Babysense Connect Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Babysense Connect (11 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/11
User Manual
Babysense Connect
Non-Contact Movement Monitor
Do not handle roughly, drop or throw.
Follow the installation instruction carefully to ensure the device is installed securely and correctly.
Babysense is not a toy. Do not allow children of any age to play with it.
Do not put any additional baby or pet in the bed.
Babysense Connect is intended for use with one infant and cannot be used for two infants in one bed.
Babysense Connect cannot be used with co-sleepers that are attached to the parent's/caregiver's bed.
Do not operate the unit in the presence of electromagnetic interference.
Portable and mobile RF communications equipment may e ect operation of this device.
You must undertake the performance test daily and every time you move the monitor, change bedding
or relocate crib/bed position (Daily Performance Test Section).
Do not operate vaporizer or ventilator directly towards the bed.
To avoid possible danger from sensor cords, ensure that excess cords are pulled back under the
mattress, secured with the included cable tie and are not visible or reachable.
Install 4 new and identical Alkaline size AA 1.5 volt batteries.
NOTE: Rechargable batteries may be used -
www.babysensemonitors.com/pages/bs-connect-batteries
for
applicable list. The batteries must be fully charged before inserting in the Babysense Control Unit
Please remove batteries if the device is not in use for an extended time (2 weeks or more).
When using the device after having not used it for an extended period of time please install 4 new
identical Alkaline AA Batteries or fully charge and insert the rechargable batteries
(
www.babysensemonitors.com/pages/bs-connect-batteries
for applicable list. . )
If you have any problems with this device, such as setting up, maintaining or using, please
contact the manufacturer’s service personnel. Also, please report to the manufacturer if any unexpected
operation or events occur.
Do not use the equipment if you notice a change in the system's performance, if the system is
damaged, or if any of its components are worn or frayed.
The equipment should not be used adjacent to or stacked with other equipment. If adjacent or stacked
use is necessary, the equipment should be observed to verify normal operation in the conguration in
which it is used.
Ensure you read this user manual before installing and using the product.
Babysense is a high quality, high sensitivity electronic device, which must be handled with care:
Warnings
Babysense Connect
Non-Contact Movement Monitor
SAFETY INSTRUCTIONS FOR HUB AC POWER ADAPTER
The adapter should not be exposed to direct heat sources such as a candle, stove, radiator, heat
register or other appliance that emits heat.
During continual use, the power adapters may become warm to the touch.
Examine intactness of the power cord and its plug.
The adapter must be handled with care: Do not handle roughly, drop or throw.
Once removing the power adapter from the wall outlet, hold and pull from the receptacle. Do not pull
on the cable itself or bend the cable as that will put additional stress on the cable and could lead to
damages.
Do not touch the power adapter with wet hands or allow liquids to spill on it.
Make sure the mains adaptor cables are kept out of reach of your baby and other young children at all
times. To avoid possible danger from power cords, the cords should be secured and never be hung
on or near the crib.
Do not replace the plugs or cable on your power adapter. This product should only be used with the AC
power adapters supplied by the manufacturer, as included in this package.
Never cut, damage or bend the power cord.
Do not put any objects on top of the power cord, which could cause overheating, damage,
inflammation and electrocution.
Do not leave the power adapter connected to the wall outlet when it is not plugged into the Hub.
•
•
•
•
•
•
•
•
•
•
•
Babysense continually detects baby's movements and will set off a sound and visual alarm if movement
stops within 20 seconds or if the monitor detects less than 10 micro-movements per minute. The system's
non-touch, under the mattress sensor pads monitor baby's movement without restraining him.
Principle of Operation
Babysense monitors and alerts, but cannot prevent any type of distress. The responsibility for applying rst
aid rests on caretakers. The Babysense senses movements and motion only, and cannot monitor other
occurrences. The purpose of the device is to alert when stopping or slowing of movement occurs.
Babysense is a unique safety and reassurance system which helps give parents peace of mind, alerting if
movements stop or become irregularly slow, giving time to intervene. There are a number of cautionary
steps, which are internationally applicablefor SAFE SLEEPING:
Babysense Connect is a home movement monitor for infants up to one year of age, and is not to be used
with high-risk infants requiring constant medical supervision.
Medically trained staff such as nurses, or non-medically trained users such as parents or caregivers may
use the Babysense Connect. Babysense Connect is intended for home use.
Always lay baby to sleep on his or her back.
Refrain from smoking near or around baby.
Avoid over-heating of baby's surrounding.
Do not leave any objects near your baby that can cause su ocation.
It is strongly advised that parents and caregivers learn how to give rst aid to babies.
*
*
*
*
*
Please note
Installation
To insert the batteries, remove the battery cover by placing a flat screwdriver in the opening recess and
gently pulling away from the control unit (see illustration 7). Insert, , in accordance with the markings
the 4 supplied Alkaline size AA 1.5 volt batteries or the rechargable batteries
(
www.babysensemonitors.com/pages/bs-connect-batteries
for applicable list. and close cover.)
Note: Please dispose of used batteries in accordance with local waste regulations.
Note: Once batteries are inserted the Blue LED will flash 3 times indicating that is activated.
1.
Place control unit holder on the base of the crib or bed and in between two bars as shown in illustration 1.
2.
applicableapplicable


Produktspezifikationen

Marke: Babysense
Kategorie: Nicht kategorisiert
Modell: Connect

Brauchst du Hilfe?

Wenn Sie Hilfe mit Babysense Connect benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Babysense

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂźr -Kategorien-