AMX CB-MXP10 Bedienungsanleitung
AMX
Flat panel steun
CB-MXP10
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für AMX CB-MXP10 (2 Seiten) in der Kategorie Flat panel steun. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/2
Installation Guide
CB-MXP10 Rough-In Box and Cover Plate for Modero X 10” Panel
Overview
The CB-MXP10 Rough-In Box (FG039-17) is an optional accessory for the Modero X
Series 10” Wall Mount Touch Panel. It allows the panel to be mounted directly to the
studs/pre-wall.
The back of the Modero X Series 10” Wall Mount Touch Panel is contained within a
plastic outer housing or back box, and the back box attaches to the Rough-In Box. The
Rough-In Box kit includes a wall box, cover, and mounting screws.
Specifications
WARNING: In order to guarantee a stable installation of the touch panel, the distance
between the CB-MXP10 and the outer wall surface must be a minimum of .50 inches
(1.27cm) and a maximum of .1.50 inches (3.81cm).
• Refer to the 95-5968-34 diagram for detailed installation dimensions.
Pre-Wall Installation of the CB-MXP10 Rough-In Box
1. Remove the rough-in box cover (B in FIG. 1) before installation of the Rough-In
Box (A). Note: the cover MUST be removed before drywall installation. The
cover may be reinstalled after drywall installation using 4-40 screws (not
included).
2. Fasten the CB-MXP10 rough-in box to the stud through the holes on the Stud
Mounting tabs, using either nails or screws (not provided).
3. Additional framing or blocking may be desired for a more robust mounting.
4. Remove the appropriate wiring knockouts from the rough-in box to
accommodate the cables being threaded through to the 19” or 20” Wall Mount
Touch Panel.
5. Thread the incoming Ethernet and USB wiring through the knockouts. Using the
left wiring knockouts for USB connector cables and the right wiring knockouts for
the LAN/PoE In cable is very highly recommended with this installation. Leave
enough slack in the wiring to accommodate installation of the docking station.
6. Install the drywall/sheetrock before inserting the back box for the CB-MXP10.
7. Cut out the opening for the Wall Mount Touch Panel back box where the wall has
been placed over the Rough-In Box. Cutting out the surface slightly smaller than
what is outlined in the installation drawings, so that you can make any necessary
cutout adjustments, is very highly recommended.
NOTE: The front cover of the CB-MXP10 (B in FIG. 1) should be installed after the
appropriate wiring is pulled to the Rough-In Box. The cover should then be removed
prior to the installation of the touch panel back box and discarded.
FIG. 1 CB-MXP10 Rough-In Box - with front cover
8.65”
(21.98 cm)
A
B
8.94”
(22.71 cm)
5.78”
(14.68 cm)
Rough-In Box
Rough-In Box With Cover
Cover
CB-MXP10 (FG039-17) Specifications
Dimensions (HWD) • Rough-In Box: 8 5/8" x 9 7/8" x 2 1/4" (22.0 cm x 22.7 cm x
5.7 cm)
• Rough-In Box Cover Plate: TBD
Weight • With cover: TBD
• Without cover: 1.80 lbs (0.82 kg)
Certifications • UL Listed
Included
Accessories: • Cover Plate for Rough-in Box (FG039-20)
• Back Box to Rough-In Box Mounting Screws (4)
( )80-5967-03
• Cover Plate to Rough-In Box Mounting Screws (4)
( )80-5967-03
Recommended
Wall Cutout
for the CB-MXP10
5.5”
(13.97 cm)
8.75”
(22.23 cm)
For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).
4/12
©2012 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
AMX reserves the right to alter specifications without notice at any time.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com
93-0039-17 REV: B
Cover
CB-MXP10
Rough-In Box
Without Cover
CB-MXP10
Rough-In Box
With Cover
(oblique angle)
Knock-outs
Front
(oblique angle)
Cover screws
2.24”
(5.68 cm)
8.94”
(22.71 cm)
2.24”
(5.68 cm)
5.78”
(14.68 cm)
2.39”
(6.08 cm)
6.48”
(16.6 cm)
2.39”
(6.08 cm)
8.94”
(22.71 cm)
Front
Produktspezifikationen
| Marke: | AMX |
| Kategorie: | Flat panel steun |
| Modell: | CB-MXP10 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit AMX CB-MXP10 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Flat panel steun AMX
27 August 2024
27 August 2024
27 August 2024
27 August 2024
Bedienungsanleitung Flat panel steun
- Flat panel steun Samsung
- Flat panel steun Da-Lite
- Flat panel steun HP
- Flat panel steun Kensington
- Flat panel steun Manhattan
- Flat panel steun Schwaiger
- Flat panel steun König
- Flat panel steun Atlantic
- Flat panel steun Luxor
- Flat panel steun Hitachi
- Flat panel steun Icy Box
- Flat panel steun Cabstone
- Flat panel steun Techly
- Flat panel steun Vogel's
- Flat panel steun SilverStone
- Flat panel steun Vision
- Flat panel steun InFocus
- Flat panel steun NEC
- Flat panel steun Marantz
- Flat panel steun Monoprice
- Flat panel steun Fellowes
- Flat panel steun Iiyama
- Flat panel steun Kogan
- Flat panel steun Acco
- Flat panel steun HQ
- Flat panel steun Sanus
- Flat panel steun B-Tech
- Flat panel steun Barkan
- Flat panel steun Ergotron
- Flat panel steun NewStar
- Flat panel steun Speaka
- Flat panel steun Digitus
- Flat panel steun Reflecta
- Flat panel steun BlueBuilt
- Flat panel steun Peerless-AV
- Flat panel steun Ematic
- Flat panel steun GPX
- Flat panel steun Peerless
- Flat panel steun Steren
- Flat panel steun Ultimate
- Flat panel steun BakkerElkhuizen
- Flat panel steun Chief
- Flat panel steun Siig
- Flat panel steun StarTech.com
- Flat panel steun APart
- Flat panel steun Planar
- Flat panel steun Proaim
- Flat panel steun Konig & Meyer
- Flat panel steun Atdec
- Flat panel steun Premier Mounts
- Flat panel steun Gabor
- Flat panel steun V7
- Flat panel steun Rocstor
- Flat panel steun Avteq
- Flat panel steun Zaor
- Flat panel steun CTA Digital
- Flat panel steun Bell'O
- Flat panel steun Anthro
- Flat panel steun Mount-It!
- Flat panel steun My Wall
- Flat panel steun SmartMetals
- Flat panel steun Multibrackets
- Flat panel steun Walker Edison
- Flat panel steun LTN Technologies
- Flat panel steun Heckler
- Flat panel steun Helder
Neueste Bedienungsanleitung für -Kategorien-
17 September 2024
15 September 2024
15 September 2024
15 September 2024
12 September 2024
10 September 2024
9 September 2024
8 September 2024
6 September 2024
6 September 2024