Atdec VF-AT Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Atdec VF-AT (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 21 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
Installation Instructions
VF-AT
Component Checklist
Focus | Articulated Arm
M4x10/12/16mm (x4)
Phillips Head Mounting Screws
Primary Arm
Cable Cover
Cable Stops
(x2)
Pole Top Cap Cable Clip
Secondary Arm
Cable Cover
M8x30mm
Screw
Bolt Through
Base
Steel Washer
Arm Assembly
Pole Assembly Desk Clamp Assembly
5mm Allen Key
HARDWARE Display Mounting
Screws
! IMPORTANT - Install Visidec Focus Articulated Arm as per installation instruction.
! This product supports a maximum load of 8kg (17.6lbs).
! The manufacturer accepts no responsibility for incorrect installation.
IMPORTANT INFORMATION:
Step 1. Check Components
Check what you have received against the component checklist and hardware above.
Step 2. Mount Pole Assembly
Option 1 Option 2: Bolt Through : Mount using Desk Clamp
Pole Assembly
Pressure Plate
2.1 Remove both the Pressure
plate and M10 Desk Clamp
Screw.
2.2 Fasten the Desk Clamp to the Bolt
Through Base & Pole Assembly using the
M8 x 30mm Screw and Tighten Firmly.
M10 Desk Clamp
Screw
M8 x 30mm Screw
Bolt Through Base
Pole Assembly
Slot
Slot Tab
Bolt Through Base
Steel Washer
M8x60mm Screw
5mm Allen Key
It is recommended that the Pole Assembly be
mounted towards the rear edge of the work surface.
Note: Ensure that the Slot Tab in the Bolt
Through Base fits snugly into the Slot on the
Pole Assembly.
The Visidec logo on the Bolt Through Base
must face the of this assembly.front
5mm Allen Key
5mm Allen Key
M8x60mm
Screw
Step 2. Mount Pole Assembly (cont.)
Step 3. Mount Arm Assembly
2.4 Remove the M8 x 16mm Socket Head Countersunk
Screws to release the Desk Clamp Bracket.
2.3 The Desk Clamp bracket can be repositioned to suit different mounting
surface thicknesses. The maximum mounting surface thicknesses supported
are listed below from the Top to Middle and Bottom Screw Holes.
T TM MB B
M8 x 16mm Socket
Head Countersunk
Screw
5mm Allen Key
Desk Clamp Bracket Pressure Plate
Table Top
M8 x 16mm Socket
Head Countersunk
Screw
M10 Desk Clamp Screw
5mm Allen Key
5mm Allen Key
5mm Allen Key
Arm Assembly
Pole Top Cap
2.5 Place in desired
location.
If you need to reposition the desk clamp bracket or you have no
access to the rear of your table continue to . Step 2.4
If you DO NOT need to reposition the desk clamp bracket and
you have access to the rear of your table skip to .Step 2.7
2.6 Reattach Desk
Clamp Bracket.
2.7 After positioning
your Pole Assembly,
screw Pressure Plate in
and Tighten Firmly.
3.1 Unlock Handgrip
and raise so that
Handgrip Tab
protrudes.
3.2 Slip the Arm
Assembly over the
Handgrip Tab and then
onto the Pole.
3.3 Slide the Arm
Assembly and Handgrip
down the pole before
locking the handgrip at
the desired height.
3.4 Insert Pole Top
Cap into Pole. This is
also where the Allen
Key is stored.
Desk Clamp Bracket
Handgrip Tab
Top 0 - 32mm (default)
Middle 7 - 47mm
Bottom 22 - 62mm
Top 29 - 69mm
Middle 43 - 84mm
Bottom 59 - 99mm
6.2 Cable Clips and Cable Stops can be
installed to further manage cables.
Please See Over.
Step 4. Mount Displays
Step 5. Adjust Height
M4 Phillips Head
Mounting Screws
Option 1: 75x75mm Hole Pattern 100x100mm Hole PatternOption 2:
Note: Extend Arms to
achieve 100x100mm
hole pattern.
5.1 Unlock Handgrip ensuring both the
screen and arm assembly are supported.
5.2 Lift/Lower the Screen to the desired height.
Move both Screen and Arm assembly together.
Step 6. Cable Management
6.1 After plugging in your cables, install the Cable Covers.
A. Insert Cable Covers up
into Lock Slots.
B. Push Cable Covers away
from Elbow Joint to secure
in place.
Elbow Joint
‘click’
‘click’
Lock Slot
Cable Stop
Cable Clip
5.3 Lock Handgrip firmly.
Note: Ensure enough cable
slack is given to allow for
movement.


Produktspezifikationen

Marke: Atdec
Kategorie: Nicht kategorisiert
Modell: VF-AT

Brauchst du Hilfe?

Wenn Sie Hilfe mit Atdec VF-AT benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Atdec

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-