BeamZ BUV45TL Bedienungsanleitung

BeamZ Beleuchtung BUV45TL

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für BeamZ BUV45TL (12 Seiten) in der Kategorie Beleuchtung. Dieser Bedienungsanleitung war für 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/12
UV-set 45cm or 60cm Holder and Tube
Ref. nr.: 160.413 / 160.414
INSTRUCTION MANUAL
GEBRUIKSAANWIJZING
GEBRAUCHSANLEITUNG
MANUAL DE INSTRUCCIONES
MANUEL D'INSTRUCTIONS
V2.0
2
ENGLISH
Congratulations to the purchase of this Beamz light eect. Please read this manual thoroughly prior to using the unit in order to
benet fully from all features.
Read the manual prior to using the unit. Follow the instructions in order not to invalidate the warranty. Take all precautions to
avoid re and/or electrical shock. Repairs must only be carried out by a qualied technician in order to avoid electrical shock.
Keep the manual for future reference.
- Prior to using the unit, please ask advice from a
specialist. When the unit is switched on for the rst time,
some smell may occur. This is normal and will disappear
after a while.
- The unit contains voltage carrying parts. Therefore do
NOT open the housing.
- Do not place metal objects or pour liquids into the unit
This may cause electrical shock and malfunction.
- Do not place the unit near heat sources such as
radiators, etc. Do not place the unit on a vibrating
surface. Do not cover the ventilation holes.
- The unit is not suitable for continuous use.
- Be careful with the mains lead and do not damage it. A
faulty or damaged mains lead can cause electrical shock
and malfunction.
- When unplugging the unit from a mains outlet, always
pull the plug, never the lead.
- Do not plug or unplug the unit with wet hands.
- If the plug and/or the mains lead are damaged, they
need to be replaced by a qualied technician.
- If the unit is damaged to such an extent that internal
parts are visible, do NOT plug the unit into a mains outlet
and DO NOT switch the unit on. Contact your dealer. Do
NOT connect the unit to a rheostat or dimmer.
- avoid re and shock hazard, do not expose the unit to To
rain and moisture.
- All repairs should be carried out by a qualied technician
only.
- Connect the unit to an earthed mains outlet (220-
240Vac/50Hz) protected by a 10-16A fuse.
- During a thunderstorm or if the unit will not be used for a
longer period of time, unplug it from the mains. The rule
is: Unplug it from the mains when not in use.
- If the unit has not been used for a longer period of time,
condensation may occur. Let the unit reach room
temperature before you switch it on. Never use the unit in
humid rooms or outdoors.
- During operation, the housing becomes very hot. Do not
touch it during operation and immediately after.
- To prevent accidents in companies, you must follow the
applicable guide lines and follow the instructions.
- Secure the unit with an extra safety chain if the unit is
ceiling mount. Use a truss system with clamps. Make
sure nobody stands in the mounting area. Mount the
eect at least 50cm away from inammable material and
leave at least 1 meter space on every side to ensure
sucient cooling.
- This unit contains high intensity LEDs. Do not look into
the LED light to prevent damage to your eyes.
- Do not repeatedly switch the xture on and o. This
shortens the life time.
- Keep the unit out of the reach of children. Do not leave
the unit unattended.
- Do not use cleaning sprays to clean switches. The
residues of these sprays cause deposits of dust and
grease. In case of malfunction, always seek advice from
a specialist.
- Only operate the unit with clean hands.
- Do not force the controls.
- If the unit has fallen, always have it checked by a
qualied technician before you switch the unit on again.
- Do not use chemicals to clean the unit. They damage the
varnish. Only clean the unit with a dry cloth.
- Keep away from electronic equipment that may cause
interference.
- Only use original spares for repairs, otherwise serious
damage and/or dangerous radiation may occur.
- Switch the unit o prior to unplugging it from the mains
and/or other equipment. Unplug all leads and cables
prior to moving the unit.
- Make sure that the mains lead cannot be damaged when
people walk on it. Check the mains lead before every use
for damages and faults!
- The mains voltage is 220-240Vac/50Hz. Check if power
outlet match. If you travel, make sure that the mains
voltage of the country is suitable for this unit.
- Keep the original packing material so that you can
transport the unit in safe conditions
This mark attracts the attention of the user to high voltages that are present inside the housing and that are of sucient
magnitude to cause a shock hazard.
This mark attracts the attention of the user to important instructions that are contained in the manual and that he should
read and adhere to.
DO NOT LOOK DIRECTLY INTO THE LENS. This can damage your eyes. Persons who are subject to epileptic attacks
should be aware of the eects that this light eect may have on them.
The unit has been certied CE. It is prohibited to make any changes to the unit. They would invalidate the CE certicate and
their guarantee!
NOTE: To make sure that the unit will function normally, it must be used in rooms with a temperature between 5°C/ °F 41 and
35 95°C/ °F.
Electric products must not be put into household waste. Please bring them to a recycling centre. Ask your local authorities or your
dealer about the way to proceed. The specications are typical. The actual values can slightly change from one unit to the other.
Specications can be changed without prior notice.
3
POWERSUPPLY
On the label on the backside of the light eect is indicated on this type of power supply must be connected. Check that the
mains voltage corresponds to this, all other voltages than specied, the light eect can be irreparably damaged. The light eect
must also be directly connected to the mains and may be used. No dimmer or adjustable power supply.
INSTALLATION
Attention:
• The installation of the xture has to be built and constructed in a way that it can hold 10 times the weight for 1 hour
without any harming deformation.
• The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net. This
secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main
attachment fails.
• Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing.
• The operator has to make sure that safety-relating and machine-technical installations are approved by an expert
before taking into operation for the rst time and after changes before taking into operation another time.
• The operator has to make sure that safety-relating and machine-technical installations are approved by a skilled
person once a year.
• The xture should be installed in the position where persons cannot reach and where persons may walk by or be
seated.
INSTALLING / REPLACING THE LAMP
Before replacing the lamp, unplug the power lead and let the lamp cool down (approx. 5 minutes).
During the installation do not touch the glass-bulbs bare-handed! Do not install lamps with a higher wattage! Lamps with a
higher wattage generate temperatures the device was not designed for.
During the operation, the lamp reaches temperatures up to 80° C.
FIXTURE CLEANING
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output.
Cleaning frequency depends on the environment in which the xture operates: damp, smoky or particularly dirty surrounding
can cause greater accumulation of dirt on the unit’s optics.
• Make sure the area below the installation place is free from unwanted persons during servicing
• Housings, xations and installations spots( ceiling, truss, suspensions) should be totally free from any deformation
• The mains cables must be in impeccable condition and should be replaced immediately when even a small problem is
detected
• The interior of the xture should be cleaned annually using a vacuum cleaner or air-jet.
• Clean with soft cloth using normal glass cleaning uid.
• Always dry the parts carefully.
• Clean the external optics at least every month. Clean the internal optics at least every 30/60 days.
ATTENTION: We strongly recommend internal cleaning to be carried out by qualied worker!
CAUTION: Please consider the respective national norms during the
installation! The installation must only be carried out by an
authorized employee or dealers!
CAUTION: When installing the device, make sure there is no highly in
inammable material (decoration articles, etc.) in between a
distance of min 0.5 meter.

Produktspezifikationen

Marke: BeamZ
Kategorie: Beleuchtung
Modell: BUV45TL

Brauchst du Hilfe?

Wenn Sie Hilfe mit BeamZ BUV45TL benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Beleuchtung BeamZ

BeamZ

BeamZ BUV45TL Bedienungsanleitung

21 Juni 2024
BeamZ

BeamZ BUV15TL Bedienungsanleitung

21 Juni 2024
BeamZ

BeamZ Fuze 75 Beam Bedienungsanleitung

5 Juni 2024
BeamZ

BeamZ Ignite 220 Bedienungsanleitung

5 Juni 2024
BeamZ

BeamZ BWA550Z Bedienungsanleitung

5 Juni 2024
BeamZ

BeamZ BBP44 Bedienungsanleitung

28 Mai 2024
BeamZ

BeamZ BBP62 Bedienungsanleitung

23 Mai 2024
BeamZ

BeamZ BUV63 Bedienungsanleitung

16 April 2024
BeamZ

BeamZ Cobra 100H Bedienungsanleitung

1 April 2024
BeamZ

BeamZ DMX384 Bedienungsanleitung

28 März 2024

Bedienungsanleitung Beleuchtung

Neueste Bedienungsanleitung fĂźr -Kategorien-

Stairville

Stairville BEL4 Battery Event Light 4x15W Bedienungsanleitung

21 August 2024
Maul

Maul Avior Bedienungsanleitung

15 August 2024
Black Diamond

Black Diamond Spot R 400 Bedienungsanleitung

28 Juni 2024
Black Diamond

Black Diamond Storm 450 Bedienungsanleitung

28 Juni 2024
Black Diamond

Black Diamond Storm R 500 Bedienungsanleitung

28 Juni 2024
Black Diamond

Black Diamond Cosmo R 350 Bedienungsanleitung

28 Juni 2024
Black Diamond

Black Diamond Astro R 300 Bedienungsanleitung

28 Juni 2024
Black Diamond

Black Diamond Icon 700 Bedienungsanleitung

28 Juni 2024
Black Diamond

Black Diamond Spot 400 Bedienungsanleitung

28 Juni 2024
Louis Poulsen

Louis Poulsen Panthella 160 Bedienungsanleitung

27 Juni 2024