Bellman Visit Bedienungsanleitung
Bellman
Beveiliging
Visit
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Bellman Visit (4 Seiten) in der Kategorie Beveiliging. Dieser Bedienungsanleitung war für 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/4
Buttons and controls
In the box
BE1560 Visit wrist receiver
BE1570 Charger
Elastic wrist band
Power supply
Power and battery
Mains power: 7.5 V DC/1500 mA
Power consumption
Receiver: Active: 100 mA, Idle: 3 mA
Charger: Active: 650 mA, Idle: 70 mA
Battery power
Receiver: 11.2 V V40H rechargeable
Charger: 41.2 V NiMH rechargeable
Operating and charging time
Receiver: ~30 h, Charging time: ~8 h
Charger: Battery charging time: ~24 h
Environment
For indoor use only
Operating temperature
15° to 35° C, 59° to 95° F
Relative humidity
15% to 90%, non-condensing
Frequency and coverage
Radio frequency
314.91 MHz, 433.92 MHz or 868.30
MHz, depending on the region
Coverage
50 – 250 m, 55 - 273 yd. depending
on the radio frequency and the
characteristics of the building
Accessories
BE1270 Bed shaker
BE9086 External trigger cable
Dimensions and weight
Receiver Charger
Height 49 mm 100 mm
Width 38 mm 95 mm
Depth 12 mm 117 mm
Weight 27 g 185 g
Visit LEDS
The Visit LEDs normally indicates
the following:
Orange LED, pacier symbol
The baby monitor is activated
Green LED, door symbol
The door transmitter is activated
Yellow LED, telephone symbol
The phone transmitter is activated
Red LED, re symbol
The smoke alarm is activated
Technical specications
Visit wrist receiver
Visit LEDs
Silicone wrist band 3.5 mm bed shaker input
Charger Charging LED
BE1270 bed shaker
Function button Mains LED
Bed shaker
test button
Battery LED
Power supply
BE8102
”click”
1 2 3
Getting started
1 Pull the battery tab on the charger and connect the power supply to the mains outlet. The mains LED lights up in green.
Place the wrist receiver in the charger and charge it for at least 2 hours. The charging LED is green during charging.
2 To test the radio link you need a Visit transmitter. Press the test button/s on the transmitter.
3 The receiver starts to vibrate and lights up a Visit LED. If a bed shaker is connected during charging, it will vibrate.
If nothing happens, see Troubleshooting.
Default signal pattern
When a transmitter is activated, the wrist receiver lights up an LED and starts to vibrate with a certain pace. This is called
signal pattern. The transmitters determine the pattern, and the default is as follows:
Activated transmitter Wrist receiver LED Wrist receiver / bed shaker vibration
Door transmitter Green Slow
Push button transmitter Green Slow
Telephone transmitter Yellow Medium
Baby monitor Orange Fast
Smoke alarm Red Long
Changing the signal pattern
The signal pattern can only be changed on the transmitters. See Changing the signal pattern for the relevant transmitter.
LED indications
When the wrist receiver battery is nearly depleted, the battery LED starts to blink in yellow. The charging time is up to 8 h.
The charger is equipped with a battery backup and the charger LEDs indicate the following:
LED Indication Status
Charging LED Green light The receiver battery is being charged.
Mains LED Green light The charger is powered by mains voltage.
Mains LED Green blinks The charger is powered by the battery backup.
Visit wrist receiver
Changing the radio key
If your Visit system is activated for no reason, there is probably a nearby system that triggers yours. In order to avoid radio
interference, you need to change the radio key on all units. The radio key switches are located on the transmitters.
Here is how you change the radio key:
1 Open the transmitter cover and move any radio key switch to the up (on position) to change
the radio key. See Changing the radio key for the relevant transmitter.
2 Press and hold the function button on the wrist receiver until the green and yellow Visit LEDs
blink alternately. Release the button.
3 Press the test button/s on the transmitter within 30 seconds to send the new radio key.
4 All Visit LEDs on the receiver blink 5 times to show that the radio key has been changed. It then returns to normal mode.
Note: All Visit units must be set to the same radio key in order to operate as a group.
1 2 3 4
5
Visit wrist receiver
Accessories
The wrist receiver can be complemented with the following accessory:
BE1270 Bed shaker
Wakes you with vibrations if anything happens while
you are asleep. Connect it to the charger and slide it
under your pillow or mattress.
Note: The bed shaker only works when the wrist receiver
is placed in the charger. The receiver will not vibrate
during charging, but the Visit LEDs will act as usual.
Press the bed shaker test button on top of the charger to
try the bed shaker vibration.
On
O
Warning! The wrist receiver and charger can ONLY USE RECHARGEABLE NiMH BATTERIES. Non-
rechargeable batteries will start to leak during charging and the battery acid will damage the electronics
in the wrist receiver and charger. The resulting damage is not covered by warranty.
BE1270
Produktspezifikationen
Marke: | Bellman |
Kategorie: | Beveiliging |
Modell: | Visit |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Bellman Visit benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Beveiliging Bellman
25 August 2024
24 August 2024
24 August 2024
24 August 2024
23 August 2024
23 August 2024
22 August 2024
22 August 2024
Bedienungsanleitung Beveiliging
- Beveiliging Medion
- Beveiliging Nedis
- Beveiliging Tevion
- Beveiliging Panasonic
- Beveiliging Bosch
- Beveiliging Siemens
- Beveiliging Powerfix
- Beveiliging Dymond
- Beveiliging Netgear
- Beveiliging Technaxx
- Beveiliging Alecto
- Beveiliging Gira
- Beveiliging Jacob Jensen
- Beveiliging MarQuant
- Beveiliging Topcraft
- Beveiliging Blaupunkt
- Beveiliging Grundig
- Beveiliging Trebs
- Beveiliging Alphatronics
- Beveiliging FlinQ
- Beveiliging Abus
- Beveiliging Elro
- Beveiliging EZVIZ
- Beveiliging Switel
- Beveiliging Steinel
- Beveiliging Lamax
- Beveiliging Perel
- Beveiliging Goobay
- Beveiliging Fenton
- Beveiliging Honeywell
- Beveiliging B/R/K
- Beveiliging First Alert
- Beveiliging BML
- Beveiliging Doro
- Beveiliging Hagenuk
- Beveiliging IGet
- Beveiliging Theben
- Beveiliging Xavax
- Beveiliging Monacor
- Beveiliging JUNG
- Beveiliging Ednet
- Beveiliging Aritech
- Beveiliging Humantechnik
- Beveiliging Eufy
- Beveiliging Skytronic
- Beveiliging Grothe
- Beveiliging Friedland
- Beveiliging DNT
- Beveiliging Plustek
- Beveiliging Grandstream
- Beveiliging BTicino
- Beveiliging EasyMaxx
- Beveiliging Eden
- Beveiliging Foscam
- Beveiliging Hikvision
- Beveiliging Heidemann
- Beveiliging Somfy
- Beveiliging Dahua
- Beveiliging Dedicated Micros
- Beveiliging Dericam
- Beveiliging Directed Electronics
- Beveiliging Electronics Line
- Beveiliging Entrya
- Beveiliging Epine
- Beveiliging Fracarro
- Beveiliging Galaxy
- Beveiliging GE Security
- Beveiliging Golmar
- Beveiliging Guardall
- Beveiliging Home8
- Beveiliging HomeWizard
- Beveiliging I-Tel
- Beveiliging Inner Range
- Beveiliging Jablotron
- Beveiliging Jupiter Pro
- Beveiliging Kompernass
- Beveiliging Ksenia
- Beveiliging ME
- Beveiliging Mr Safe
- Beveiliging Myfox
- Beveiliging NetworX
- Beveiliging Niko
- Beveiliging Nor-tec
- Beveiliging Notifier
- Beveiliging Oplink
- Beveiliging Paradox
- Beveiliging PIR Alarm
- Beveiliging Protector
- Beveiliging RISCO Group
- Beveiliging Satel
- Beveiliging SecuFirst
- Beveiliging Secure Pro
- Beveiliging Smartalarm
- Beveiliging SmartHome
- Beveiliging Sonic Alert
- Beveiliging Stobo
- Beveiliging Storage Options
- Beveiliging Visonic
- Beveiliging Wanscam
- Beveiliging Woonveilig
- Beveiliging Xena
- Beveiliging Zmodo
- Beveiliging Axis
- Beveiliging Ajax
- Beveiliging AngelEye
- Beveiliging AceSee
- Beveiliging Alhua - Dahua
- Beveiliging Bitron Video
- Beveiliging AVTech - Velleman
- Beveiliging Bolyguard
Neueste Bedienungsanleitung für -Kategorien-
17 September 2024
17 September 2024
16 September 2024
16 September 2024
26 August 2024
26 August 2024
26 August 2024
26 August 2024
26 August 2024
26 August 2024