Atdec SD-SA-DK Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Atdec SD-SA-DK (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
Adjusting the Display
Component Checklist
Installation Instructions
SPACEDEC ACROBAT
SWING ARM
Single Arm
Swing Arm
Assembly (x1)
Tube Assembly (x1)
Base Casting (x1)
Cable Wrap
Applicator (x1)
Top Cap Tool (x1)
2.5mm Allen
Key (x1)
Spacer Tube
(x2)
Washer (x1)
M8 Interscrew (x1)
M8 Nyloc Nut (x1)
Cable Tube
Manager Clip (x1)
Cable Clip
(x2)
M4x16mm
Countersunk
Screw (x3)
Extension
Clip (x4)
Desk Clamp Box
Desk Clamp
Bracket (x1)
5mm Allen
Key (x1)
M8 Desk Clamp
Screw (x1)
Pressure
Plate (x1)
Component Checklist
A
Check you have received all parts against the Component Checklist above.
Bits Box
Assembling the Arm
B
Top Cap and
Threaded Rod
Arm Assembly
Internal Tube Post
Spacer
Tube
Spacer
Tube
Cable Manager
Tube Clip
H
As LCD Manufacturers are constantly releasing new monitor models, Atdec does not accept responsibility if the mounting hole pattern does not comply with the
international VESA standards. Due to continuing product development, the manufacturer reserves the right to alter specifications without notice.
Published: 12.04.07
Installation Complete
B.1. Disassemble the Tube Assembly B.2. Assemble the Swing Arm
You will need to disassemble the Tube
Assembly before assembling the Swing Arm
Top Cap and
Threaded Rod
Internal
Tube Post
Spacer
Tube (x2)
Assemble the Swing Arm as shown:
Mounting Fasteners
M4x10mm
Screw (x4)
M4x12mm
Screw (x4)
M4x16mm
Screw (x4)
Threaded Rod
and Top Cap
(x1)
Inner Tube Post
16mm Cable
Wrap (x1)
H.1. Adjusting the Ball Joint Resistance
The Acrobat Swing Arm comes factory set to support 6kg displays. Adjust the arm to suit the weight of your
display as shown in the following steps:
Depending on the weight of the monitor, it may
be necessary to make adjustments to the Ball Joint
Mechanism. If the monitor doesn’t hold its position or
is too resistant, adjust the four tension screws located
around the Ball Joint (see diagram on the right) using
the supplied 2.5mm Allen Key.
Check the display, and then adjust again if necessary.
NOTE: Be sure to adjust screws evenly.
Tighten
Loosen
Tension
Screws (x4)
Ball Joint
2.5mm
Allen Key
H.2. Adjusting the Pivot Head Resistance
It is possible to control the amount of resistance in the
Pivot Head to suit your display.
To increase the resistance of the Pivot Head to suit
heavier displays, use the 5mm Allen Key supplied in the
Desk Clamp Box to tighten the interscrew in a clockwise
direction.
To decrease the resistance of the Pivot Head to suit
lighter displays, loosen the interscrew in an
anti-clockwise direction.
NOTE: It is recommended the Pivot Head be
left at the factory setting for best performance.
Pivot Head
Interscrew
5mm Allen Key
Loosen
Tighten
H.3. Adjusting the Swing Arm/Gas Strut Resistance
3kg
Monitor
9kg
Monitor
Raise Gas
Strut to suit
lighter display
Arm
5mm
Allen key
Gas Strut
Lighter
Heavier
Lower Gas
Strut to suit
heavier
display
H.3.1. Depending on the weight of the monitor, it
may be necessary to adjust the arm. This can be
done by using the 5mm Allen Key supplied in the
Desk Clamp Box.
H.3.2. If the arm tends to automatically rise
or fall when the display is attached, it will be
necessary to make small adjustments to the gas
strut. (see diagram on the right)
H.3.3. If the arm tends to rise, the gas strut
position should be raised. If the arm tends to fall,
the gas strut position should be lowered.
Ergonomic Guidelines
G
Ergonomists recommend that the optimal position of your screen should be slightly below eye level.
When looking at the screen’s centre the user should have a downward visual angle of approximately
10°-20°. As a guide, the height (h) of your display should approximately be as follows:
Tall Male (Max): 560mm (22”) Tall Female (Max): 520mm (201/2”)
Short Male (Min): 368mm (141/2”) Short Female (Min): 356mm (14”)
For visual comfort, a viewing distance (d) between 500mm (19
1/2”) to 750mm (291/2”) is
recommended.
Angular adjustments to reduce reflection on your monitor should range between 5° forward tilt to 15°
backward tilt.
Desk Clamp
15°
5°
HORIZONTAL SIGHT LINE (d)
CENTRE OF SCREEN
10°-20°
Recommended Viewing Distance / Height
Recommended Mounting Position
50mm
(2”)
When mounting the Spacedec Acrobat Swing Arm, ensure the correct focal distance can be achieved
for ultimate visual comfort (Refer to Recommended Viewing Distance / Height below)
Desk Clamp Bolt Through
(h)
13mm (1/2”) hole
Base Casting
C.1. Desk Clamp
C.2. Bolt Through
Mounting Options
C
There are two Mounting Options: Desk Clamp and Bolt Through
To use the Desk Clamp (Suits desktop thicknesses of 12mm-38mm [1/2”-1
1/2”]) follow the Desk Clamp
instructions at C.1. To use the Bolt Through system (Suits desktop thicknesses of 12mm-40mm [1/2”-11/2”])
follow the Bolt Through instructions at C.2.
To assemble the Desk Clamp Assembly, first place
the M8 Nyloc Nut inside the Base Casting with
the Plastic Ring facing down, then screw the Base
Casting on to the Desk Clamp Bracket using the
M4x16mm Countersunk screws.
C.1.1. Assemble the Desk Clamp
C.1.2. Attaching the Desk Clamp
Tighten
Firmly
Washer
M8 Interscrew
5mm Allen Key
Threaded
Rod
Base
Casting
Top Cap
Tool
Base Casting
Desk Clamp
Assembly
Desk Top
Pressure Plate
M8 Desk Clamp Screw
5mm Allen Key
Attaching the Display
D
Direct Mount Configuration
75mm x 75mm (3” x 3”) mounting hole pattern 100mm x 100mm (4” x 4”) mounting hole pattern
Installing Cable Management
E
Attaching the Cable Wrap to the Arm
F
E.1. Push the two supplied Cable Clips into the holes on the underside of the arm as shown in diagram
E.2. Feed the cables into the Cable Wrap Applicator.
E.3. Insert the Cable Wrap Applicator into the Cable Wrap as shown.
E.4. Squeeze the nose of the Applicator and place inside the Cable Wrap ensuring that the opening edges
of the Cable Wrap face towards the nose of the applicator as shown in diagram.
F.1. Position the display at its highest possible position to ensure that there is sufficient cabling at the end of
the arm so the cables are not stretched or pulled out when the display is moved.
F.2. Clip the cable wrap into the Cable Tube Manager Clips as shown in diagram.
BEFORE PROCEEDING TO THE NEXT STEP PLEASE NOTE:
Swing Arm will only work when a display is properly installed.
DO NOT adjust tension screws or gas strut until your display has been attached.
Cable Clips
Display at
highest point
Cable Tube
Manager Clip
Cable Wrap
E.1.
Push in
Clips
NOTE:
Ensure that
the flat side of
each Extension
Clip sits against
the back of the
display
Extension Clip
4x12mm or
4x16mm Screws
Display
4x10mm
Screws
C.2.1. Drill Mounting Hole
Drill a 13mm (
1/2”) hole in your work surface
at the desired location for your arm.
C.2.2. Install as shown
Insert the M8 Interscrew up through the hole in
the work surface.
Using both hands, secure the M8 Interscrew
with the 5mm Allen Key supplied in the Desk
Clamp Box and use the other hand to tighten
the Threaded Rod into the Interscrew with the
supplied Top Cap Tool.
F.1.
75mm
(3”)
75mm (3”)
100mm
(4”)
100mm (4”)
Nose
E.2. E.3. E.4.
F.2.
Adjust the Desk Clamp to suit your desk
thickness by turning the M8 Desk Clamp
Screw with the supplied 5mm Allen Key
Suits 12mm
(1/2”) to 38mm
(1
1/2”) thick
Work Surfaces
Pressure Plate
M8 Desk
Clamp Screw
Display
M4x16mm
Countersunk
Screw (x3)
Base
Casting
M8 Nyloc
Nut
Desk
Clamp
Bracket
C.1.3. Attaching the Swing Arm Post
Use the Top Cap Tool to tighten the Threaded Rod
into the Base Casting as shown below:
Top Cap
Tool
Threaded
Rod
Base
Casting
NOTE: Desk Clamp
Assembly is suitable for
square edged desks only.
Plastic
Ring
Tighten
Firmly
Tighten
Firmly
NOTE: It is
recommended
that the Desk
Clamp be
attached to the
rear or side
edge of the
work surface
DESK CLAMP ADJUSTMENT RANGE
13mm (1/2”) hole


Produktspezifikationen

Marke: Atdec
Kategorie: Nicht kategorisiert
Modell: SD-SA-DK

Brauchst du Hilfe?

Wenn Sie Hilfe mit Atdec SD-SA-DK benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Atdec

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-