Atdec VFS-DV Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Atdec VFS-DV (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 40 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
T
T
T
TTop of
op of
op of
op of
op of
Display
Display
Display
Display
Display
There are two mounting hole configurations:
There are two mounting hole configurations:
There are two mounting hole configurations:
There are two mounting hole configurations:
There are two mounting hole configurations:
• 75 x 75mm
• 75 x 75mm
• 75 x 75mm
• 75 x 75mm
• 75 x 75mm
• 100 x 100mm
• 100 x 100mm
• 100 x 100mm
• 100 x 100mm
• 100 x 100mm
from the Hardware supplied to suit
from the Hardware supplied to suit
from the Hardware supplied to suit
from the Hardware supplied to suit
from the Hardware supplied to suit
your Displa
your Displa
your Displa
your Displa
your Display
y
y
yy.
.
.
.
.
Mounting Screws (x4)
Mounting Screws (x4)
Mounting Screws (x4)
Mounting Screws (x4)
Mounting Screws (x4)
VESA Plate
VESA Plate
VESA Plate
VESA Plate
VESA Plate
Component Checklist
VFS-DV
IMPORTANT INFORMATION:
Step 1. Check Components
Step 2. Attach Upright Pole to Base
! IMPORTANT - Install Visidec Freestanding/Double Vertical as per Installation Instructions.
!
Each Quickshift Donut supports a maximum weight of 12kg (26.5lbs)
! This product supports VESA mounting hole configurations: 75x75mm and 100x100mm.
! The manufacturer accepts no responsibility for incorrect installation.
Display Mounting
Screws
Hardware
Check you have received all parts against the component checklist and Hardware above.
M4x12mm (x8)
VESA Plate (x2)
M4x10mm (x8)
M4x16mm (x8)
Security Screw (x2)
Cable Ball (x4) Cable Clip (x3)
5/3mm Allen Key
(x1 each)
Installation Instructions
Freestanding Double Vertical l
Base
Upright Pole
TOOLS REQUIRED:
Phillips Head Screw Driver
M8x50mm
Screw (x1)
Step 3. Attach Quickshift Donuts to the Visidec Pole
(Ensure the cable slot faces towards the rear)
TIGHTEN
If the Quickshift Donut requires further
tightening use the supplied 5mm Allen key.
(Visidec 42mm pole shown)
Slot
Groove
Insert
Close the lever to lock the Quickshift
Donut in place.
Slide the Quickshift Donut onto the Pole.
CLOSE
Cable Slot
USER
BACK
TIGHTEN
FIRMLY
Upright Pole
M8x50mm Screw
5mm Allen Key
Attach the Upright Pole to the Base as shown
below. Ensure the Cable Slot faces towards the rear.
Quickshift
Donuts (x2)
Step 4. Attach the VESA Plate to your Display
100mm
100mm
100mm
100mm
100mm
75mm
75mm
75mm
75mm
75mm
75mm
75mm
75mm
75mm
75mm
100mm
100mm
100mm
100mm
100mm
Back of Display
Back of Display
Back of Display
Back of Display
Back of Display
LOOSEN
(Repeat steps 4 to 7 for each Display)
(Optional)
TIGHTEN (+kg)
Cable
Balls (x2)
Cable
Clips (x2)
LOOSEN (-kg)
Installation Complete
C
No portion of this document or any artwork contained herein should be reproduced in anyway without the express written consent Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 12.10.11
Step 5. Attach your Display to the Quickshift Donut
HOOK
Back of Display
Quickshift Mount.
Hook the top of the VESA plate onto the
Press and hold the Release Buttons. Gently
push bottom of VESA Plate into Quickshift
Mount. Release Buttons to lock in place.
Release Button Phillips-head
Screwdriver
Security Screw
CLOSE
OPEN
Slide the Quickshift Donut to
desired position.
Connect cables to your Displays, routing
them down to the rear of the poles.
Push the cables into the slots, using either
the Cable Balls or Cable Clips to secure
them to the pole as shown.
Note: Ensure enough slack is left in cables
to allow for movement. When the slot in
each pole cannot be used, use the supplied
Cable Clips to secure the cables.
OR
LOOSEN
Close the lever to lock the
Quickshift Donut in place.
Step 6. Adjust the Height of the Quickshift Donut
Step 7. Adjust the VESA Ball Mount
(Optional) Insert the Security Screw,
and tighten using a Phillips-head Screwdriver.
If necessary, adjust the tension
between the Donut and the Pole
using the 5mm Allen Key supplied.
Open the lever to loosen the
Quickshift Donut.
TIGHTEN
TIGHTEN
PUSH
Step 8. Cable Management
3mm Allen Key
Tension Plate
Position your Display to the desired viewing angle using
the ±20° tilt allowed by the VESA Ball Mount.
To make any adjustments, use the 3mm Allen Key
supplied. Apply half a turn at a time to each screw on the
Tension Plate to adjust evenly.
If the display does not hold its position, or is too resistant,
adjust the Tension Plate located at the rear of the VESA
Ball Mount.
Check the display, and the adjust again if necessary.


Produktspezifikationen

Marke: Atdec
Kategorie: Nicht kategorisiert
Modell: VFS-DV
Befestigungstyp: Tisch/Bank
Höchstgewichtskapazität: 12 kg
Schwenkbereich: -40 - 40 °
Neigungswinkelbereich: -40 - 40 °
Projektionsflächenkapazität: 24 "
Drehungswinkel: 360 °
Gewicht (imperial): 26.5 Pfund
Montageschnittstelle: VESA 75mm x 75mm / 100mm x 100mm / 200mm x 100mm

Brauchst du Hilfe?

Wenn Sie Hilfe mit Atdec VFS-DV benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Atdec

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-