Benro BH00 Bedienungsanleitung

Benro Stativ BH00

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Benro BH00 (2 Seiten) in der Kategorie Stativ. Dieser Bedienungsanleitung war für 35 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
BH Series Single-Action Ballheads
75 Virginia Road
North White Plains, NY 10603
T 914.347.3300
F 914.347.3309
info@BenroUSA.com
BenroUSA.com
Operating Instructions
Thank you for making Benro your choice for professional photographic
equipment. Your Benro gear is manufactured to provide years of
dependable service. In order to obtain optimum satisfaction and
performance, we suggest that you carefully read these instructions.
Specifications and design are subject
to change without notice.
Camera Screw
Quick Release Plate
Bubble Level
Base
Plate Locking Lever
Ball Locking Lever
Security
Locking Lever
Mounting Platform
Head Mounting
Install by screwing the head clockwise onto
the 3/8" Mounting Thread of the Top Plate of
the Tripod or Monopod. Once it is hand tight,
secure by fully tightening the Head Locking
Screw(s) (on select models) from below.
OPERATION
The single-action Ball Locking Lever
controls all movements of the BH Series
Ballheads. When released, the Ballhead and
the Mounting Platform can move freely
within a 360° rotational adjustment. And
two U-shaped openings on opposite sides
provide 90° angular movement of the
Mounting Platform.
Quick Release Plate
The BH Series Single-Action Ballheads
incorporate a Quick Release Plate system.
It offers a quick method of mounting or
releasing a Camera or Equipment from the
Head. It’s important that the correct Quick
Release Plate be used along with the proper
mounting screw (1/4–20 is included as the
standard size but spare 1/4–20 and 3/8
plates are available as accessories). Extra
Plates are recommended as you can screw
one to each Camera or Lens for even greater
convenience when rapidly mounting and
dismounting gear.
Quick Release Locking Lever
(FIGURES 1, 2 & 3)
When used properly, the patented Dual
Lock Quick Release system offers two levels
of security for your gear. To remove the
Quick Release Plate, squeeze both the Plate
Locking Lever and the Security Locking
Lever and pull the larger Locking Lever
out. The Quick Release Plate will disengage
allowing it to be removed.
To reconnect the Quick Release Plate, insert
the angled part of the Plate into the groove
on the opposite side of the Locking Levers
and press down flat. The Locking Levers will
automatically engage the locking system and
will return to the safety lock position. Press
the Plate Locking Lever in firmly to secure.
Ball Locking Lever (FIGURE 4)
The single-action Ball Locking Lever is
spring-loaded and can be repositioned when
it is in the lock position to accommodate
any desired Lever position. To reposition,
gently pull on the Lever to disengage, and
then allow the spring to pull the lever back
to reengage.
NOTE: Do not over tighten the Locking
Lever as this could damage the Ballhead
locking mechanism.
1 2
3
360°
180°
4
• Do not exceed the maximum specified
load capacity (see specifications at
www.BenroUSA.com).
• Always ensure that all Ballhead locks are
tightly engaged before mounting any gear.
• Always clean and dry any ballhead after
it has been exposed to wet, dusty, sandy
or salty conditions. Your Ballhead is not
recommended for use in salt water. If
required, clean Ballhead using a mild
soap solution applied with a soft cloth,
rinse with fresh water and dry with soft
towel. Remove any dust, dirt or sand from
all locks and all moving parts.
• Do not leave any Ballhead in the sun
for prolonged periods and avoid high
temperature exposure.
• Avoid leaving any Tripod or Monopod
unattended in areas where people could
trip over the gear and get hurt.
• Remove camera, lens, and all gear from any
Tripod or Monopod when transporting.
• For your safety, don’t let your Benro
gear come in contact with any electrical
power source.
USER NOTICESETUP
Operating Instructions & User Notice


Produktspezifikationen

Marke: Benro
Kategorie: Stativ
Modell: BH00

Brauchst du Hilfe?

Wenn Sie Hilfe mit Benro BH00 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Stativ Benro

Bedienungsanleitung Stativ

Neueste Bedienungsanleitung für -Kategorien-