Artillery Sidewinder X1 Bedienungsanleitung
Artillery
3D-Drucker
Sidewinder X1
Lesen Sie kostenlos die ๐ deutsche Bedienungsanleitung fรผr Artillery Sidewinder X1 (2 Seiten) in der Kategorie 3D-Drucker. Dieser Bedienungsanleitung war fรผr 31 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/2

Ar๎llery 3D Printer
Sidewinder X1
๎๎ ๎ ๎ ๎ ๎๎๎ ๎ ๎๎ ๎ ๎๎ ๎ ๎ ๎ ๎ ๎
List 1 - Main Modules List 2 - Tools & Spares
M4x45 (5pcs)
Step 1
M4x45 (4pcs)
Fix the XZ gantry to the base with 4pcs of M4x45
screws as shown in the picture below.
Step 2
Fix the spool holder to the top of the printer, adjust
the width to ๏ฌt the size of your ๏ฌlament spool. Make
sure the ๏ฌlament sensor is facing forward.
Step 3
Connect the ๏ฌlament runout sensor as shown in
pictures below:
Step 4
Connect the Z endstop to the cable.
Step 5
Connect the Z Stepper Motors as shown in the
pictures below:
Front
30pin (1pc)
20pin (1pc)

With this reset bu๎ฉon, it will reset the machine and
cannot resume prin๎ng a๎er pressed, so be careful
not to press it accidentally.
TipsReset Bu๎ฉon
During prin๎ng, the LED near the nozzle shows the
current prin๎ng status:
- gradually change from blue to violet as the heated
bed gets to target temp.
- gradually change from violet to red as the hotend
gets to temperature.
- change to white to illuminate work surface.
- change to green once print has ๏ฌnished.
- turn o๏ฌ a๎er the print has ๏ฌnished.
Also, you can change the LED color or turn it o๏ฌ
through the TFT touch screen.
Step 6
Connect the X carriage and ๏ฌlament runout sensor as
shown in picture to the base. Cau๎on: Please handle
the ๏ฌexible ๏ฌat cable (FFC) with care, make sure it
goes straight in when plugging them in, and make
sure theyโre si๎ซng ๏ฌush inside the connectors.
Step 7
Connect the FFC to the board on X gantry.
Step 8
Adjust the tension of all the wheels on the machine. Try
to turn the wheels without forcing them. If the wheel
turns freely or without much e๏ฌort, then it is too loose.
To ๎ghten the wheels, rotate the eccentric nuts slightly
un๎l the wheel is snug against the frame.
Step 8
For wheels under build plate, push the wheels (on the
non-eccentric nut side) ๎ght against the aluminum
extrusion, then adjust the front and rear wheels by
turning the eccentric nuts, adjust the middle one at
last.
Step 9
Now you can connect power and turn on the machine.
On the touch screen, go to Tools -> Heat to pre-heat
the nozzle and bed. Wait ๎ll both heated up and
stead, go to Tools -> Level:
Move the nozzle to all four corners, adjust the height
by turning the knob below the bed. Slide an A4 paper
between the nozzle and the bed, adjust the height so
that the piece of paper slides, with just a bit of drag,
in all loca๎ons of the bed.
You may need to do the same process twice because
an adjustment in one corner will a๏ฌect others.
Last update date: 6 September, 2019
This manual is updated to the date of prin๎ng.
Please refer to the electronic version if in doubt.
Artillery 3D Technology Co., Ltd.
For detailed warranty policy, please visit
๎๎ฉ๎๎๎ฅ๎ฅฌ๎ฅฌ๎๎๎๎ฌ๎ฅ๎๎ฝ๎๎ฝ๎ฅ๎๎ฝ๎ต๎ฅฌ๎๎ฝ๎๎๎๎ฏ๎ฅฌ๎๎๎ถ๎ฝ๎๎ฝ๎ฅฌ๎ฌ๎๎ฅฌ
๎๎๎๎๎ฏ๎๎๎ฅฌ๎๎๎ถ๎ฝ๎๎ฝ๎ฅฒ๎ฏ๎๎ต๎๎๎๎๎ฅฒ๎๎๎๎๎๎ถ๎๎
๎ฆ๎ฝ๎๎๎๎ต๎๎๎ฝ๎๎๎ฅ๎๎๎ฏ๎๎๎๎๎๎๎๎๎๎๎๎ฝ๎ต๎๎๎๎๎ฌ๎๎๎ถ๎๎๎๎๎๎๎๎๎
๎๎ฉ๎๎๎ฅ๎ฅฌ๎ฅฌ๎๎๎๎ฌ๎ฅ๎๎ฝ๎๎ฝ๎ฅ๎๎ฝ๎ต๎ฅฌ๎๎ฝ๎๎๎๎ฏ๎ฅฌ๎๎๎ถ๎ฝ๎๎ฝ๎ฅฌ๎ถ๎๎๎๎๎ฌ๎๎
๎๎๎๎๎ฝ๎ต๎๎๎๎ถ๎๎๎๎๎๎๎๎ฝ๎ต๎๎๎ฆ๎๎๎๎๎ฝ๎ฝ๎ฌ๎๎๎๎ฝ๎ต๎๎๎๎
๎๎ฉ๎๎๎ฅ๎ฅฌ๎ฅฌ๎๎๎๎ฅ๎จ๎๎๎๎๎ฝ๎ฝ๎ฌ๎ฅ๎๎ฝ๎ต๎ฅฌ๎๎๎ฝ๎ต๎๎๎ฅฌ๎๎๎๎ฏ๎ฏ๎๎๎๎๎๎๎งญ๎ฅฌ
Customer SupportFacebook Page
Produktspezifikationen
Marke: | Artillery |
Kategorie: | 3D-Drucker |
Modell: | Sidewinder X1 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Artillery Sidewinder X1 benรถtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung 3D-Drucker Artillery

16 August 2024
Bedienungsanleitung 3D-Drucker
- 3D-Drucker Anker
- 3D-Drucker Exibel
- 3D-Drucker Gembird
- 3D-Drucker Velleman
- 3D-Drucker Renkforce
- 3D-Drucker Polaroid
- 3D-Drucker Weller
- 3D-Drucker Kodak
- 3D-Drucker CraftBot
- 3D-Drucker Flashforge
- 3D-Drucker German RepRap
- 3D-Drucker Monoprice
- 3D-Drucker Sindoh
- 3D-Drucker Bq
- 3D-Drucker Dimension
- 3D-Drucker Easy Threed
- 3D-Drucker GooVer
- 3D-Drucker MakerBot
- 3D-Drucker PP3DP
- 3D-Drucker XYZprinting
- 3D-Drucker Leap Frog
- 3D-Drucker BFB
- 3D-Drucker Wasp
- 3D-Drucker Anycubic
- 3D-Drucker Zortrax
- 3D-Drucker 3D Systems
- 3D-Drucker LulzBot
- 3D-Drucker Snapmaker
- 3D-Drucker Creality3D
- 3D-Drucker Creality
- 3D-Drucker Raise3D
- 3D-Drucker Wanhao
Neueste Bedienungsanleitung fรผr -Kategorien-

27 September 2024

5 September 2024

4 September 2024

3 September 2024

3 September 2024

2 September 2024

2 September 2024

1 September 2024

31 August 2024

31 August 2024