Aube TH132 A Bedienungsanleitung

Aube Thermostaat TH132 A

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Aube TH132 A (3 Seiten) in der Kategorie Thermostaat. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/3
n
o
p
q
r
s
t
u/
v
w


Control Module
TH132 A/F/AF
Owner’s Guide
TH132 Description
Models Overview
Configure the Switches
n
o


n
o
n
n
o

Install the Control Module
First Power ON
Set the Time and Day
Adjust the Temperature Setpoints
Select the Operating Mode
n
o
p
q
r
s
n
o
p
n
o
p
q
r
s
n
o
p
q
r
s
t
u
v
Program Your Schedule
Temperature Control Technical Specifications




Warranty
PB130 400-130-001-E 19/9/05 1/1
nOne (1) PB130-230 power base
oOne (1) floor sensor (for AF and F control modules only)
pOne (1) wall plate (optional, in certain countries)
Turn off power to the heating system at the main power panel to avoid
electrical shock. Installation should be carried out by an electrician.
 All work must conform to the applicable country standards for
electrical installations and wiring.
 This thermostat should be connected on a circuit equipped with
a fuse or a circuit breaker. It must be installed on a certified
electrical box.
 For a new installation, choose a location about 1.5 m above the
floor.
 For electric baseboards, convectors and fan-forced heaters, the
thermostat must be installed facing the heating system.
 The thermostat must be installed on an inside wall.
 Avoid locations where there are air drafts (top of staircase, air
outlet), dead air spots (behind a door), direct sunlight or
concealed chimneys or stove pipes.
Model: PB130A-230
Supply: 230 VAC, 50 Hz
Load: 15 A maximum (resistive only)
Power: 3450 Watts (NI) @ 230 VAC
Conformity: EN60730-2-9 / EN50081-1 / EN50082-2
Storage: -20°C to 50°C
Protection: Class 2
Protection degree: IP21
Automatic action: Type 1.B
Environment: Normally polluted
Size (H • W • D) : 2.95 x 2.95 x 0.55 in. (75 x 75 x 14 mm)
NOTE: The terminals are designed to handle a cross-section of wire
measuring 0.33 to 3.1 mm2.
nRemove the screw holding the
control module to the power base
and lift the lower part upwards.
The screw cannot be completely
removed.
pConnect the wires:
• :Power
Terminals 1 & 5
• Load:
Terminals 2 & 4
see note 1
• Pilot Wire:
Terminal 3
see note 2
• :Floor sensor
Terminals 6 & 7
(no polarity)
see note 3
Note 1 If a contactor is used between the thermostat and the load,
install a snubber at the contactor’s coil terminal to ensure
the proper operation of the thermostat.
Note 2 This connection is required on some models only.
Note 3 For the proper operation of the thermostat, the floor sensor
must be centered between two heater wires having a
maximum temperature of 80°C. The floor sensor wire must
not cross any heater wire or be placed close to it.
rPush wires into the electrical box and
secure the base to the electrical box
anchorage. The head of the screw
must be less than 2 mm thick.
sBEFORE installing the control
module onto the base, set the
configuration switches (if any)
on the control module (refer to
the user guide).
WARNING: This power base must be used only with 15-minute
heating cycles. If your control module has a selector switch for
choosing the heating cycle, ensure that the switch is correctly set.
tReturn power to the heating system.
n
n
n
nn
o
o
o
oo 2.
p
p
p
pp 3.
q
q
q
qq 4.

Produktspezifikationen

Marke: Aube
Kategorie: Thermostaat
Modell: TH132 A

Brauchst du Hilfe?

Wenn Sie Hilfe mit Aube TH132 A benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Thermostaat Aube

Bedienungsanleitung Thermostaat

Neueste Bedienungsanleitung für -Kategorien-