Atdec TH-1032-VFM Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Atdec TH-1032-VFM (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
Masonry Wall
- Drill two 10mm (0.4”) diameter holes, 50mm (2”) deep.
- Secure the Mounting Plate to the wall using the Coach
Bolts and Concrete Anchors supplied.
Component Checklist
Coach Bolt (x2)
Concrete Anchor (x2)
M4/5 Spacer (x4)
Security Screw (x1)
3mm Allen Key
M4x16/25mm
(x4 each)
M5x16/25mm
(x4 each)
M6x16/30mm
(x4 each)
TH-1032-VFM
Flat Screen Wall Mount / Full Motion
IMPORTANT INFORMATION:
Step 1. Check Components
Check you have received all parts against the component checklist and Hardware above.
Step 2. Attaching Arm to the Wall
! IMPORTANT - Install 1032 Flat Screen Wall Mount as per Installation Instructions.
! This product supports a maximum load of 25kg (55lbs).
! This product supports VESA mounting hole configurations: VESA plate, 75x75mm, 100x100mm, 200x100mm,
and 200x200mm.
! The manufacturer accepts no responsibility for incorrect installation.
Display Mounting Screws
Hardware
Tools Required:
Power Drill
•
6mm (0.25”) Drill Bit
•
10mm (0.4”) Masonry Drill Bit
•
Phillips-head Screwdriver•
13mm (0.5”) Socket Wrench or Shifter
•
Remove the Arm from the packaging and open fully.
Un-clip the Wall Plate Cover and slide down the arm.
Slide the Wall Plate Cover back along
the arm, and push flat against the wall.
Wall Plate Cover
M4/M5 Washers
(x4 each)
M6/8 Spacer (x4)
M8x16/30mm
(x4 each)
Arm Assembly VESA Plate
- Drill two 6mm (0.25”) diameter holes, 50mm (2”) deep.
- Secure the Mounting Plate to the wall using the Coach
Bolts supplied.
Timber Stud Wall
OR
Back of Display
Mounting Screws (x4)
Washers (x4)
VESA Plate
Choose appropriate Mounting Screws and
Washers from the Hardware supplied
to suit your Display.
Installation Complete
Step 4. Attaching your Display to the Arm
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 01.10.15 ©
Step 3. Attaching the VESA Plate to your Display
Step 5. Cable Management
Step 6. Final Adjustment
Washer
Mounting Screw
Recessed Mounting
Holes or Display with a
Curved Rear Panel
If the Mounting Holes are
recessed into the back of the
Display, or the Display has a
curved rear panel, use the
appropriated Spacer Bushes
supplied to pack the
Mounting Holes.
Note: Ensure the VESA
plate is securely fixed
to the display.
VESA Plate
VESA Ball Mount
Ball Mount.
Insert the Security Screw, and tighten using the
Phillips-head Screwdriver.
TIGHTEN
Security Screw
Remove the Cable Covers as required using a Phillips-head
Screwdriver.
Cable Cover
Connect cables to your Display, and route along the arms.
Re-attach the Cable Covers to hold the Cables in place.
TIP: Leave enough slack in the cables
to allow full movement at the joints.
LOOSEN (-kg)
TIGHTEN (+kg)
Rotate the Display as desired, locking the
Display into position by tightening the
Tension Plate.
+/- 20°
angular tilt
360° infinite
horizontal rotation
Display
Top of Mounting Hole
Spacer
Hook the top of the VESA Plate onto the VESA
HOOK
Press and hold the Release Buttons. Gently push
bottom of VESA Plate into VESA Ball Mount.
Release Buttons to lock in place.
PUSH
Release Button Phillips-head Screwdriver
3mm Allen Key
Tension Plate
Position your Display to the desired viewing angle using the 40°
angular movement allowed by the VESA Ball Mount.
If the display does not hold its position, or is too
resistant, adjust the Tension Plate located at the
rear of the VESA Ball Mount.
To make any adjustments, use the 3mm Allen Key
supplied. Apply half a turn at a time to each screw
on the Tension Plate to adjust evenly.
Check the display, and then adjust again if necessary.


Produktspezifikationen

Marke: Atdec
Kategorie: Nicht kategorisiert
Modell: TH-1032-VFM

Brauchst du Hilfe?

Wenn Sie Hilfe mit Atdec TH-1032-VFM benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Atdec

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-