Atlona AT-OME-EX-RX Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Atlona AT-OME-EX-RX (12 Seiten) in der Kategorie Audio/Video-Konverter. Dieser Bedienungsanleitung war fĂĽr 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/12
1
Installation Guide
AT-OME-EX-RX
Omega™ 4K/UHD
HDMI Over HDBaseT Receiver with USB, Control, and PoE
AT-OME-EX-RX
The Atlona AT-OME-EX-RX is an HDBaseT receiver for video up to 4K/60 4:2:0, plus embedded
audio, control, Ethernet, and USB over distances up to 330 feet (100 meters). Part of the
Omega™ Series of integration products for modern AV communications and collaboration,
the OME-EX-RX is HDCP 2.2 compliant and receives IR, RS-232, and IP control signals. With
a matching HDBaseT transmitter, the integrated USB extension is ideal for software video
conferencing and the use of touch or interactive displays. The OME-EX-RX includes two USB
interfaces for devices such as a camera or display. This receiver is ideal for use with Omega
Series transmitters as well as switchers with HDBaseT outputs. Also available is the OME-EX-
KIT which includes the OME-EX-TX and OME-EX-RX.*
* The AT-OME-EX-RX is not compatible with the AT-UHD-HDVS-300 system for extending USB.
IMPORTANT: Visit http://www.atlona.com/product/AT-OME-EX-RX for the
latest îś±rmware updates and User Manual.
1 x AT-OME-EX-RX
1 x Captive screw connectors, 4-pin
2 x Mounting plates
4 x Mounting screws
1 x 48 V DC power supply
1 x Installation Guide
Package Contents
2
Installation Guide
AT-OME-EX-RX
1 LAN
Connect a category cable from this port to the display (sink) device. This cable provides IP
pass-through transport control to the display (sink) device, from a control system connected
to the transmitter.
2 DEVICE
Connect up to two USB 2.0 devices (e.g. mouse, keyboard, etc.) to these ports.
These ports provide 2.5 W per USB device.
3 FW
Connect a mini USB-to-USB cable from this port, to a computer, to update the îś±rmware.
Refer to for more information.
Updating the Firmware (page 10)
4 PWR / LINK
The LED indicator will glow green when the AT-OME-EX-RX is powered. The PWR LINK
LED indicator glows yellow when a solid link is established between the transmitter and the
AT-OME-EX-RX. Refer to for more information.
LED Indicators (page 5)
5 DC 48V
Connect the included 48 V DC power supply to this power receptacle.
6 RS-232 / IR
Connect the included 4-pin captive screw block to this receptacle. Refer to RS-232 and IR
(page 3) for more information.
7 HDBaseT IN
Connect a category cable from this port to the port of the AT-OME-EX-TX or HDBaseT OUT
other PoE-compatible transmitter.
8 HDMI OUT
Connect an HDMI cable from this port to the display (sink) device.
LAN FW
OMEGAT M
DEVICE
PWR
LINK
HDMI OUTHDBaseT IN
RX TXTX
RS-232 IR
AT-OME-EX-RX
DC 48V
Front
Rear
8
65 7
2
1 3 4
3
Installation Guide
AT-OME-EX-RX
The AT-OME-EX-RX provides pass-through transport of RS-232 protocol and/or IR over
HDBaseT, which allows communication between a control system and an RS-232 or IR device.
This step is optional.
1. Use wire strippers to remove a portion of the cable jacket.
2. Remove at least 3/16” (5 mm) from the insulation of the RX, TX, and GND wires for the
RS-232 connection.
3. Insert the TX, RX, and GND wires into correct terminal using one of the included 4-pin
captive screw connectors.
4. Repeat step 2 for the S and GND wires for the IR connection.
5. Insert the S (signal) wire in to the TX terminal and the ground wire to the GND terminal.
6. Tighten the captive screws to secure the wires in place. Do not over-tighten or use
high-torque devices to prevent damage to the connector block.
NOTE: Typical DB9 connectors use pin 2 for TX, pin 3 for RX, and pin 5 for
ground. On some devices functions of pins 2 and 3 are reversed. Note that the
signal (S) pin for the IR is labeled as “TX” on the port.
GND
to control system
or AT-VCC-IR-KIT
DE-9 (RS-232) port
RX
TX
S
GND
RS-232 and IR
Power
1. Locate the included orange captive-screw block, and loosen the screws to allow room to
insert the copper wiring.
2. Wire the included power supply to the block, as shown below. Do not use high-torque
devices, when securing the wires to the captive-screw terminal block, as this may damage
the screws and/or block.
Black
White
48 V DC
power supply


Produktspezifikationen

Marke: Atlona
Kategorie: Audio/Video-Konverter
Modell: AT-OME-EX-RX

Brauchst du Hilfe?

Wenn Sie Hilfe mit Atlona AT-OME-EX-RX benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Audio/Video-Konverter Atlona

Bedienungsanleitung Audio/Video-Konverter

Neueste Bedienungsanleitung fĂĽr -Kategorien-