ATen BP36V18AH Bedienungsanleitung

ATen Nicht kategorisiert BP36V18AH

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für ATen BP36V18AH (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 33 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

1 Important Safety Instructions

Please comply with all warnings and operating instructions in this manual strictly. Read

the following instructions carefully before installing the unit. Do not operate this unit

before reading through all safety information and operating instructions carefully.

• Do not try to repair the unit yourself, contact your local supplier or your warranty

will be void.

• To eliminate any overheating of the battery box, keep all ventilation openings free

from obstruction and do not place any foreign objects on top of the battery bank.

Keep the battery box 20cm away from the wall.

• Make sure the battery box is installed within the proper environment as specified.

(0-40°C and 30-90% non-condensing humidity)

• Do not install the battery box under direct sunlight. Your warranty will be void if the

batteries fail due to overheating.

• This battery box is not designed for use in dusty, corrosive and salty environment.

• The warranty for this battery bank will be void if water or other liquid is spilt or

poured directly onto the battery box. Similarly we do not warrant any damage to

the battery box if foreign objects are deliberately or accidentally inserted into the

battery box enclosure.

• The battery will discharge naturally if the system is unused for a period of time.

• It should be recharged every 2-3 months if unused. If this is not done, then the

warranty will be null and void. During normal operation, the batteries will be

automatically remained in charged condition.

• Servicing of batteries should be performed or supervised by trained personnel with

knowledge of batteries and the required precautions.

• When replacing batteries, it is necessary to replace ALL batteries with the same

quantity, type & capacity.

• CAUTION – Do not dispose of battery or batteries in a fire. The battery may

explode.

• CAUTION – Do not open or mutilate the batteries. The electrolyte from the

batteries is toxic and harmful to the skin and eyes.

• CAUTION – Risk of Electric Shock –Hazardous voltage may exist between battery

terminals and ground. Test before touching with bare hands.

• CAUTION – A battery can present a risk of electrical shock and high short circuit

current. The following precaution should be observed when working on

batteries:

1. Remove watches, rings, or other metal objects.

2. Use tools with insulated handles.

3. Wear rubber gloves and boots.

4. Do not lay tools or metal parts on top of batteries.

5. Disconnect charging source prior to connecting or disconnecting battery

terminals.

• Do not plug or unplug the battery connector if UPS works in DC (discharging)

mode.

2 Product Overview and Setup

NOTE: Before installation, please inspect the unit. Be sure that nothing inside the

package is damaged. Please keep the original package in a safe place for future

use.

2.1 Rear Panel View



DC connector: connects to either UPS or a 2

battery box



DC breaker: Battery over-current protection breaker

2.2 Installation and Setup with UPS

Unpacking and Inspection

1. Remove the battery box from the packing.

Note: The battery box is very heavy, be cautious when unpacking and lifting

the unit to avoid injury.

2. Check the inside package

 Battery box unit

 Quick guide

 Battery connection cable x 1

 Ear x 2 & screw x 8

 Extended stand

Battery Box User Manual

Battery connection cable

Ears Screws

Extended stand

Selecting Installation Position

It is necessary to select a proper environment to install the unit in order to

minimize the possibility of damage to the battery box and extend the life of the

batteries. Please follow the instructions below:

1. Keep at least 20cm (8 inches) clearance from the rear panel of the unit from the

wall or other obstructions.

2. Do not block the air-flow to the ventilation openings of the unit.

3. Please ensure the installation site environmental conditions are in accordance

with the unit’s working specifications to avoid overheat and excessive moisture.

4. Do not place the unit in a dusty or corrosive environment or near any

flammable objects.

5. This unit is not designed for outdoor use.

2.3 Mounting

This unit can either be rack mounted or placed vertically on the desk.

Rack Mount

Vertical (Tower) Desktop Mount

2.4 Connecting to UPS or Another Battery Box

Follow the diagrammatic instructions below to connect your battery box to a UPS

or another battery box:

2.5 Available Battery Specs

This battery box has been designed to operate with the following batteries:

24V18AH: 4 pieces of 12V 9Ah batteries

36V18AH: 6 pieces of 12V 9Ah batteries

48V18AH: 8 pieces of 12V 9Ah batteries

72V18AH: 12 pieces of 12V 9Ah batteries

3 Storage & Maintenance

The unit contains no user-serviceable parts. If the battery service life (3~5 years at

25°C ambient temperature) has been exceeded, the batteries must be replaced. In

this case, please contact your dealer.

Storage

Before storing, charge the unit for 4 hours. Store the unit covered and upright in a

cool, dry location. During storage, follow the instructions shown in the table:

Storage Temperature Recharge Frequency Charging Duration

-25°C - 40°C Every 3 months 1-2 hours

40°C - 45°C Every 2 months 1-2 hours

Be sure to deliver the spent battery to a recycling facility or ship it

to your dealer in the replacement battery packing material.

Produktspezifikationen

Marke:	ATen
Kategorie:	Nicht kategorisiert
Modell:	BP36V18AH
Breite:	438 mm
Tiefe:	88 mm
Gewicht:	21500 g
Produktfarbe:	Schwarz
Höhe:	380 mm
Betriebstemperatur:	0 - 40 °C
Relative Luftfeuchtigkeit in Betrieb:	0 - 90 %
Zertifizierung:	cTUVus, RoHS
Temperaturbereich bei Lagerung:	-15 - 45 °C
Anzahl unterstützter Akkus/Batterien:	6
Ausgangsstrom:	50 A
Ausgangsspannung:	36 V
Eingangsspannung:	36 V