Atdec TH-3060-LPF Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung fĂŒr Atdec TH-3060-LPF (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂŒr 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
Nylon Anchor (x2)
Dry Wall anchor (x4)
M5/6/8 Washer
(x4 each)
M5x30/16mm (x4 each)
M6x30/16mm (x4 each)
M8x30/16mm (x4 each)
Display Mounting
Screws
M4/5 Spacer (x4)
M6/8 Spacer (x4)
Wall Plate
10mm(
3
8") Hole
Dry Wall Anchor
Dry Wall Anchor Screw
Note:
Each Dry Wall anchor should be at a
maximum distance from the next anchor point.
This is the recommended mounting pattern for
Dry Wall Anchors.
Coach Screw
Wall Plate
10mm(
3
8") Hole
Nylon Anchor
6mm(
1
4") Hole
Timber Stud
Wall Plate
Coach Screw
Note:
Use a stud finder to accurately locate
the centre of the stud. Ensure that all two
screws fix securely into the stud.
Hardware
Coach Screw (x2)
Components Checklist
Wall Plate
Display Bracket (x2)
IMPORTANT INFORMATION
! IMPORTANT - Install 3060 Wall Mount as per Installation Instructions.
! This product supports a maximum load of 65kg (143.3lbs).
! This product supports displays with mounting hole configurations from 100mm (4”) to 500mm (19œ”) high,
and from 200mm (8”) to 810mm (32”) wide.
! The manufacturer does not accept responsibility for incorrect installation.
! Before installing this product, please check the display ventilation requirements with your
LED/LCD manufacturer.
Step 1. Check Components
Step 2. Mounting the Wall Plate
10mm ( drill bit
3
8
")

Spirit Level

Tools Required:
Power Drill

6mm
(
1
4
")
drill bit

Phillips Head screwdriver 
10mm
(
3
8
")
masonry drill bit
Large Flat Head Screw Driver
13mm
(
1
2
")
Socket Wrench or Shifter

Dry Wall
Tip: Use a spirit level to ensure wall plate is horizontal.
Masonry Wall
Timber Stud
OR OR
Check you have received all parts against the component checklist and Hardware above.
Installation Instructions
Hook Plate
Wall Plate
Note:
To access cable ports,
fold out screen tilt supports.
screen tilt support
Cut Release Ties so that they cannot
be seen from front of screen.
Spacer
(optional, used only for
recessed mounting holes)
Mounting Screw
Bracket
Washer
Back of Display
TOP
Hook Plate
Tip: If Hook Plates obstruct mounting
holes, remove and reposition
(as shown below.)
Hook Plate Screw
Use a large flat blade screwdriver
to remove/replace the two Hook
Plate screws.
Step 3. Attaching Brackets to Display
No portion of this document or any artwork contained herein should be reproduced in anyway without the express written consent Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without noticed. Published 14.10.10 ©
With the Brackets attached to the Display,
lower the Hook Plates onto the Wall plate.
Listen for "CLICK" to ensure the catch has
engaged.
Slide Display to desired position.
Step 4. Attaching/Detaching Display to Wall Plate (2 people required)
Step 5. Cable Management
Installation Complete
Detaching Display from Wall Plate:
To detach Display from wall plate, pull and
hold Release Ties to disengage locking
mechanism. Then lift the Display to unhook
from the wall plate.
Fold Tilt Supports back
once all
cables have been installed.
Power Cable
Release Tie
Note: Ensure that both
Release Ties are closest
to the outside edge of
the Display.
Release Tie


Produktspezifikationen

Marke: Atdec
Kategorie: Nicht kategorisiert
Modell: TH-3060-LPF

Brauchst du Hilfe?

Wenn Sie Hilfe mit Atdec TH-3060-LPF benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Atdec

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂŒr -Kategorien-