Antari SW-250 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Antari SW-250 (31 Seiten) in der Kategorie Schneefräse. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/31
SW-250/SW-250X
Wireless Control
High Output Snow Machine
User Manual
English Français Deutsch • • • 中文
© 2018 Antari Lighting and Eects Ltd.
4
UNPACKING & INSPECTION
Open the shipping carton and check that all equipment necessary to operate the machine arrived intact. have
The shipping carton should contain the followin items: g
1. Snow machine with power cable
2. W-1 wireless transmitter (Only for SW-250 model)
3. Fluid tank
4. Hanging bracket
5. Screw set and user manual
Before beginning initial setup of your ANTARI - /SW- Snow Machine, make sure that there is no SW 250 250X
evident damage caused by transportation. In the event of a damaged cable or unit housing, do not plug it in
nor use it until contacting your Antari dealer for assistance.
SETUP and POWER ON
1 move all packing materials from shipping box. Check that all foam and plastic paddings are removed. . Re
2. Place the machine on a at surface and follow the steps below.
Tank cap
Tank
Filter
PU Liquid Tube
Adaptor
with Nut
A ssem blin g Tank & Filter
Please note that "adaptor with nut"
set must be tightly connected.
3. Assemble the hanging bracket on the machine, use the M8 screws to position the hanging bracket
with the machine, the tightening screws are for adjusting the machine’s angle when in the air.
Assembling Hanging Bracket
Assemble 4 washers on both inner sides of the hanging
bracket w ith M8 screw s on outer sides as indicated.
Hanging Bracket
M8 Screw
Tightening
Scr ew
Washer
4. Fill with ANTARI SL-5(A) s uid. Any other types of fluid can damage the unit. When lled, place cap now
back on liquid tank.
5
5. Plug the power cable into a grounded electrical outlet and ip the power switch at the rear of the machine
for powering on.
TRANSMITTER REGISTRATION
ONLY FOR SW-250 MODEL
After powering on, the LCD screen will show sequentially Antari SW- and then Wireless Setup . Press “250” “ …”
button A on the transmitter(s) to register when “ ” “Wireless Setup visible. There is a total of 15 seconds to …” is
nish the registration of the transmitter(s). Once registration is completed, the LCD screen will blink and beep.
The LCD screen will nally show Wireless Setup once the 15 seconds ends. Up to 5 transmitters are “OK”
allowed to be registered with one SW- The included transmitter has been registered with the machine 250.
before shipment and can be directly operated without any start-up setting. Therefore, the registration is only
needed before use of new W- 1.
Note: All transmitter(s) registration must be completed within 15 seconds or SW-250 has to be power on
again for next registration.
LCD CONTROL OPERATION
After transmitter(s) registration time ends, LCD screen will then show To Snow Now the machine is “Ready ”.
ready for operating.
FUNCTIONS SETTING
Press for setting dierent functions per sequence as below. Menu button
Interval Set Up/Timer Set the interval time under timer mode by pressing and
Down/Volume buttons (20 to 2000 seconds).
Duration Set Up/Timer Set the duration time under timer mode by pressing and
Down/Volume buttons (10 to 200 seconds).
Timer Out Up/TimerSet the output volume under timer mode by pressing and


Produktspezifikationen

Marke: Antari
Kategorie: Schneefräse
Modell: SW-250

Brauchst du Hilfe?

Wenn Sie Hilfe mit Antari SW-250 benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Schneefräse Antari

Bedienungsanleitung Schneefräse

Neueste Bedienungsanleitung fĂźr -Kategorien-