APC Symmetra LX Bedienungsanleitung

APC Batterie Symmetra LX

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für APC Symmetra LX (2 Seiten) in der Kategorie Batterie. Dieser Bedienungsanleitung war für 37 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

Symmetra LX

Start-Up Guide

Extended Run Cabinets

For use with Symmetra LX UPS models:

990-1873-001 04/2005

200V, 4–8 kVA

208/240V, 4–8 kVA

220/230/240V, 4–8 kVA

200V, 4–16 kVA

208/240V, 4–16 kVA

220/230/240V, 4–16 kVA

READ FIRST

This guide is applicable for the Symmetra LX tower and rack-mount

extended run cabinet models. These units provide extended run time for the

Symmetra LX tower or rack-mount UPS models.

See and retain the product documentation shipped with your system for

other important installation, operation, and maintenance instructions.

Illustrations are representative. The Symmetra LX configuration, including

components and optional APC equipment, may be different from the models

shown in this guide.

prohibited.

APC, the APC logo, InfraStruXure, PowerChute, Smart-UPS and Symmetra

are registered trademarks of American Power Conversion Corporation. All

other trademarks are the property of their respective owners.

9-Battery

Rack-mount

Extended Run

9-Battery

Tower

Extended Run

3-Battery

Rack-mount

Extended Run

Overview

1. Read Safety and General Information Instructions

2. Refer to the UPS Documentation

If installing the Symmetra LX and the Extended Run Cabinet(s),

install according to the instructions in the Symmetra LX Start-Up

Guide shipped with the UPS.

3. Install the Extended Run Cabinet(s)

Perform the physical installation for the extended run cabinet(s).

See the included Symmetra LX Physical Installation Guide.

4. Follow the proceeding Start-Up Instructions

See these instructions once the physical installation for the

Extended Run Cabinet(s) is complete. This section contains

information on how to connect, test, and start the unit.

Electrical

Hazard

• Read, understand and follow ALL safety

instructions contained in the Symmetra LX Safety

Instructions and General Information Guide.

• Failure to follow safety instructions and warnings

could result in equipment damage, serious injury,

or death.

Start-Up Instructions

1. Connect the first Extended Run Cabinet

1.1 Remove the screw and battery connector cover from the

back of the UPS.

1.2 Connect the power cable of the first extended run cabinet

to the UPS battery connector .

1.3 Set the dial of the extended run cabinet to ‘2’.

1.4 Connect the communications cable from the extended run

communications connector on the UPS to the connector on

the extended run cabinet .

Note

The illustrations shown in this section are applicable for the

tower and rack-mount extended run cabinets.

Note

If connecting to a UPS with integrated extended run, set the

dial of the first extended run cabinet to ‘3’ instead of ‘2’.

2. Connect additional Extended Run Cabinets

Connect each additonal extended run cabinet to the previously installed

cabinet. The Symmetra LX supports a maximum of seven cabinets.

2.1 Remove the screw and UPS battery connector panel from the

previously installed cabinet.

2.2 Connect the power cable from the new cabinet into the battery

connector of the previous cabinet.

2.3 Set the dial of the new cabinet to a number that is one higher

than that of the previous cabinet .

2.4 Connect the communications cable from the communications

connector of the new cabinet to that of the previous cabinet .

3. Verify Connection

3.1 Check that the green status light on the rear of each cabinet will light.

3.2 Check that the front display shows the correct dial number.

3.3 Refer to the status menu on the UPS PowerView display (see the

Symmetra LX Operations Guide) to verify that the number of battery

modules matches the total number of battery modules installed in the

UPS and all extended run cabinets. Also, verify there are no bad

battery modules present.

Note

• To verify the connection, the UPS must be on. For further

information, see the Symmetra LX Start-Up Guide.

• Messages regarding battery quantity may be visible on the UPS

PowerView display.

Troubleshooting

It is assumed that the Symmetra LX is powered and functioning during these startup

procedures. If the problem persists, call technical support. Visit the the APC website at

http://www.apc.com/support for contact information.

Problem Possible Cause Solution

The green status LED (rear

of frame), and the front

display (front of frame) do

not light after the

communication cable is

installed.

There is no battery power

present at the frame.

Check that the battery cable

and battery modules are

properly installed.

The communication cable is

not installed

Check that the

communication cable is

properly installed.

The green status LED

lights, but the front display

does not show the frame

number.

The display cable is not

connected.

See the Extended Run

Cabinet Physical Installation

Guide for proper cable

connection instruction.

There is a potential hardware

failure.

Call technical support.

The front display

continuously flashes on

and off.

More than one frame is set

with the same frame number.

Check that frame numbers

are not duplicated on the

communication card(s).

An “XR frame failure” is

reported. The front display

flashes an error code.

The “E_O” frame error code

may indicate that the battery

cable is not installed.

Check that the battery cable

is properly installed. If the

error code continues to flash,

call technical support.

The “E_7” frame error code

may indicate that the

communication cable is not

installed

Check that the

communication cable is

properly installed. If the error

code continues, call

technical support.

All other LED error codes

could indicate a potential

hardware failure.

Call technical support and

report the error code.

The front display

alternately flashes the

frame number and either

“Lx” , “Cx”, or “Rx”.

A failed battery module has

been detected in the location

displayed.

Replace the battery module.

To obtain a replacement

battery, see the APC

website.

The number of battery

modules reported is

inaccurate.

One or more battery module

disconnect switches are off

(opened).

Check that the disconnect

switch on all modules is

closed (counter-clockwise).

Battery modules are not

installed correctly.

Check that all battery

modules are properly

installed in the extended run

frame(s).

Produktspezifikationen

Marke:	APC
Kategorie:	Batterie
Modell:	Symmetra LX
Akku-/Batteriekapazität:	864000 mAh
Gewicht:	29100 g
Produktfarbe:	Silber
Akku-/Batterietechnologie:	Plombierte Bleisäure (VRLA)
Betriebstemperatur:	0 - 40 °C
Relative Luftfeuchtigkeit in Betrieb:	0 - 95 %
Paketgewicht:	32280 g
Zertifizierung:	CSA, UL 1778
Warentarifnummer (HS):	85079080
Temperaturbereich bei Lagerung:	-15 - 45 °C
Luftfeuchtigkeit bei Lagerung:	0 - 95 %
Akku-/Batteriespannung:	120 V
Batteriekapazität:	864 Ah
Formfaktor:	1U
Abmessungen (BxTxH):	210 x 546 x 140 mm
Verpackungsabmessungen (BxTxH):	286 x 750 x 385 mm
Batterie Lebensdauer:	3 Jahr(e)
Höhe bei Betrieb:	0 - 3000 m