Alpine KWE-403ID6 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Alpine KWE-403ID6 (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
1
Connectivity Layout
8
Steering wheel remote control
interface installation kit for
IVECO
Model: Daily VI open dash with SWRC
Year: 2014 > 2019
Kit content: SWRC interface
wiring harness
All installation work must be performed by a qualified professional installer only.
The manufacturer / dealer is not liable for any kind of incidental or indirect damages.
06/2020 ALL RIGHTS RESERVED. Technical changes possible. No liability for misprints.
2
6
5
7
8
9
10
11
3
4
1
2
Content and wiring harness connections
INSTALL THIS HARNESS INSTEAD THE POWER CABLEOF
CONTAINED THE X D-ID, KIT-7 AND KIT-F9 KITSIN 903 ID ID
FOLLOWING THE PROCEDURES BELOW:
REMOVE THE INTERFACE WITH THE LABEL SHOWN BELOW
FROM THE KITS: X D-ID, KIT-7 AND KIT-F9 :903 ID ID
AND CONNECT IT TO POINT (4) SEE THE NEXT PAGE.
3
1 - to RADIO connector
2 - to RADIO connector
3 - to CAMERA INPUT
4 - to X903D-ID / KIT-7ID / KIT-F9ID interface
5 - to LIN BUS connector cable:
to key harness contained in X903D-ID,
to LIN cable contained in KIT-7ID & KIT-F9ID
6 - AUX input
7 - connect these 3 cables to the 3 voltage SWRC cable in the vehicle:
Pink with Pink cable
Pink/Black with Pink/Black cable
Brown with Brown cable
8 - to SERVICES provided by the vehicle:
Yellow - to vehicle SPEED pulse (MUST be connected to vehicle)
White - to vehicle REVERSE signal (MUST be connected to vehicle)
9 - CAMERA control / REMOTE output
10 - POWER ANTENNA output
11 - to CAR connector
12 - external power access
12
Connect the two SERVICES cables.
→Yellow - to vehicle SPEED pulse (MUST be connected to vehicle)
→White - to vehicle REVERSE signal (MUST be connected to vehicle)
4
Body Computer/Fuse Box
Left Connector F (Green or Black):
Pin 4 = Reverse Light
Remove the cover of the Green or Black plug. The Grey/Green or
White/Green cable carries the reverse signal. Remove the terminal from
the connector housing. Connect the White cable (point 8 / page 3) from
the wiring harness to the Grey/Green or White/Green cable from the
vehicle connector.
5
Body Computer/Fuse Box
Right Connector D (Black):
Pin 56 = Speed Signal
Remove the cover of the Black plug.
The Orange cable, if proven otherwise, installing a PIN, carries the speed
signal. Remove the terminal from the connector housing.
Connect the White cable (point 8 / page 3) from the wiring harness to
the Grey/Green or White/Green cable from the vehicle connector.
Connect the harness as indicated in the installation manual
(IM_X903D-ID_EN) of X903D-ID (page 26-27) to vehicle and as
indicated on the last page (8). Please also note the points on the
following pages of these instructions.
1. Cable Connections 2.1 Connecting Reverse Signal (White cable (point 8 / page3))
2. Speed and Reverse Cable Connections (point 8 / page 3)
2.2 Connecting Speed Signal (Yellow cable (point 8 / page3))


Produktspezifikationen

Marke: Alpine
Kategorie: Nicht kategorisiert
Modell: KWE-403ID6

Brauchst du Hilfe?

Wenn Sie Hilfe mit Alpine KWE-403ID6 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Alpine

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-