Atdec SD-POS-VBM-B2B Bedienungsanleitung

Atdec Nicht kategorisiert SD-POS-VBM-B2B

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Atdec SD-POS-VBM-B2B (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
Component Checklist
3mm Allen Key
M4x12mm (x4)
M4x16mm (x4)
VESA Plate (x1)
M4x10mm (x4)
Security Screw (x1)
Installation Instructions
SD-POS-VBM-B2B
IMPORTANT INFORMATION:
Step 1. Check Components
Step 3. Undo and Remove Back Pin
Step 4. Install Back to Back VESA Ball Mount
! IMPORTANT - Install Spacedec POS Multi Back to Back as per Installation Instructions.
! This product supports a maximum load of 20kg (44lbs).
! This product supports VESA mounting hole configurations: 75x75mm and 100x100mm.
! The manufacturer accepts no responsibility for incorrect installation.
Display Mounting
Screws
Hardware
Check you have received all parts against the component checklist and Hardware above.
Back to Back
VESA Ball Mount
Step 2. Preparation
Choose from one of the following options:
A. New POS Height Adjustable Back to Back Installation
Prior to installing a new POS Multi Back to Back Assembly,
you will need to:
Install a POS Height Adjustable product to the work surface
(refer to the SD-POS-HA Installation Instructions).
Remove the Top Cap (use a small screw driver).
OR
B. Back to Back Conversion
Prior to converting an POS Multi Assembly,existing
you will need to:
Remove the existing Display (TV/Monitor).
Remove the Top Cap (use a small flat screw driver).
Top Cap
Top Cap
Existing POS Height
Adjustable Assembly
TIP: Be careful not to
damage the Top Cap.
Display l POS Multi Back to Back
NOTE: Phillips-head
screwdriver and Flat
screwdriver not supplied
3mm Allen Key
Grub Screw
LOOSEN
Using the 3mm Allen Key, undo the Grub Screw.
NOTE: This will be very tight
3mm Allen Key
Grub Screw
Back Pin
Remove the Back Pin but keep the Grub Screw for use later on.
REMOVE
3mm Allen Key
Back to Back
VESA Ball Mount
Grub Screw
Recess
TIGHTEN
Use the Grub Screw to Install the Back to Back VESA Ball Mount.
Ensure the Recess (shown) lines up with the Grub Screw before
tightening.
Grub Screws (x2)
Ensure both Grub Screws are tightened as firmly as possible.
(optional)
Top Cap
PUSH
Installation Complete
Step 6. Install Top Cap
C
No portion of this document or any artwork contained herein should be reproduced in anyway without the express written consent Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 03.07.13
Step 9. Attach your Display to the POS Assembly
Step 10. Adjust the VESA Ball Mount
Loop the Security Cable (Kensington or similar)
A.
around the internal post of the POS Assembly.
Feed the other end of the cable through the POS
B.
Assembly and out the Cable Management Hole.
After you have attached the monitor (As directed
C.
in Step 8) install the lock to the monitor as per the
manufacturer guidelines.
Note: Security Cable Not Included
Step 5. (Optional) Install Monitor Security Cable
Push down firmly to attach the Top Cap.
These Installation Instructions secure
the POS Multi using the provided
fasteners from the above work surface.
For advanced Security Installation from
below the work surface. Please refer to
the
Advanced Security Installation
Addendum.
Advanced Security Installation
HOOK
Back of Display
Quickshift Mount.
Hook the top of the VESA plate onto the
Press and hold the Release Buttons. Gently
push bottom of VESA Plate into Quickshift
Mount. Release Buttons to lock in place.
PUSH
Release Button Back of Display
TIGHTEN
Phillips-head
Screwdriver
Security Screw
Back of Display
Position your Display to the desired viewing angle using the 40 °
angular movement allowed by the VESA Ball Mount.
If the display does not hold its position, or is too
resistant, adjust the Tension Plate located at the
rear of the VESA Ball Mount.
To make any adjustments, use the 3mm Allen Key
supplied. Apply half a turn at a time to each screw
on the Tension Plate to adjust evenly.
Check the display, and the adjust again if necessary.
Tension Plate
3mm Allen Key
TIGHTEN (+kg)
LOOSEN (-kg)
Push out to remove
A.
Cable Access Cap
PUSH
Pull cables out through
B.
Rear Cable Access Port.
Step 8. Attach the VESA Plate to your Display
Step 7. Install Monitor Cables
Option 2: When you do not want to route the
cables below the work surface.
OUT
IN
OUT
Option 1:
There are two mounting
hole configurations:
• 75 x 75mm
• 100 x 100mm
Choose appropriate
Mounting Screws from
the Hardware supplied
to suit your Display.
Prior to attaching your monitor,
install the monitor cables.
Run them through the Front
Cable Access Port, down the
pole and out of the Cable
Access Hole in the work
surface.
VESA Plate
Mounting Screws (x4)
TOP OF
DISPLAY
Back of Display
75mm 75mm
100mm
ACCESS CAP
CABLE
100mm
Insert the Security Screw, and
tighten using a Phillips-head Screwdriver


Produktspezifikationen

Marke: Atdec
Kategorie: Nicht kategorisiert
Modell: SD-POS-VBM-B2B

Brauchst du Hilfe?

Wenn Sie Hilfe mit Atdec SD-POS-VBM-B2B benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Atdec

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-