Antec NSK1480 Bedienungsanleitung

Antec Computergehäuse NSK1480

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Antec NSK1480 (7 Seiten) in der Kategorie Computergehäuse. Dieser Bedienungsanleitung war für 17 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/7

New Solution Series

NSK 1480

User’s Manual

Manuel de l’utilisateur

Anwenderhandbuch

Manuale per l’operatore

Manual del usuario

পᡅ䂀ᯢ᳌

At Antec, we continually refine and improve our products to ensure the highest

quality. As such, your new case may differ slightly from the description in this

manual. This isn’t a problem; it’s simply an improvement. As of the date of publication,

all features, descriptions, and illustrations in this manual are correct.

New Solution Series User’s Manual

NSK 1480

Quiet Desktop Slim Case

The Power Supply

The NSK 1480 comes with a 350-Watt power supply (PSU) that features universal

input and active PFC. This includes dual 12V output rails that deliver safer and

more reliable output to the system’s components. This PSU has achieved 80 PLUS®

Certification, the latest independent standard in power supply efficiency. It reduces

power consumption by up to 25%, saving you money on your electricity bill. In

addition it has a variety of industrial-grade protective circuitry: OPP (over power

protection), OVP (over voltage protection), UVP (under voltage protection), and

SCP (short circuit protection).

The Rubber Pads/Stands

There are four rubber pads inside the tool bag. If you want to place the case

horizontally on a desktop, stick the rubber pads to the bottom of the case. There

are also two stands so the case can stand up vertically. Place the case onto the

stands with the optical drive bay at its top position. Make sure the stands do not

block the two air intakes on the bottom.

Setting Up

1. Place the case upright on a flat, stable surface.

2. Remove the thumbscrews from the back of the top panel. Slide the panel

towards the rear to remove it from the case.

3. Inside the case you should see the power supply, some wiring with marked

connectors (USB, PWR etc.), and installed I/O panel and a power cord.

The Dual Chamber structure

Upon opening the top panel, you will find that the case is divided into two separate

chambers—the motherboard chamber and the HDD chamber. The power supply is

designed to directly suck fresh air from outside the case. This unique feature combined

with the dual chamber structure isolates heat and noise from each section, resulting in

much quieter and cooler operation than a traditional desktop case. Although care

has been taken to prevent sharp edges in your Antec case, we strongly recommend

taking the appropriate time and care when working with it. Avoid excessive force

and hurried or careless motions. Please take reasonable precautions.

Disclaimer

This manual is intended only as a guide for Antec’s Computer Enclosures. For more

comprehensive instructions on installing the motherboard and peripherals, please

refer to the user’s manuals that come with those components.

Installing the Motherboard

This manual is not designed to cover CPU, RAM, or expansion card installation.

Please consult the motherboard manual for specific mounting instructions and

troubleshooting.

The motherboard is located inside the main chamber with two 80 mm TriCool TM

fans preinstalled right next to the CPU.

1. Lay the case down, with the open side facing up. The drive cages and power

supply should be visible.

2. Make sure you have the appropriate I/O panel for the motherboard. If the

panel provided is not suitable for the motherboard, please contact the

motherboard manufacturer for the correct I/O panel.

3. Remove the cross bar on the motherboard chamber.

4. Line up the motherboard with the mounting holes. There are three special

brass standoffs pre-installed on the motherboard tray. Two of them are

threaded and one is an unthreaded post. Make note of any that don’t line

up with a corresponding hole in the motherboard. Not all motherboards will

match with all of the provided screw holes, and this is not necessary for

proper functionality.

5. Remove the motherboard by lifting it up.

6. Remove any of the pre-installed standoffs that aren’t needed.

7. Place the motherboard back on the standoffs. Attach the motherboard to the

threaded brass standoffs with the special nuts that comes with your tool bag.

Note: You do not need to fasten the unthreaded brass standoff.

8. Fasten the rest of the standoffs with the provided Philips-head screws. The

motherboard is now installed.

Connecting the Power and LED

If the motherboard has a 20-pin power receptacle, detach the 4-pin attachment

on the 24-pin power connector. Before you connect the power supply to any of

the devices, please consult the appropriate user manuals for the motherboard and

other peripherals.

1. Connect the 24-pin Main Power Connector and the

4-pin connector to the motherboard as needed. If the

motherboard uses a 20-pin connector; detach the

4-pin attachment on the 24-pin power connector

(see pictures 1 and 2).

Note: the detachable 4-pin section cannot be used in

place of a 4-pin +12V connector.

2. Connect the Reset switch (labeled RESET SW) to the motherboard at the RST

connector. Polarity (positive and negative) does not matter for switches.

3. The Power Switch (labeled POWER SW) connects to the PWR connector on

the motherboard.

4. The Power LED (labeled POWER LED) connector is located behind the Reset

connector. For LEDs, colored wires are positive (+). White or black wires are

negative (–). If the LED does not light up when the system is powered on, try

reversing the connection. For more info on connecting LEDs to your motherboard,

see your motherboard manual.

5. The Hard Drive LED (labeled HDD LED) connects to the hard drive activity header.

Picture 1 Picture 2

For 24-pin

motherboards

For 20-pin

motherboards

Produktspezifikationen

Marke:	Antec
Kategorie:	Computergehäuse
Modell:	NSK1480
Breite:	390 mm
Tiefe:	410 mm
Höhe:	120 mm
Anzahl USB 2.0 Anschlüsse:	2
Typ:	PC
Stromversorgung:	350 W
Formfaktor:	Desktop
Audioanschlüsse:	Ja
Audioausgang:	Ja
Erweiterungssteckplätze:	4
externe Laufwerkseinschübe:	1 x 5.25”
interne Laufwerkseinschübe:	2 x 3.5”
Ventilator:	3 x 80mm
Mainboard Größe:	9.6 x 9.6 "