Antec Mini P180 Bedienungsanleitung

Antec Computergehäuse Mini P180

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Antec Mini P180 (8 Seiten) in der Kategorie Computergehäuse. Dieser Bedienungsanleitung war für 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/8

Mini P180 / Mini P180 White

User’s Manual

Manuel de l’utilisateur

Anwenderhandbuch

Manuale per l’operatore

Manual del usuario

পᡅ䂀ᯢ᳌

Ё᭛Փ⫼᠟ݞ

At Antec, we continually refine and improve our products to ensure the highest

quality. As such your new case may differ slightly from the descriptions in this

manual. This isn’t a problem; it’s simply an improvement. As of the date of publication,

all features, descriptions, and illustrations in this manual are correct.

Mini P180 / Mini P180 White User’s Manual

The Mini P180 is a small case that’s big on features. It is a professional case that

is highly configurable. For that reason, this case comes without a power supply.

Make sure you choose a power supply that conforms to the newest ATX standard

and is compatible with your motherboard.

Most ATX power supplies come with an on/off switch. Make sure you turn the

switch to the ON (I) position before you boot up your computer for the first time.

Normally, you won’t need to switch to the OFF (O) position, since the power supply

includes a soft on/off feature. This lets you turn your computer on and off by using

the soft switch on your computer case. If your computer crashes and you can’t

shut it down using the soft switch, you can switch the main power to the OFF (O)

position to clear the fault, then reboot.

Setting Up

1. Place the case upright on a flat, stable surface with the rear of the case facing you.

2. Remove the thumbscrews from the right side panel. Grip the panel at the top

and bottom and slide it towards you to open the case.

3. Remove the screws from the left side panel. Grip the panel at the top and

bottom and slide it towards you to remove the left side panel.

Note: Don’t use your fingernails to pry or lift the panels.

Inside the case you should see two separate chambers — the upper chamber

for motherboard, a 5.25” external drive and up to 5 hard drives; and the lower

chamber for power supply and two bays for 5.25” external drives. The upper

5.25” bay will accommodate a CD or DVD drive up to 170mm in length. You

will also find some wiring with marked connectors (USB, PWR etc.), drive

rails for 5.25” drives, installed I/O panel, and a 5.25” to 3.5” drive bay adapter.

Remove the middle hard disk cage to access the tool box which contains all

the hardware screws, spare silicone grommets, and standoffs.

Installing the power supply

1. With the case upright, install the power supply into the case.

Note: You can mount the power supply either side up. If you have a power

supply with a large fan, the fan should be on top once the unit is installed.

2. Between the two chambers a plastic structure lets you run cables between

the upper and lower chambers.

Disclaimer

This manual is intended only as a guide for Antec’s Computer Enclosures. For more

comprehensive instructions on installing the motherboard and peripherals, please

refer to the user’s manuals that come with those components.

Installing the Motherboard

This manual does not cover CPU, RAM, or expansion card installation. Please consult

your motherboard manual for specific mounting instructions and troubleshooting.

1. Lay the case down, with the open side facing up. The drive cages and power

supply area should be visible.

2. Make sure you have the correct I/O panel for your motherboard. If the panel

provided with the case isn’t suitable, please contact your motherboard

manufacturer for the correct I/O panel.

3. Line up the motherboard with the standoff holes. Determine which holes line

up and remember where they are. Not all motherboards will match with all of

the provided screw holes, and this is not necessary for proper functionality.

Some standoffs may be pre-installed for your convenience.

4. Remove your motherboard by lifting it up.

5. Install standoffs as needed and put the motherboard back in.

6. Screw in your motherboard to the standoffs with the provided Philips-head

screws. Your motherboard is now installed.

Cable Organizer

Instead of running all the power cables into the upper chamber, they can be organized

between the motherboard and right side panel.

1. Remove both side panels.

2. Choose the cables you would like to pass through the holes behind

the motherboard tray and pull them out of the power supply chamber towards

the right side of the case.

3. Route them up through the gap in the bar and use the cable ties to hold them

in place.

4. Feed the cables back through the insertion point nearest the destination of

the cable. Connect the cable and then pull the slack back to the right side of

the case.

5. When finished, secure all cables with ties and put the right panel back in place.

Connecting the Ports and LEDs

1. Connect the Reset switch (labeled RESET SW) to your motherboard at the

RST connector. Polarity (positive and negative) does not matter for switches.

2. Power Switch (labeled POWER SW) connects to the PWR connector on

the motherboard.

3. Power LED (labeled POWER LED) connects to the PWR header on

the motherboard. For LEDs, colored wires are positive (+). White or black

wires are negative (–). If the LED does not light up when the system is powered

on, try reversing the connection. For more info on connecting LEDs to your

motherboard, see your motherboard manual.

4. Hard Drive LED (labeled HDD LED) connects to the hard drive activity header.

Connecting the USB Ports

You will find a single 10-pin connector on a cable attached to the front USB ports.

This Intel standard connector is keyed so that it can’t be accidentally reversed, as

long as it is connected to a proper Intel standard motherboard header. Connect the

10-pin connector to your motherboard headers so that the blocked pin fits over the

missing header pin.

Produktspezifikationen

Marke:	Antec
Kategorie:	Computergehäuse
Modell:	Mini P180
Breite:	212 mm
Tiefe:	436 mm
Gewicht:	9500 g
Produktfarbe:	Weiß
Höhe:	435 mm
Anzahl USB 2.0 Anschlüsse:	2
Verpackungsbreite:	283 mm
Verpackungstiefe:	515 mm
Verpackungshöhe:	510 mm
Paketgewicht:	11100 g
Zertifizierung:	RoHS, AQ3
Typ:	PC
Formfaktor:	Mini Tower
Audioanschlüsse:	Ja
Anzahl eSATA-Anschlüsse:	1
Audioausgang:	Ja
Gewicht (imperial):	20.9 Pfund
Erweiterungssteckplätze:	4
externe Laufwerkseinschübe:	3 x 5.25"; 1 x 3.5"
interne Laufwerkseinschübe:	5 x 3.5"
Ventilator:	1 rear 120mm x 25mm, 1 top 200mm x 25mm
Optionale Lüfter:	2 front chamber 120mm