Apantac SDI-FIB Bedienungsanleitung

Apantac Nicht kategorisiert SDI-FIB

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Apantac SDI-FIB (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

1. SDI-FIB-Tx: SDI to Fiber transmitter w/ DC5V

1.5A Power Supply

2. SDI-FIB-Rx: Fiber to SDI receiver w/ DC5V

1.5A Power Supply

3. DC 5V 1.5A Power Supplies

4. Options: 12V XLR male to mini XL female

cable for direct power from the camera

5. User Manual

6. Pelican like hard carrying case

Product Specification

 Transmission of Multi-rate SDI (3G/HD/SD-

SDI) video over a single fiber. (SMPTE-

424M, SMPTE-292M and SMPTE-259M)

 Compatible with single-mode or multi-mode

fiber

 Equalized on the inputs and reclocked on the

output to maximize performance up to 120m

for 3G and 140m for HD-SDI

 Extension limit: 18 mile (30 km) for 1.485

Mbps, 12.5 miles (20 km) for 3G (1080P)

 Recommended fiber optic cable: Glass single

-mode fiber with 1310, 1550nm with ST ter-

minated connectors

 General Electrical specifications

 Link power budget: Minimum 11dB

 BNC connectors: 75 ohm male

 Mechanical specifications

 Dimension: 19.5mm x 19.5mm x 82.7mm

(WxHxD)

 Environmental Specifications

 Operating temperature: -20C to 70C

 Storage temperature: -30C to 85C

 Humidity: 5% to 95% RH

MAZAMA

SDI-FIB

Installation and

Apantac LLC

7556 SW Bridgeport Road

Portland, OR 97224

T: +1 (503) 968 3000

F: +1 (503) 389 7921

E: info@apantac.com

3G/HD/SD-SDI to Fiber Extender

Mazama SDI-FIB 0817

What’s in the Box

DC Power Adaptor Pin-out

Startup and Installation

(1) Unpack the content from the hard carrying

case

(2) Connect the SDI-FIB-Tx’s BNC side to the SDI

source. (Note: It is recommended to connect

the BNC directly to the source. Any interme-

diate cables or barrows may impact the signal

performance)

(3) Plug the +5V DC power adaptor to SDI-FIB-

(4) Connect the SDI-FIB-Rx’s BNC to the display.

(Note: It is recommended to connect the BNC

directly to the source. Any intermediate ca-

bles or barrows may impact the signal perfor-

mance)

(5) Plug the +5V DC power adaptor to SDI-FIB-

Connection Diagram

there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause

harmful interference to other devices, which can be

determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by

one or more of the following measures:

 Reorient or relocate the receiving device.

 Increase the separation between the equipment.

 Connect the equipment into an outlet on a circuit dif-

ferent from that to which the other device(s) are con-

nected.

 Consult the manufacturer or field service technician for

help.

 Type of protection against electric shock: Class I equip-

ment

 Degree of protection against electric shock: Not classified

- no applied parts

 Classification according to the degree of protection

against ingress of water as detailed in the current edition

of IEC 529: IPX0, ordinary equipment

 This equipment is not suitable for use in the presence of

flammable anesthetics or oxygen

 Mode of operation: continuous operation

Warranty Information

1 One ( ) Year Warranty

Apantac warrants this fiber-optic 3G-SDI extension

product to be free from defects in workmanship and

materials, under normal use and service, for a period

of ( ) year from the date of purchase from One 1

Apantac or its authorized resellers.

If a product does not work as warranted during the

applicable warranty period, Apantac shall, at its option

and expense, repair the defective product or part,

deliver to customer an equivalent product or part to

replace the defective item, or refund to customer the

purchase price paid for the defective product.

All products that are replaced will become the property

of Apantac.

Replacement products may be new or reconditioned.

FCC/CE Statement

This device complies with part 15 of FCC Rules and EN

55022/61000-3 for CE certification. Operation is sub-

ject to the following two conditions: (1) this device

may not cause harmful interference, and (2) this de-

vice must accept any interference received, including

interference that may cause undesired operation. This

equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to part

15 and 2 of FCC Rules and EN 55022/61000-3 for CE

certification. These limits are designed to provide rea-

sonable protection against harmful interference when

the equipment is operated in a residential installation.

This equipment generates, uses, and can radiate radio

frequency energy and. if not installed and used in ac-

cordance with the instruction guide, may cause harm-

ful interference to radio communications. However,

there is no guarantee that interference will not occur

in a particular installation. If this equipment does

cause harmful interference to radio or television re-

ception, which can be determined by turning the

equipment off and on, the user is encouraged to try to

correct the interference by one or more of the follow-

ing measures:

 Re-orient or relocate the receiving antenna.

 Increase the separation between the equipment and

the receiver.

 Connect the equipment into an outlet on a circuit differ-

ent from that to which the receiver is connected.

 Consult a service representative for help.

Properly shielded and grounded cables and connectors

must be used in order to comply with FCC/CE emis-

sion limits. Changes or modifications not expressly

approved by the party responsible for compliance

could void the user s authority to operate the equip-

ment.

UL/IEC Statement

This equipment has been tested and found to

comply with the limits for medical devices in IEC

60601-1:1994. These limits are designed to provide

reasonable protection against harmful interference in a

typical medical installation.

This equipment generates uses and can radiate radio

frequency energy and, if not installed and used in ac-

cordance with the instructions, may cause harmful

interference to other devices in the vicinity. However,

Any replaced or repaired product or part has a ninety

(90) day warranty or the reminder of the initial war-

ranty period, whichever is longer.

Warranty Limitation and Exclusion

Apantac shall have no further obligation under the

foregoing limited warranty if the product has been

damaged due to abuse, misuse, neglect, accident,

unusual physical or electrical stress, unauthorized

modifications, tampering, alterations, or service other

than by Apantac or its authorized agents, causes oth-

er than from ordinary use or failure to properly use

the Product in the application for which said Product

is intended.

Dispose of Old Electrical & Electronic

Equipment

(Applicable in the European Union and other Europe-

an countries with separate systems)

This symbol on the product or on its

packaging indicates that this product

shall not be treated as household

waste. Instead it shall be handed over

to the applicable collection point for

the recycling of electrical and elec-

tronic equipment. By ensuring this product is

disposed of correctly, you will help prevent po-

tential negative consequences for the environ-

ment and human health, which could otherwise

be caused by inappropriate waste handling of this

product. The recycling of materials will help to

conserve natural resources. For more detailed

information about recycling of this product,

please contact your local city office, your house-

hold waste disposal service or the shop where

you purchased the product.

Produktspezifikationen

Marke:	Apantac
Kategorie:	Nicht kategorisiert
Modell:	SDI-FIB

Brauchst du Hilfe?

Wenn Sie Hilfe mit Apantac SDI-FIB benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Nicht kategorisiert Apantac

Apantac VD-Conv Bedienungsanleitung

5 September 2024

Apantac SDI-CVBS-S Bedienungsanleitung

1 September 2024

Apantac Micro-Single Bedienungsanleitung

1 September 2024

Apantac MicroQ Bedienungsanleitung

1 September 2024

Apantac HDM2.0-FIB-II-HID-SM Bedienungsanleitung

30 August 2024

Apantac HDBT-1-R Bedienungsanleitung

30 August 2024

Apantac DP-FIB Bedienungsanleitung

30 August 2024

Apantac EDID-EW-H Bedienungsanleitung

30 August 2024

Apantac HDM2.0-FIB-II-SM Bedienungsanleitung

30 August 2024

Apantac HDBT-SET-1 Bedienungsanleitung

29 August 2024

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-

DAS Audio AX-112-5 Bedienungsanleitung

16 Oktober 2024

Ferplast Ergocomfort Freetime Bedienungsanleitung

16 Oktober 2024

AEG MECK52 Bedienungsanleitung

16 Oktober 2024

Makita UR012G Bedienungsanleitung

16 Oktober 2024

Stihl HT 70 Bedienungsanleitung

16 Oktober 2024

Ernesto H14270 Bedienungsanleitung

16 Oktober 2024

IFM AC901S Bedienungsanleitung

16 Oktober 2024

Nedis RFPOM120FBK Bedienungsanleitung

16 Oktober 2024

AEG E9KLCS01 Bedienungsanleitung

16 Oktober 2024

ART ProChannel II Bedienungsanleitung

16 Oktober 2024