Atdec TH-2040-VTR Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Atdec TH-2040-VTR (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
Component Checklist
Step 1. Component Checklist
Check you have received all parts against the Component Checklist above.
Mounting Fasteners
Wall Mount
Assembly (x1)
Step 2. Installing the Wall Mount Assembly (choose from one of the following options)
For mounting Telehook to a Timber Stud Wall - Using the Wall Mount Assembly Bracket, mark
the location of the 4 holes and drill using a 4mm drill bit. Secure the bracket to the wall using the M6 Coach
Screws as shown in diagram A.
For mounting Telehook to a Masonry Wall - Using the Wall Mount Assembly Bracket, mark
the location of the 4 holes and drill using an 8mm masonry drill bit. Secure the bracket to the wall using the M6
Coach Screws and Nylon Anchors as shown in diagram B.
A. Timber Stud Wall B. Masonry Wall
Note: This product will suit VESA compliant displays with 100x100mm, 200x100mm, and 200x200mm hole patterns only.
It will support up to a maximum weight of 25kg (55lbs).
TM
Installation Instructions
Flat Screen Wall Mount / Tilt
TH-2040-VTR
TOOLS REQUIRED:
• Power Drill
• Phillips-head Screwdriver
• 4mm (3/16) Drill Bit
• 8mm (5/16) Masonry Drill Bit
• 8mm (5/16) Socket Wrench
or Shifter
Combined 3mm
Allen Key and
Phillips-head
Screwdriver (x1)
Hardware
(Optional)
Security
Screw (x1)
M6 Coach
Screws (x4)
Nylon
Anchor (x4)
VESA
plate (x1)
Wall Mount Assembly
Bracket
M6 Coach
Screw
4 x 4mm
Holes
Wall Material
Stud
Wall Mount Assembly
Bracket
M6 Coach Screw
4 x 8mm
Holes
Masonry Wall
Nylon Anchor
M4x16mm / M4x25mm Screw (x4 each)
M5x16mm / M5x25mm Screw (x4 each)
M6x16mm / M6x30mm Screw (x4 each)
M8x16mm / M8x30mm Screw (x4 each)
M4/5
Washer (x4)
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 23.10.15 ©
Step 4. Attach your Display to the Wall Mount Assembly
Step 5.
Adjust the VESA Ball Mount
Installation Complete
Combined Phillips-head
Screwdriver/Allen Key
supplied
Step 3. Attach the VESA plate to your Display
Position your Display to the desired viewing angle, using the 20°
angular movement allowed by the VESA Ball Mount.
Depending on the weight of the display, it may be necessary to make
adjustments to the VESA Ball Mount. If the display does not hold its
position, or is too resistant, adjust the Tension Plate located at the
rear of the VESA Ball Mount (see diagram right).
To make any adjustments tension evenly using the 3mm Allen Key
supplied. Apply half a turn at a time to each screw on the Tension
Plate to adjust evenly.
Check the display, and then adjust again if necessary.
Tension
Plate
Loosen
(-Kg)
Tighten
(+Kg)
(Optional) Insert the Security Screw
supplied and tighten using a
Phillips-head Screwdriver.
Press and hold the Release Buttons.
Gently insert bottom of VESA Plate
into Quickshift Mount. Release
Buttons to lock
in place.
Security
Screw
Combined Phillips-head
Screwdriver/Allen Key
supplied
Hook the top of the VESA Plate onto
the VESA Ball Mount.
Back of Display
There are three mounting hole configurations:
• 100mm x 100mm
• 200mm x 100mm
• 200mm x 200mm
Choose appropriate Mounting Screws
from the Hardware supplied to suit
your Display.
Back of Display
Top of
Display
Mounting Screws (x4) Use M4/M5
Washers
where required
VESA plate
TIGHTEN


Produktspezifikationen

Marke: Atdec
Kategorie: Nicht kategorisiert
Modell: TH-2040-VTR

Brauchst du Hilfe?

Wenn Sie Hilfe mit Atdec TH-2040-VTR benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Atdec

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-