Atdec Modular AWM-AHX-B Bedienungsanleitung

Atdec Nicht kategorisiert Modular AWM-AHX-B

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Atdec Modular AWM-AHX-B (3 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/3
AWM-AHX Page 1 of 3
Installation Guide
AWM-AHX
Heavy Duty Dynamic Arm
COMPONENT CHECKLIST REQUIRED TOOLS
All tools supplied
B
Lower Angled
Link
(x1)
A
Heavy Duty
Dynamic Link
(x1)
C
4mm
Allen Key
(x1)
WEIGHT RANGE
Desk Base Mount
6 - 16kg
(13 - 35 )lb
Post Mount
6 - 14kg
(13 - 31 )lb
Monitor weight should be
within the weight range of
all modular elements that
make up the complete
monitor mounting solution.
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! Curved monitors, deep devices (such as all-in-one PCs) and offset VESA locations exert additional leverage that can exceed
the capacity of the mount even though the monitor weight may be within the stated range.
! The manufacturer accepts no responsibility for incorrect installation.
! This product is compatible with AWM Series monitor arm products.
AWM-AHX Page 2 of 3
1.1 Push two arm links together
2.1 Push arm onto shaft
3.1 Push link
onto shaft
3.2 Ensure link
is fully pushed
onto shaft
3.3 Tighten set screw
1.2 Ensure arm is fully pushed together
2.2 Ensure arm is fully pushed onto base
1.3 Tighten set screw
2.3 Tighten set screw
1. Assemble Arm Links
2. Fit arm onto Arm Base (AWM-LB) or Channel Clamp (AWM-LC) (sold separately)
3. Fit Heavy Duty Tilt Head (AWM-LTH) or Dual Crossbar (AWM-LR) (sold separately)
Note: Check that arm rotation
is smooth after tightening
Note: Check that arm rotation
is smooth after tightening
Note: Check
rotation is smooth
after tightening
Optional: Set joint
rotation to 180°
on Arm Base or
Channel Clamp by
following separate
instruction manual.
To set up follow
separate installation
guide supplied with
the Dual Crossbar
Dual Crossbar
AWM-LR
Heavy Duty VESA Tilt Head
AWM-LTH
To set up follow
separate installation
guide supplied with the
Heavy Duty Tilt Head
AWM-AHX Page 3 of 3
Heavier
Monitor
Push
& Hold
Lighter
Monitor
4. Adjust arm tension
4.1 Use the provided allen key to adjust the arm tension
NOTE:
Hold arm in horizontal
position when adjusting
4.3 If the monitor sags or falls down,
increase the arms tension by rotating
the screw anti-clockwise.
4.5 If the monitor oats or hovers in all
positions the arm tension is balanced and
does not require further adjustment.
4.4 If the monitor springs upwards,
decrease the arms tension by rotating
the screw clockwise.
4.2 Installing multiple similar monitors?
1. Set up one monitor and record the
position of the marker on the gauge.
2. When installing other similar monitors,
pre-tension the arm to the recorded
marker position then ne-tune the
tension by following steps .4.3 to 4.5
Marker
Monitor Falls
(from top)
Increase Tension
Monitor ‘Floats’
(all positions)
Balanced
Monitor Springs
(from bottom)
Reduce Tension
5. Cable management
5.1 Plug cables into the monitor and
route the cables down the arm using
the cable hooks and clips.
Important!
Ensure enough
cable slack is given
in this area to allow
for movement of
the monitor.
atdec.com | atdec.co.uk | atdec.com.au
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specications without notice. ©20190208
1
1
2


Produktspezifikationen

Marke: Atdec
Kategorie: Nicht kategorisiert
Modell: Modular AWM-AHX-B

Brauchst du Hilfe?

Wenn Sie Hilfe mit Atdec Modular AWM-AHX-B benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Atdec

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-