Atdec ADB-VWP Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Atdec ADB-VWP (6 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/6
ADB-VWP Page 1 of 6
Pop-out Video Wall Mount
! Important: The wall structure must
be capable of supporting at least ve
times the weight of the î›˝at-panel.
If not, the wall structure must be
reinforced.
COMPONENT CHECKLIST
Installation Guide
ADB-VWP
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! The manufacturer accepts no responsibility for incorrect installation.
REQUIRED TOOLS
• Power Drill
• 6.5mm (1/4 ”) Drill Bit
• 10mm (3/8
”) Drill Bit
• Phillips Head Screwdriver
• Stud Finder
• 1/2” Socket
• Socket Wrench
• Pencil
0 - 50 kg
(0 - 110lbs)
WEIGHT RANGE
A
M5x16mm
Screw (x4)
K
M8 Washer
(x6)
F
M8x30mm
Screw (x4)
C
M6x16mm
Screw (x4)
M
Anchor
(x6)
H
M5/M6
Washer
(x4)
D
M6x30mm
Screw (x4)
N
M8x13mm
Spacer
(x8)
I
M8x5mm
Spacer
(x8)
E
M8x16mm
Screw (x4)
O
M8x15mm
Screw (x4)
(installed)
J
5mm
Allen Key
(x1)
B
M5x30mm
Screw (x4)
L
Coach Bolt
(x6)
G
M8x50mm
Screw (x4)
Mounting Base
(x1)
Left and Right
Mounting Bracket
(x1)
600mmx400mm
Adaptor
(x2)
ADB-VWP Page 2 of 6
INSTALLATION SAFETY INSTRUCTIONS
CAUTION: THIS MOUNT IS INTENDED FOR USE ONLY
WITH THE MAXIMUM WEIGHTS INDICATED. USE WITH
DISPLAYS HEAVIER THAN THE MAXIMUM INDICATED MAY
RESULT IN INSTABILITY CAUSING POSSIBLE INJURY.
Do not attempt to install this product until all
instructions and warnings have been read and
properly understood.
Please keep these instructions for future reference.
Please check carefully to make sure there are no
missing or defective parts - defective parts must
never be used.
Atdec Pty Ltd, its distributors and dealers are not
liable or responsible for damage or injury caused
by improper installation, improper use or failure to
observe these safety instructions.
In such cases, all guarantees will expire.
GENERAL
Atdec Pty Ltd recommends that a professional AV
installer or other suitably qualified person install
this product. Great care must always be taken
during installation as most AV equipment is of a
fragile nature, possibly heavy and easily damaged if
dropped.
If you do not fully understand the instructions or
are not sure how to install this product safely, then
please consult a professional for advice and/or to
install this product for you. Failure to mount this
product correctly may cause serious injury or death
both during installation and at any time thereafter.
Do not mount any AV equipment that exceeds
the specific weight limit of the product you are
installing.
This weight limit will be clearly stated on each
product and its packaging and will vary from
product to product.
PRODUCT LOCATION
Please pay careful attention to where this product
is located. Check load capacity of wall prior to
installation as some walls are not suitable for
installation. Designed for indoor use, this mount is
suitable for public or home installation. If located
in a public or frequently populated area ensure
that the product is out of the immediate reach of
people. If any AV equipment is to be suspended
over the likely path or location of people then great
care should be taken to secure all parts of
the
installation from falling. If you install this product
on drywall it must be securely fixed to a wooden
stud, concrete block or other permanent structure
behind the drywall board.
Installing on drywall boards alone will not support
the weight of most AV equipment.
When drilling holes in walls it is essential to avoid
contact with electrical cables and water or gas
pipes contained within. Use of a good quality
live wire detector and hidden object locator is
therefore recommended.
Only drill into structures when you are sure it is
safe to do so.
FIXING HARDWARE
It is highly recommended that all wall fixing screws
be used where supplied and that the purpose of all
other fixing hardware is fully understood. In some
cases more AV equipment fixing hardware will
be supplied to accommodate different models of
equipment and set up configurations.
The installer must be satisfied that any supplied
fixing hardware is suitable for each specific
installation. If any fixing screws or included
hardware are deemed not sufficient for a safe
installation then please consult a professional or
your local hardware store.
HAZARD LIMITATION
When routing cables take advantage of any built
in cable management features that the product
might provide and ensure that all cables are tidy
and secure. Check to see that any moving aspect
of product can do so unhindered by any cabling.
Some products have moving parts and the
potential to cause injury through the crushing or
trapping of fingers or other body parts.
Particular attention to the nature of moving parts is
required especially when assembling, installing and
adjusting during set up.
Immediately after installations double-check that
the work done is safe and secure. Double-check
all necessary fixings are present and are of ample
tightness.
It is recommended that periodic inspections of
the product and its fixing points are made as
frequently as possible to ensure that safety is
maintained. If in doubt consult a professional AV
installer or other suitably qualified person.
ADB-VWP Page 3 of 6
Directional Mounting Arrow
The directional mounting arrow
stamped into the ADB-VWP mount
indicates which is the top edge.
L
K
1. Mounting to wooden studs
A. Two people are recommended for this step;
one person to level the mount and another
person to mark the wall stud location.
i Place the mount against the wall in the
desired viewing location.
ii Adjust the mount to align the mount slots in
the mount with the centre of the wall studs.
iii Level the mount.
iv Use a pencil to mark the upper right
mounting location along the centre of the
wall stud.
B. Two people are recommended for this step;
one person to level the mount and another
person to drill the pilot holes.
Drill a “pilot hole” in the centre of each of
the marks with a power drill and a 1/
4”
(6.5mm) drill bit.
C. Two people are recommended for this step;
one person to level the mount and another
person to fasten the screws.
i Insert one (1) coach bolt and one (1) M8
washer into each pilot hole.
ii Tighten all coach bolts using a socket wrench
and 1/2” socket.
Only use 1/
4” (6.5mm) drill bit
when drilling the pilot holes
Do not overtighten the coach bolts
when attaching the mount to the wall.
Improper installation may result in
personal injury or propery damage.
Orientation
Mounting Safety
Two people are recommended
to install the mount.


Produktspezifikationen

Marke: Atdec
Kategorie: Nicht kategorisiert
Modell: ADB-VWP

Brauchst du Hilfe?

Wenn Sie Hilfe mit Atdec ADB-VWP benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Atdec

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-