Benro HD3A Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Benro HD3A (2 Seiten) in der Kategorie Stativ. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/2
75 Virginia Road
North White Plains, NY 10603
T 914.347.3300
F 914.347.3309
info@BenroUSA.com
BenroUSA.com
HD Series 3-Way Panhead
Operating Instructions
Thank you for making Benro your choice for professional photographic
equipment. Your Benro gear is manufactured to provide years of
dependable service. In order to obtain optimum satisfaction and
performance, we suggest that you carefully read these instructions.
Specifications and design are subject
to change without notice.
1 2
Quick Release Plate
Horizontal Tilt Lock
Plate Locking Lever
Pan Lock
Base
Mounting Screw
Front/Rear Tilt Lock
Security Locking Lever
Bubble Level
SETUP
Head Mounting
Install by screwing the head clockwise onto
the 3/8" Mounting Thread of the Top Plate of
the Tripod or Monopod. Once it is hand tight,
secure by fully tightening the Head Locking
Screw(s) (on select models) from below.
OPERATION
Three-way positioning of camera and
lens movement is directly controllable
on the HD Series 3-Way Panheads. Two
comfortable Handles provide both
movement and locking of front to rear
Tilt, and side to side Tilt. Plus, a separate
Locking Knob permits the entire Head
assembly to move freely within a 360°
rotational adjustment.
Quick Release Plate
The HD Series 3-Way Panheads incorporate
a Quick Release Plate system. It offers a
quick method of mounting or releasing a
Camera or Equipment from the Head. It’s
important that the correct Quick Release
Plate be used along with the proper
mounting screw (1/4–20 is included as the
standard size but spare 1/4–20 and 3/8
plates are available as accessories). Extra
Plates are recommended as you can screw
one to each Camera or Lens for even greater
convenience when rapidly mounting and
dismounting gear.
Quick Release Locking Lever (FIGURES 1 & 2)
When used properly, the patented Dual
Lock Quick Release system offers two levels
of security for your gear. To remove the
Quick Release Plate, squeeze both the Plate
Locking Lever and the Security Locking
Lever and pull the larger Locking Lever
out. The Quick Release Plate will disengage
allowing it to be removed.
To reconnect the Quick Release Plate, insert
the angled part of the Plate into the groove
on the opposite side of the Locking Levers
and press down flat. The Locking Levers will
automatically engage the locking system and
will return to the safety lock position. Press
the Plate Locking Lever in firmly to secure.
Pan Control (FIGURE 3)
Horizontal rotation or Panning can be easily
accomplished by first loosening the Pan Lock
and then rotating Head on Platform. Once
in position tighten the Pan Lock securely.
NOTE: Do not over tighten the Pan Lock as
this could damage the locking mechanism.
Tilt Control (FIGURE 4)
Front to Rear Angle or Tilt adjustments can
be easily accomplished by first loosening
the Tilt Lock (be sure to hold on firmly to
balance weight of the camera). Position as
required and then tighten Handle securely.
You have the same Control and Lock
available on the other axis for Horizontal
Angle or Tilt adjustments.
NOTE: Do not over tighten the Tilt Locks as
this could damage the locking mechanism.
FOR ADDITIONAL CONTROL: Depending
on your requirements you may find it
convenient to reorient the camera or lens
90° on the Quick Release Plate and remount
so that the Tilt Controls give you different
positioning support.
USER NOTICE
• Do not exceed the maximum specified
load capacity (see specifications at
www.BenroUSA.com).
• Always ensure that all Panhead locks are
tightly engaged before mounting any gear.
• Always clean and dry any Panhead after
it has been exposed to wet, dusty, sandy
or salty conditions. Your Panhead is not
recommended for use in salt water. If
required, clean Panhead using a mild
soap solution applied with a soft cloth,
rinse with fresh water and dry with soft
towel. Remove any dust, dirt or sand from
all locks and all moving parts.
• Do not leave any Panhead in the sun
for prolonged periods and avoid high
temperature exposure.
• Avoid leaving any Tripod or Monopod
unattended in areas where people could
trip over the gear and get hurt.
• Remove camera, lens, and all gear from any
Tripod or Monopod when transporting.
• For your safety, don’t let your Benro
gear come in contact with any electrical
power source.
3 4
Operating Instructions & User Notice
Produktspezifikationen
| Marke: | Benro |
| Kategorie: | Stativ |
| Modell: | HD3A |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Benro HD3A benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Stativ Benro
8 Oktober 2024
3 Oktober 2024
20 September 2024
8 September 2024
4 September 2024
1 September 2024
3 August 2024
3 August 2024
2 August 2024
2 August 2024
Bedienungsanleitung Stativ
- Stativ Hama
- Stativ SilverCrest
- Stativ Sony
- Stativ Trust
- Stativ Panasonic
- Stativ Laserliner
- Stativ Velleman
- Stativ Bresser
- Stativ König
- Stativ Ryobi
- Stativ Braun
- Stativ Pyle
- Stativ Livoo
- Stativ Garmin
- Stativ Kessler
- Stativ Swarovski
- Stativ Marshall Electronics
- Stativ Cullmann
- Stativ Carson
- Stativ DJI
- Stativ AVerMedia
- Stativ Kodak
- Stativ Easypix
- Stativ Rollei
- Stativ Eurolite
- Stativ Testo
- Stativ Kogan
- Stativ GoPro
- Stativ Davis
- Stativ Celestron
- Stativ Levenhuk
- Stativ Joby
- Stativ Manfrotto
- Stativ Vortex
- Stativ Sachtler
- Stativ GVM
- Stativ ARRI
- Stativ Zhiyun
- Stativ Rode
- Stativ Dörr
- Stativ Drift
- Stativ Neewer
- Stativ Ravelli
- Stativ Revo
- Stativ Sunpak
- Stativ Vanguard
- Stativ Velbon
- Stativ Winegard
- Stativ 3 Legged Thing
- Stativ Sky-Watcher
- Stativ Proaim
- Stativ Celly
- Stativ Gitzo
- Stativ Miller
- Stativ Vello
- Stativ Induro
- Stativ Magnus
- Stativ Ulanzi
- Stativ Konig & Meyer
- Stativ Libec
- Stativ Glide Gear
- Stativ Slik
- Stativ Oben
- Stativ Vinten
- Stativ Gravity
- Stativ Block & Block
- Stativ Barska
- Stativ Ultimate Support
- Stativ IFootage
- Stativ FeiYu-Tech
- Stativ Easyrig
- Stativ Sirui
- Stativ FeiyuTech
- Stativ On Air
- Stativ Moza
- Stativ IOptron
- Stativ SteadiCam
- Stativ Hohem
- Stativ FLOWCINE
- Stativ Sevenoak
- Stativ Camgear
- Stativ Flycam
- Stativ Acratech
- Stativ ProMediaGear
- Stativ Fidlock
- Stativ Mantona
- Stativ Olloclip
- Stativ SmallRig
- Stativ MOVE'N SEE
- Stativ Kaiser Fototechnik
- Stativ Slidekamera
- Stativ Fat Gecko
- Stativ FLM
- Stativ Peak Design
- Stativ Robus
- Stativ Studio Assets
- Stativ Square Jellyfish
- Stativ Stalco
- Stativ Tiltall
- Stativ E-Image
Neueste Bedienungsanleitung für -Kategorien-
2 Oktober 2024
24 September 2024
22 September 2024
18 September 2024
14 September 2024
14 September 2024
7 September 2024
6 September 2024
6 September 2024
6 September 2024