Atdec Ultra Slim TH-3060-LPT Bedienungsanleitung

Atdec Nicht kategorisiert Ultra Slim TH-3060-LPT

Lesen Sie kostenlos die ๐Ÿ“– deutsche Bedienungsanleitung fรผr Atdec Ultra Slim TH-3060-LPT (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fรผr 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
Wall Plate
Coach Screw
6mm (ยผ") hole
Timber Stud
Nylon Anchor (x4)
M5/6/8 Washer
(x4 each)
M5x30/16mm (x4 each)
M6x30/16mm (x4 each)
M8x30/16mm (x4 each)
Display Mounting
Screws
M4/5 Spacer (x4)
M6/8 Spacer (x4)
Note: Use a stud finder to accurately locate the center of
the stud. Ensure that all two screws fix securely into the stud.
Hardware
Coach Screw (x4)
Installation Instructions
TH-3060-LPT
Components Checklist
Flat Screen Wall Mount | Tilt
Wall Plate
Tilt Bracket (x2)
IMPORTANT INFORMATION
! IMPORTANT - Install Telehook 3060 Wall Mount as per Installation Instructions.
! This product supports a load from 8kg (17.6lbs) min. to 5
0kg (110lbs) max.
! This product only supports displays with mounting hole configurations from 200mm x 100mm min.
to 800mm x 500mm max.
! The manufacturer does not accept responsibility for incor
rect installation.
! Before installing this Telehook product, please check the
display ventilation requirements with your
LED/LCD manufacturer.
Step 1. Check Components
Step 2. Mounting the Wall Plate
Tools Required:
๎˜‚๎˜ƒ
Power Drill
๎˜‚๎˜ƒ
6mm (ยผ") drill bit
๎˜‚๎˜ƒ๎˜„๎˜…๎˜†๎˜‡๎˜‡๎˜†๎˜ˆ๎˜‰๎˜ƒ๎˜Š๎˜‹๎˜Œ๎˜๎˜ƒ๎˜‰๎˜Ž๎˜๎˜‹๎˜๎˜๎˜๎˜†๎˜‘๎˜‹๎˜๎˜ƒ
๎˜‚๎˜ƒ
10mm (3/8") masonry drill bit
๎˜‚๎˜ƒ๎˜’๎˜Œ๎˜๎˜“๎˜‹๎˜ƒ๎˜”๎˜‡๎˜Œ๎˜•๎˜ƒ๎˜Š๎˜‹๎˜Œ๎˜๎˜ƒ๎˜‰๎˜Ž๎˜๎˜‹๎˜๎˜๎˜๎˜†๎˜‘๎˜‹๎˜
๎˜‚๎˜ƒ
13mm (ยฝ") Socket Wrench or Shifter
Tip: Use a spirit level to ensure wall plate is horizontal.
Masonry Wall
Timber Stud
OR
Check you have received all parts against the Component Checkli๎˜‰๎˜•๎˜ƒ๎˜Œ๎˜–๎˜๎˜ƒ๎˜Š๎˜Œ๎˜๎˜๎˜๎˜Œ๎˜๎˜‹๎˜ƒ๎˜Œ๎˜—๎˜˜๎˜‘๎˜‹๎˜™
Tension Tool
Wall Plate
Coach Screw
Nylon Anchor
10mm (
3/8
") hole
๎˜‚๎˜ƒ๎˜š๎˜›๎˜œ๎˜œ๎˜ƒ๎˜
3/8
") drill bit
๎˜‚๎˜ƒ
Spirit Level
Self-adhesive
Foam Pad
Push bottom of Display to lock the
Display to the Wall Plate. Listen
for a โ€˜CLICKโ€™.
Step 3. Attaching Tilt Brackets to Display
Step 4. Attaching/Detaching Display to Wall Plate (2 people required)
Step 5. Cable Management Step 6. Set Display Tilt
Tension Tool
TIGHTEN
LOOSEN
NOTE: If necessary use the supplied
Tension Tool to adjust the tension in
the tilt mechanism.
TOP
With the Tilt Brackets attached to
the Display, lower the Hook Plates
onto the Wall Plate.
1
2
15ยฐ TILT
OPTIONAL: For larger screens, fix the
protective self-adhesive foam pad (supplied) to
the back of the panel. Position on the bottom
edge, where the Display touches the wall.
Once the Display is securely fastened to the
Wall Plate cut or fold the Release Ties so that
they cannot be seen from front of screen.
Spacer
(OPTIONAL, used only for
recessed mounting holes)
Mounting Screw
Tilt Bracket (right)
Washer
Tilt Bracket (left)
Tension
Nut
NOTE: The Tilt Brackets must be
mounted to the Display with the
Tension Nuts facing outwards, so it
is easily accessible from the side.
1
HOOK
2
2
PUSH
Detaching Display from the Wall Plate
To detach Display from wall plate, pull and
hold both Release Ties to disengage the
locking mechanism.
Whilst pulling the Release Ties, lift the Display
to unhook from the Wall Plate.
Self-adhesive
foam pad (OPTIONAL)
PULL
Hook Plate
2
PUSH
HOOK
1
WALL
1
PULL
No portion of this document or any artwork contained herein should be reproduced in anyway without the express written consent from Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 16.02.11ยฉ
Installation Complete
Pull Display out from the wall to allow access to the cable
ports on the back of the panel.
Connect cables, and push Display back against the wall.
TIP: To push Display back against the wall, pull
bottom edge outwards then push Display backwards.
1 Holding the Display by the top and bottom edges,
pull the Display straight out from the wall.
2 Tilt Display downward as desired.


Produktspezifikationen

Marke: Atdec
Kategorie: Nicht kategorisiert
Modell: Ultra Slim TH-3060-LPT
Produktfarbe: Schwarz
Befestigungstyp: Wand
Hรถchstgewichtskapazitรคt: 50 kg
Farbe: Nein
Gehรคusematerial: Metall
Neigungswinkelbereich: -15 - 15 ยฐ
Projektionsflรคchenkapazitรคt: 32 "
Minimale VESA-Halterung: 200 x 100 mm
Maximale VESA-Halterung: 200 x 100 mm
Abstand zur Wand (min): 25 mm

Brauchst du Hilfe?

Wenn Sie Hilfe mit Atdec Ultra Slim TH-3060-LPT benรถtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Atdec

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fรผr -Kategorien-