Atdec VF-AT-AA Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Atdec VF-AT-AA (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 29 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
Articulated Arm
UP
M4x10mm
(4x)
M4x12mm
(4x)
M4x16mm
(4x)
Display Mounting
Screws
Hand Grip
Primary Arm
Cable Cover
Secondary Arm
Cable Cover
Hardware
Pole Top Cap
Pole of the existing Visidec
Focus Product
A. Slightly insert Articulated Arm.
D. Twist and lock the
Hand Grip.
Pole
Articulated Arm
Lip of the Pole
Hand Grip tab
Installation Instructions
VF-AT-AA
Component Checklist
IMPORTANT:
The "User Operating
Card" must be left with
Visidec Focus Articulated
Arm once installed.
IMPORTANT INFORMATION:
Step 1. Check Components
Check you have received all parts against the Component Checklist and Hardware above.
Step 2. Remove Top Cap
Step 3. Attached Articulated Arm to the Existing Visidec Focus Product
B. Hold Articulated Arm at the lip
of
the pole and insert Hand Grip tab
in
the Articulated Arm.
Ensure the tab lines up with the slot
in the Pole.
C. Slide down Articulated
Arm with Hand Grip to
the desired position.
! IMPORTANT - Install Visidec Focus Accessory Arm as per Installation Instructions.
! This product is designed to be installed onto an existing Visidec Focus pole mount.
! This products supports displays with a maximum weight of 8kg (17½ lbs), and VESA mounting hole configurations:
75 x 75mm (3" x 3"), 100 x 100mm (4" x 4").
! The manufacturer accepts no responsibility for incorrect installation.
Focus Accessory Arm
Note: DO NOT
OVER TIGHTEN
M4 Display Mounting Screws M4 Display Mounting Screws
A. Insert Tabs
B. Push In
To insert Cable Covers:
Pull out
tabs
INSERT
NOTE: If the Articulated Arms are
to be used in a multi-user
environment, use the Cable Clip
(supplied with the Visidec Focus
Mount) to secure the cables to
the pole.
Installation Complete
Step 6. Cable Management
- Ensure arm is fully extended
Step 5. Replace Top Cap
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without noticed. Published 06.09.12
Step 4. Fasten Display to Articulated Arm
For displays with 75 x 75mm
(3" x 3") mounting hole patterns
For displays with 100 x 100mm
(4" x 4") mounting hole patterns
INSERT
Route the Cables underneath the Arms,
inserting the Primary and Secondary Arm
Cable Covers to hold the Cables in place.
INSERT
Primary Arm
Cable Cover
TIP:
Leave enough slack
in the cables at the joints
to allow full movement.
C. Then Push Up
Secondary Arm
Cable Cover
Insert cables into the
pole slot using the
Cable Balls (supplied
with
the Visidec Focus
Mount) to hold them in
place.


Produktspezifikationen

Marke: Atdec
Kategorie: Nicht kategorisiert
Modell: VF-AT-AA

Brauchst du Hilfe?

Wenn Sie Hilfe mit Atdec VF-AT-AA benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Atdec

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-