ATen PE0210SA Bedienungsanleitung

ATen Anbaustein PE0210SA

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für ATen PE0210SA (2 Seiten) in der Kategorie Anbaustein. Dieser Bedienungsanleitung war für 19 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

CRack Mounting

other trademarks are the property of their respective owners.

This product is RoHS compliant.

Printing Date: 03/2019

Basic 1U PDU with surge protection

Quick Start Guide

PE0107S/PE0110S/PE0207S/

PE0209S/PE0210S

PE0107S/PE0110S/PE0207S/PE0209S/PE0210S with surge protection Quick Start Guide www.aten.com

ATEN NRGence™

AHardware Review

1 2 3 46 6 7

Rack Mounting

The Basic PDU can be installed in a 1U conﬁ guration on the side of a rack.

To rack mount the device, stabilize the device on the rack and tighten

screws onto the rack mount ears.

Hardware Review

1 Power Inlet

2 Circuit Breaker

3 Surge Protection

4 Surge Protection Indicator

5 Power Outlets

6 Rack Mount Ears

7 Grounding

Support and Documentation Notice

All information, documentation, ﬁ rmware,

software utilities, and speciﬁ cations

contained in this package are subject to

change without prior notiﬁ cation by

the manufacturer.

To reduce the environmental impact of our

products, ATEN documentation and software

can be found online at

http://www.aten.com/download/

Technical Support

www.aten.com/support

이 기기는 업무용(A급) 전자파적합기기로서 판매자 또는

사용자는 이 점을 주의하시기 바라며, 가정외의 지역에

서 사용하는 것을 목적으로 합니다.

Scan for

more information

EMC Information

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE

STATEMENT:

This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area

is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

FCC Caution: Any changes or modiﬁ cations not expressly approved by

the party responsible for compliance could void the user's authority to

operate this equipment.

Warning: Operation of this equipment in a residential environment

could cause radio interference.

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Package Contents

1 Power Distribution Unit

1 Power Cord

1 User Instructions

pe0110sa is the example used here. Please conﬁ rm the models corresponding to the given

pictures (models and pictures are not directly related).

BHardware Installation

Note: For safety reasons the equipment should be installed near the wall socket outlet and

the disconnected device (appliance coupler on detachable power supply cord or plug

on non-detachable power supply cord) should be readily accessible

Basic PDU

Rack

Hardware Installation

Refer to the installation diagram (the numbers in the diagram correspond to

the numbered steps), and do the following:

1Connect the Basic PDU's power cord to an AC power source.

2For each device you want to connect, connect its power cable between

the device's AC socket (where applicable) and any available outlet on the

Basic PDU.

Note: We strongly advise that you do not plug the Basic PDU into a multi

socket extension cord, since it may not receive enough amperage to

operate correctly. Once you have ﬁ nished

Surge Protection Indicator

The Surge Protection Indicator is as shown in the Hardware Review.

It should normally be lit when the unit is powered.

If the indicator is not lit when the unit is powered, please power down the

unit and any connected device safely. Return the unit to the dealer closest to

your location for further assistance.

Produktspezifikationen

Marke:	ATen
Kategorie:	Anbaustein
Modell:	PE0210SA
Breite:	482 mm
Tiefe:	44.4 mm
Gewicht:	670 g
Produktfarbe:	Schwarz
Höhe:	45 mm
Energieschutzeigenschaften:	Überstrom
AC Eingangsfrequenz:	50 - 60 Hz
Betriebstemperatur:	0 - 40 °C
Gehäusematerial:	Aluminium
Temperaturbereich bei Lagerung:	-20 - 60 °C
Höhe bei Betrieb:	0 - 3000 m
Anzahl der AC-Ausgänge:	10 AC-Ausgänge
AC-Steckertypen:	NEMA 5-20R
Stromstärke (maximal):	20 A
Druckanstiegsschutz:	Ja
Nominale Eingang Spannung:	100 - 120 V
Rack-Kapazität:	1U
PDU-Typen:	Standard
Ladekapazität:	2400 VA