Atdec VF-AT-NK Bedienungsanleitung

Atdec Nicht kategorisiert VF-AT-NK

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Atdec VF-AT-NK (3 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 54 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/3

Handgrip Tab

Installation Instructions

VF-AT-NK

Component Checklist

Focus | Notebook Mount Accessory

Primary Arm

Cable Cover

Secondary Arm

Cable Cover

Hand Grip

Notebook Tray and Arm Assembly

! IMPORTANT - Install Visidec Focus Notebook Mount as per installation instruction.

! This product is designed to be used in conjunction with an external keyboard and mouse.

! To b used with existing Visidec Focus Mount.

! Visidec Focus Notebook Mount supports Notebooks up to 18”, weighing up to 8kg (17.6lbs).

! The manufacturer accepts no responsibility for incorrect installation.

IMPORTANT INFORMATION:

Step 1. Check Components

Check what you have received against the component checklist and hardware above.

Step 2. Remove existing Arm & Monitor from Visidec Pole (ensure monitor cables are unplugged)

Step 3. Remove existing Arm & Monitor from Visidec Pole (ensure monitor cables are unplugged)

5mm Allen Key

Notebook Tray

& Arm Assembly

Pole Top Cap

2.1 Remove Pole Top Cap

and 5mm Allen Key from

the Visidec Pole.

3.1 Slide the Handgrip onto

the top of the Visidec Pole so

the Handgrip Tab protrudes.

2.2 Whilst supporting the weight of the

Monitor, unlock the Hand Grip.

3.2 Slip the Notebook Tray & Arm

Assembly over the Handgrip Tab and

then onto the Pole.

2.3 Lift the Monitor and Focus Arm,

removing both from the Visidec Pole.

3.3 Slide the Arm Assembly and

Handgrip down the pole before locking

the Handgrip at the desired height.

Hook & Loop

Fasteners (x4 sets)

LIFT

6.2 Cable Clips and Cable Stops can be installed to further manage cables.

Please See Over.

Step 4. Re-install the existing Arm and Monitor

Step 5. Install Notebook

Step 6. Cable Management

6.1 After plugging in your cables, install the Cable Covers.

A. Insert Cable Covers up

into Lock Slots.

B. Push Cable Covers away

from Elbow Joint to secure

in place.

Elbow Joint

‘click’

Lock Slot

Note: After connecting the

Notebook Cables, route

them through the Cable

Management Clip on the

back of the Notebook Tray.

Note: Ensure enough

cable slack is given to

allow for movement.

5.1 Adjust the Support Tabs to suit the

width of the Notebook Computer ensuring

that cable ports are not obstructed.

5.2 To increase stability, use the self adhesive

Hook-and-Loop Fasteners supplied.

• Peel off the backing paper to the fasteners.

• Attach fasteners to both the Notebook Tray

and Computer.

• Ensure that each set of fasteners are correctly

aligned i.e. Hook to Loop.

4.1 Slide the existing

Arm and Monitor onto

the Visidec Pole.

4.2 Lock the Monitor

Arm Handgrip in the

desired position.

4.2 Lock the Monitor

Arm Handgrip in the

desired position.

5mm Allen Key

Pole Top Cap

10º - 20º

5º 15º

Allen Key

Storage

PAN (tray angle left/right)

Loosen

TILT (tray angle up/down)

Tighten

Loosen

Tighten

Installation Complete

Step 7. Adjusting the Display Bracket

Ergonomic Guidelines

Many experts believe that the extended use of any computer screen has the potential to cause serious injury to your eyes,

neck and back. This can be largely avoided by correctly positioning your display.

Viewing angle: Ergonomists recommend that the optimal position

of your display should be slightly below eye level. When looking at

the display’s centre the user should have a downward visual angle

of approximately 10°-20°.

Height: (h) As a guide, the height of your display should

approximately be as follows:

- Tall Male (Max): 560mm (22”)

- Short Male (Min): 368mm (14.5”)

- Tall Female (Max): 520mm (20.5”)

- Short Female (Min) 356mm (14”)

Distance: For visual comfort, a viewing distance (d) between

500mm (20”) to 750mm (29.5”) is recommended.

Tilt Angle: Angular adjustments to reduce reflection on your

monitor should range between 5° forward tilt to 15° backward tilt.

No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.

Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 11.12.13 ©

±5° Horizontal

Adjustment ±95° Portrait/

Landscape

Rotation

±25° Tilt

Adjust the tilt angle of the Notebook Tray as

desired, locking it in position using the 5mm

Allen Key.

The height can be adjusted by unlocking

the Handgrips (see Step 7). For the optimal

position of your display, refer to the

Ergonomic Guidelines below.

Produktspezifikationen

Marke:	Atdec
Kategorie:	Nicht kategorisiert
Modell:	VF-AT-NK
Höhenverstellung:	340 mm
Höchstgewichtskapazität:	17.5 kg
Paketgewicht:	1814.36 g
Schwenkbereich:	-90 - 90 °
Neigungswinkelbereich:	10 - 35 °
Projektionsflächenkapazität:	18 "
Verpackungsabmessungen (BxTxH):	360 x 320 x 130 mm