Ashdown Engineering HOD-600 Bedienungsanleitung

Ashdown Engineering Empfänger HOD-600

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Ashdown Engineering HOD-600 (7 Seiten) in der Kategorie Empfänger. Dieser Bedienungsanleitung war für 17 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/7
INPUT - There is a single instrument input provided linked to
a PASSIVE/ACTIVE selector switch. The Passive input (switch
out) is high sensitivity and also high impedance to suit the
output from PASSIVE basses. The Active input (switch in) is
low sensitivity and lower impedance to suit the output from
ACTIVE basses.
INPUT CONTROL - The INPUT control sets the signal level
through the preamp in conjunction with the INPUT LEVEL VU
Meter. This is adjusted to give a reading of 0VU on the meter
for average playing dynamics with occasional peaks into the
red region. Please note that the setting of this may have to be
re-adjusted after modiî› cation of the EQ controls.
PUSH FLAT / SHAPE - With this button in its OUT position a
î› xed E.Q. is superimposed on the preamp to give a bright but
punchy character to the sound. Pushing this button IN returns
the preamp to a Flat frequency response. This function may
also be controlled from a footswitch. For the footswitch to
operate this button must be in its OUT position.
DOOM - This routes the signal either through a clean Solid
State ampliî› cation section (control on zero) or through a
Dual Triode Tube ampliî› cation/overdrive section in order
to add either tonal character i.e. warmth with the control
set at 9 o’clock, a slight edge in the sound at 12 0’clock
through to an increasing degree of Tube distortion/over-
drive as the control is advanced to maximum.
A Mix of these two ampliî› cation sections can be achieved
with this control.
N.B. The degree of tube distortion provided by this control
will also depend on the setting of the INPUT control.
DOOM IN/OUT - This push button switches the valve drive
section IN or OUT. This function may also be controlled from
the Ashdown 4 way footswitch. For the footswitch to operate
this button must be in its OUT position.
E.Q. IN / OUT - This push button switches the Equalisation
section IN or OUT i.e. the Bass, Middle and Treble controls
plus the two sets of sliders placed between each of these.
WWW.ASHDOWNMUSIC.COM
HEAD OF DOOM USER GUIDE:

Produktspezifikationen

Marke: Ashdown Engineering
Kategorie: Empfänger
Modell: HOD-600

Brauchst du Hilfe?

Wenn Sie Hilfe mit Ashdown Engineering HOD-600 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Empfänger Ashdown Engineering

Ashdown Engineering

Ashdown Engineering CTM 300 Bedienungsanleitung

20 August 2024
Ashdown Engineering

Ashdown Engineering Original HD-1 Bedienungsanleitung

12 August 2024
Ashdown Engineering

Ashdown Engineering Tone Pocket V2.0 Bedienungsanleitung

10 August 2024
Ashdown Engineering

Ashdown Engineering HOD-600 Bedienungsanleitung

9 August 2024
Ashdown Engineering

Ashdown Engineering Rootmaster EVO-II Bedienungsanleitung

8 August 2024
Ashdown Engineering

Ashdown Engineering ABM EVO IV Bedienungsanleitung

13 April 2024

Bedienungsanleitung Empfänger

Neueste Bedienungsanleitung für -Kategorien-

Rotel

Rotel RA‑1592MKII Bedienungsanleitung

16 Oktober 2024
Denon

Denon AVR-S900W Bedienungsanleitung

16 Oktober 2024
Pro-Ject

Pro-Ject Amp Box DS2 Bedienungsanleitung

15 Oktober 2024
AKG

AKG HP12U Bedienungsanleitung

15 Oktober 2024
Sennheiser

Sennheiser EM 9046 SU Bedienungsanleitung

14 Oktober 2024
Yamaha

Yamaha MusicCast RX-V481 Bedienungsanleitung

14 Oktober 2024
JL Audio

JL Audio VX600/6i Bedienungsanleitung

12 Oktober 2024
Pioneer

Pioneer SX-303RDS Bedienungsanleitung

10 Oktober 2024
Technics

Technics SA-160L Bedienungsanleitung

8 Oktober 2024
Avantree

Avantree Audiplex Bedienungsanleitung

7 Oktober 2024