Benro B3 Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Benro B3 (2 Seiten) in der Kategorie Stativ. Dieser Bedienungsanleitung war für 32 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/2
B Series Double-Action Ballheads
75 Virginia Road
North White Plains, NY 10603
T 914.347.3300
F 914.347.3309
info@BenroUSA.com
BenroUSA.com
Operating Instructions
Thank you for making Benro your choice for professional photographic
equipment. Your Benro gear is manufactured to provide years
of dependable service. In order to obtain optimum satisfaction and
performance, we suggest that you carefully read these instructions.
Specifications and design are subject
to change without notice.
Mounting Screw
Stop Screws (2)
Head Locking Knob
Mounting Screw
Mounting Platform
Bubble Level
SETUP
Head Mounting
Install by screwing the head clockwise onto
the 3/8" Mounting Thread of the Top Plate of
the Tripod or Monopod. Once it is hand tight,
secure by fully tightening the Head Locking
Screw(s) (on select models) from below.
OPERATION
The B Series Double-Action Ballheads are
professional black anodized machined
aluminum and feature three operating
Knobs. Drag control is manually adjusted
and locked, along with independent
Panning. Plus a Universal Quick Release
Clamp with secondary Safety Lock System
is incorporated.
Universal Quick Release Plate System
The B Series Double-Action Ballheads
feature a Universal Quick Release Plate
system. It offers a quick method of
mounting or releasing a Camera or
Equipment from the Head. It’s important
that the correct Quick Release Plate be used
along with the proper mounting screw
(1/4–20 is included as the standard size
but spare 1/4–20 and 3/8 plates of various
lengths are available as accessories). Extra
Plates are recommended as you can screw
one to each Camera or Lens for even greater
convenience when rapidly mounting
and dismounting gear. And because of
compatibility with the Universal system,
most plates and special brackets from other
manufacturers can be used as well.
Quick Release Lock (FIGURE 1)
When used properly, the Quick Release
Lock offers two levels of security for your
gear. To remove the Quick Release Plate,
turn the Quick Release Locking Knob
counter-clockwise. A partial opening of
the clamping mechanism allows the Quick
Release Plate to slide on the Mounting
Platform for proper balance and positioning.
Two Stop Screws (removable) on the bottom
of the Quick Release Plate provide this first
level of security. An additional counter-
clockwise turn of the Quick Release Locking
Knob opens the clamp fully so that the
Quick Release Plate can be tilted out to
be removed. Reverse the process and
tighten the Quick Release Locking Knob
to secure the Quick Release Plate.
Ballhead Controls (FIGURE 2)
A large Head Locking Knob locks the
Ballhead in place. Once the Knob is
turned counter-clockwise and loosened,
the Ballhead can move freely allowing
the Mounting Platform to be positioned
anywhere within a 0–90° vertical
orientation. This movement is expanded by
the use of the Pan Locking Knob
which adds a 360° Panning range. The Pan
control is fully independent and positioning
can be adjusted easily and accurately by
using the Graduated Panning Scale and
Pointer on the Base of the Ballhead.
When the Head Locking Knob is released,
it is possible to move the Ballhead with
some resistance or Drag. To achieve the
proper degree of Drag, mount the intended
camera or equipment onto the Ballhead.
While holding the camera/lens loosen the
Head Locking Knob until it is released.
Turn the Drag Control Knob clockwise to
increase Drag, and counter-clockwise to
decrease it.
FOR OPTIMUM RESULTS: Adjust the Drag
under the weight capacity, temperature
and conditions under which the Ballhead
will be used.
NOTE: Do not over tighten any Locking
Knobs as this could damage the Ballhead
locking mechanism.
USER NOTICE
• Do not exceed the maximum specified
load capacity (see specifications at
www.BenroUSA.com).
• Always ensure that all Ballhead locks are
tightly engaged before mounting any gear.
• Always clean and dry any Ballhead after
it has been exposed to wet, dusty, sandy
or salty conditions. Your Ballhead is not
recommended for use in salt water. If
required, clean Ballhead using a mild
soap solution applied with a soft cloth,
rinse with fresh water and dry with soft
towel. Remove any dust, dirt or sand from
all locks and all moving parts.
• Do not leave any Ballhead in the sun
for prolonged periods and avoid high
temperature exposure.
• Avoid leaving any Tripod or Monopod
unattended in areas where people could
trip over the gear and get hurt.
• Remove camera, lens, and all gear from any
Tripod or Monopod when transporting.
• For your safety, don’t let your Benro
gear come in contact with any electrical
power source.
Drag Control Knob
Base
Pan Locking Knob
Quick Release
Locking Knob
1
2
Panning
Scale Pointer
360°
Operating Instructions & User Notice
Produktspezifikationen
| Marke: | Benro |
| Kategorie: | Stativ |
| Modell: | B3 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Benro B3 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Stativ Benro
8 Oktober 2024
3 Oktober 2024
20 September 2024
8 September 2024
4 September 2024
1 September 2024
3 August 2024
3 August 2024
2 August 2024
2 August 2024
Bedienungsanleitung Stativ
- Stativ Hama
- Stativ SilverCrest
- Stativ Sony
- Stativ Trust
- Stativ Panasonic
- Stativ Laserliner
- Stativ Velleman
- Stativ Bresser
- Stativ König
- Stativ Ryobi
- Stativ Braun
- Stativ Pyle
- Stativ Livoo
- Stativ Garmin
- Stativ Kessler
- Stativ Swarovski
- Stativ Marshall Electronics
- Stativ Cullmann
- Stativ Carson
- Stativ DJI
- Stativ AVerMedia
- Stativ Kodak
- Stativ Easypix
- Stativ Rollei
- Stativ Eurolite
- Stativ Testo
- Stativ Kogan
- Stativ GoPro
- Stativ Davis
- Stativ Celestron
- Stativ Levenhuk
- Stativ Joby
- Stativ Manfrotto
- Stativ Vortex
- Stativ Sachtler
- Stativ GVM
- Stativ ARRI
- Stativ Zhiyun
- Stativ Rode
- Stativ Dörr
- Stativ Drift
- Stativ Neewer
- Stativ Ravelli
- Stativ Revo
- Stativ Sunpak
- Stativ Vanguard
- Stativ Velbon
- Stativ Winegard
- Stativ 3 Legged Thing
- Stativ Sky-Watcher
- Stativ Proaim
- Stativ Celly
- Stativ Gitzo
- Stativ Miller
- Stativ Vello
- Stativ Induro
- Stativ Magnus
- Stativ Ulanzi
- Stativ Konig & Meyer
- Stativ Libec
- Stativ Glide Gear
- Stativ Slik
- Stativ Oben
- Stativ Vinten
- Stativ Gravity
- Stativ Block & Block
- Stativ Barska
- Stativ Ultimate Support
- Stativ IFootage
- Stativ FeiYu-Tech
- Stativ Easyrig
- Stativ Sirui
- Stativ FeiyuTech
- Stativ On Air
- Stativ Moza
- Stativ IOptron
- Stativ SteadiCam
- Stativ Hohem
- Stativ FLOWCINE
- Stativ Sevenoak
- Stativ Camgear
- Stativ Flycam
- Stativ Acratech
- Stativ ProMediaGear
- Stativ Fidlock
- Stativ Mantona
- Stativ Olloclip
- Stativ SmallRig
- Stativ MOVE'N SEE
- Stativ Kaiser Fototechnik
- Stativ Slidekamera
- Stativ Fat Gecko
- Stativ FLM
- Stativ Peak Design
- Stativ Robus
- Stativ Studio Assets
- Stativ Square Jellyfish
- Stativ Stalco
- Stativ Tiltall
- Stativ E-Image
Neueste Bedienungsanleitung für -Kategorien-
2 Oktober 2024
24 September 2024
22 September 2024
18 September 2024
14 September 2024
14 September 2024
7 September 2024
6 September 2024
6 September 2024
6 September 2024