of fire, use only metal ductwork.
8. This unit must be grounded.
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
a) Never leave surface units unattended at high settings.
Boilovers cause smoking and greasy spillovers that may
ignite. Heat oils slowly on low or medium settings.
b) Always turn hood ON when cooking at high heat or when
cooking flaming foods.
c) Clean ventilating fans frequently. Grease should not be
allowed to accumulate on fan or filter.
d) Use proper pan size. Always use cookware appropriate
for the size of the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE
EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE
FOLLOWINGa:
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or
metal tray, then turn off the burner. BE CAREFUL TO
PREVENT BURNS. If the flames do not go out immedi-
ately, EVACUATE AND CALL THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN - You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels - a
violent steam explosion will result.
4. Use an extinguisher ONLY if:
A. You know you have a Class ABC extinguisher, and you
already know how to operate it.
B. The fire is small and contained in the area where it
started.
C. The fire department is being called.
You can fight the fire with your back to an exit.D.
a
Based on “Kitchen Firesafety Tips” published by NFPA.
CAUTION
1. For indoor use only.
2. For general ventilating use only. Do not use to exhaust haz-
ardous or explosive materials and vapors.
3. To avoid motor bearing damage and noisy and/or unbalanced
impellers, keep drywall spray, construction dust, etc. off power
unit.
4. Clean filters and grease-laden surfaces frequently.
5. Do not repair or replace any part of this appliance unless
specifically recommended in this manual. All other servicing
should be done by a qualified technician.
6. Please read specification label on product for further information
and requirements.
7. To reduce the risk of fire and electric shock, install this blower
only with downdraft ventilator models shown below. Other
downdraft ventilator models cannot be substituted. (Downdraft
ventilators sold separately).
BEST
®
Models
D49M30SB, D49M36SB, D49M48SB
For use with these Downdraft Ventilators:
BEST® Models D49M30SB, D49M36SB,
D49M48SB
(Purchase Downdraft Ventilator separately.)
!
INSTALLER: Save this manual for Electrical Inspector and Homeowner to use.
Register your product online at: www.BestRangeHoods.com
Page 2
Model PF6
PLAN THE INSTALLATION
If you choose to mount the Flex Blower directly to the Downdraft
housing: Remove the inlet cover (taped in place for shipping)
and discard inlet cover. Refer to installation instructions in the
Downdraft manual.
If you choose to mount the Flex Blower in a remote location,
(such as the cabinet back, cabinet side, or floor joists) - follow
the instructions below.
INSTALL FLEX BLOWER
IN REMOTE LOCATION
NOTE: THE FLEX BLOWER MUST BE INSTALLED WITHIN
4-FEET OF THE DOWNDRAFTS ELECTRICAL PANEL.
The Electrical Panel can be mounted directly to the Downdraft
housing - or mounted in a remote location (always within 4-feet
of the Flex Blower).
1. Position inlet cover over blower wheel. Securely attach the
inlet cover to the blower with 8 screws and 8 nuts from parts
bag. Note that inlet cover is taped to blower for shipping. This
tape may be removed.
2. Determine how the 8” round and ductwork INLET OUTLET
will connect to the Flex Blower.
3. Remove the necessary 1/4-20 x .50 hex head screws and attach
4 MOUNTING BRACKETS to the Flex Blower - using 4 of the
6 POSSIBLE BRACKET MOUNTING LOCATIONS.
4. Mount Flex Blower to back of cabinet, floor joist, or adequate
framework (constructed by installer) with appropriate
MOUNTING SCREWS (not included).
5. Connect 8 ROUND DUCT from Downdraft housing to Flex
Blower inlet and from Flex Blower outlet to roof or wall cap.
For best performance: Choose the ducting option which allows
the shortest length of ductwork and a minimum number of
elbows and transitions. Check location of floor joists, wall
studs, electrical wiring or plumbing for possible interference.
6. Use strain relief bushing (provided) to attach Flex Blower wiring
to wiring box on Downdraft’s electrical panel and make wiring
connections. (See Downdraft manual for instructions.)
INLET
(from downdraft)
OUTLET
(to roof cap
or wall cap)
(6) MOUNTING
BRACKET
LOCATIONS
8-IN.
ROUND
DUCT
(to roof cap
or wall cap)
8-IN.
ROUND
DUCT
(from
downdraft)
MOUNTING SCREWS
(not included)
(4) MOUNTING
BRACKETS
attached with
1/4-20 X .50
HEX HEAD
SCREWS
CONTENTS
These parts are included with your Flex Blower:
2 - blower mounting legs*
1 - Parts Bag containing:
(4) wood screws #10 x .50*
(4) blower mount brackets
(1) strain relief bushing
(8) screws #10 x .38
(8) nuts #10
* For use when mounting Flex Blower directly to Downdraft
housing. (See Downdraft instruction manual.)
BLOWER
INLET
COVER
Page 3
Model PF6
1
2
3
4
56
7
89
10
11
SERVICE PARTS
KEY DESCRIPTION QTYPART
NUMBERNO.
1 97020267 Inlet Cover - including: 1
8 screws, #10 x 3/8
8 nuts, #10
2 97017924 Blower (complete) 1
(includes key nos. 7-11 & Hardware Bag)
+ 97018828 Hardware Bag - containing: 1
1 retaining ring
4 grommets
4 screws, M4 x 16.8mm
3 screws, M4 x 0.7 x 16mm
1 screw, M4 x 0.7 x 12mm
3 97020266 Blowerbox End - Blower Mount 1
(includes strain relief)
4 99271511 1Wire Harness
(includes strain relief)
5 98011179 2Blower Mounting Legs
6 97020268 Parts Bag - containing: 1
4 blower mounting brackets
4 wood screws, #10 x .50
1 strain relief bushing
8 screws, #10 x .38
8 nuts, #10
10 screws, 1/4 x .50
7 99111448 Blower Housing, Motor 1
8 99111447 1Blower Housing, Inlet
9 99271379 Capacitor 1
110 99020298 Blower Wheel
111 99080629 Motor
+ Not Shown


Produktspezifikationen

Marke: Best
Kategorie: Nicht kategorisiert
Modell: PM6

Brauchst du Hilfe?

Wenn Sie Hilfe mit Best PM6 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Best

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-