AKG PZM-10 Bedienungsanleitung

AKG Mikrofon PZM-10

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für AKG PZM-10 (2 Seiten) in der Kategorie Mikrofon. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
T
PZM 10 (LL)
he A K G / C r o w n PZM10 is a Pressure
Zone Microphone
® desi ed for gn
se
cu
rity, surveillance, and conference-
table use.
PRESSUREZONE
MICROPHONE
Si e it nc does not l k oo like a microphone, it is
inconspicuous. The mic’s t lar housi ubu ng
mounts in a 25/32" diameter hole in a ceiling
panel, wall or table.
Like other Pressure Zone Microphones, the
PZ
M1
0 es a miniature mic capsulus e
mounted very near a sound-reflecting plate or
boundary, in the Pressure Zone. In this zone,
d
ir
ect sound from the sound source combines
in ase at all eph fr quencies with reflected
sound o the boundary. The benets are
ma
ny
: 6 dB more sensitivity, 6 dB less noise, a
wide smooth efr quency response ee ofr f
phase interference, excellent clarity and
“
r ,each
” and consistent pickup anywhere
around the mic.
In the M10, low ePZ fr quencies below the
vo
ice ra
nge are rolled o to reduce pickup of
air conditi ing rumble. The hi - eon gh fr quency
response is boosted slightly to help articula-
ti
on
.
Be
cause of its tailored response and PZM
constr , the 0 wuc onti PZM1 ill pick up conver-
sa
ti
on
s or other desired sounds with extra
clarity and definition.
The microphone connector is an XLR t e yp
(3-pin pro audio) for easy pl -in i taug ns llation.
The
ou put
t is balanced, low i edamp nce, which
a
ll
ow
s long cable r s wun ithout hum pickup or
hi - egh fr quency loss. Powering is by 12 to
48 V phantom power.
The PZM10 LL has a line level output.
The mic’s humbucking transformer and steel
case prevent hum pickup, even near fluores-
cent lights.
Installation
To pick up speech at a small conference table
(about 6 f t square), mount e 0 iee on PZM1 n
the mi le of the table. For longer tables, dd use
on
e
PZ
M in the middle of every 4 to 6 people.
No person should be more than 3 f t om ee fr
the nearest microphone.
1. Pl se refer to Fig. 2 and identify the paea rts
shown.
2.
De
termine ere u want to iwh yo nstall the
microphone, and drill a 25/32" diameter hole
Specifications
T
ra
nsducer type:
Electret condenser.
F
re
qu
ency response (typical): 80 Hz to ,000 20
Hz. See Fig. 1.
Polar pattern: Hemispherical.
I edance: mp 240 ohms, balanced. Recom-
me
nd
ed mini m load i edamu mp nce 1000
ohms.
Open circuit sensitivity:
2.5 mV/Pa* (–52 dB V/ ). Pa
Power sensitivity: –52 dBm/Pa*
E
qu
ivalent noise level (self- ise): no
26 dB SPL t ical (0 dB = 0.0002 dyne/cmyp 2),
A-wei ted. gh
S/N Ratio: 68 dB at 94 dB SPL.
Ma
xi m SPL: mu
120 dB SPL produces 3% THD.
Operating vol ge: ta 12 to 48 V phantom power,
pos
iti
ve voltage on pins 2 and 3 with respect
to pin 1.
Po
l ity: ar
Positive pressure on the diaphragm
pr es a itive age on pin 2 woduc pos volt ith
re
sp
ect to pin 3 of ou put t connector .
Cu
rre
nt drain: 400 microamperes.
Output connectors:
PZM10: Ma le XLR t e (3-pin pr ayp o udio).
PZM10 LL: Line level output,
unterminated cable.
Cable: None supplied. Use 2-conductor shielded
mic cable.
Materials: St l plate and housi . ee ng
Fini : sh Off- e. May be painted any whit color; take
care to rst seal the ening betwop een the
capsule and boundary plate.
Net wei t: gh 2.6 oz. ( .6 g). 73
Dimensi s: on See Fig.2.
Fig. 1
Fig. 2
F
re
quency Response
F
re
quency in Hz
there. * 1 pascal = 10 dynes/cm2 = 10 microbars = 94 dB SPL.
0
®
3. Obtain some 2-conductor ielded mish c
cable, l g enough to run om your eon fr quip-
ment input to the microphone. If space is ti t gh
behind the mounting rface, tain a t- su ob righ
a
ng
le female XLR connector. Solder the fe-
male XLR connector to the cable: on shield to
pin 1, hot l d to pin 2, other l d to pin 3. ea ea
4. Run the female XLR and mic cable to the
hole.
5.
Using a 5/ " A32
llen wrench, remove the
co
ll
ar
from the microphone. I ert the micro- ns
phone tube into the hole.
6.
S
lide the collar to the mic t e. Pull thon ub e
plate tight agai t the ns hole and press the collar
ti
gh
t agai t the mounns ting rface. Ti tesu gh n
the Allen screw in the collar.
7. Plug your mic cable into the microphone.
8. Plug the other end of your mic cable into
one of these devices:
* A mic pr mp that suppea lies phantom power.
* A mixer that supplies phantom power.
* A
ph
antom power supply, such as the A K G /
C r o w n PH4B or PH1A.
Connect the out t of the supply to the mipu c
i t of your mic pr , mixer or renpu eamp corder.
Ar
ch
i ctste
’ and Engineers’ Specifications
The microphone shall be the A K G / C r o w n
PZ
M10 or e
quivalent. The microphone shall
be a electret condenser Pressure Zone
Microphone with a hemispherical polar
pa
tt
ern. The microphone shall have a tubular
housing whi mounts in a ch 25/32" diameter
ho
le. Open-cir
cuit sensitivity shall be 2.5
mV/Pa typical. Equivalent noise level shall be
26 dBA t ical. Maxi m yp mu SPL shall be
120 dB for 3% THD. Powering shall be 12-48
V
ph
antom power. Out connector put shall be
male XLR-t e. yp
The A K G / C r o w n PZM10 microphone is
specied.
Warranty
A K G / C r o w n professi al microphones are on
guarant d unconditiee onally agai t ns
ma
lf
unc
tion from any cause for a period of
three years from dat of oe riginal pur ase. ch
Pl se refer to the eea nc osl ed full warranty
statement for more detail.
Service
If the unit fails to work, first replace or repair
the mic cables and check the power supply. If
you determine that the microphone
product is defective, return the
complete product in its original
packaging to one of the addresses
below. For further assistance or
technical support call the international
helpdesk at +43 676 83200 888.
PZM10 Schematic
AKG ACOUSTICS GMBH LAXENBURGER STRASSE 254, 1230 VIENNA/AUSTRIA
AKG ACOUSTICS, U.S. SERVICE 24950 GROVE VIEW ROAD, MORENO VALLEY, CA 92551, U.S.A
© 2015 HARMAN International Industries, Incorporated. All rights reserved. AKG is a trademark of AKG Acoustics GmbH, registered in the United States
and/or other countries.
Features, specications and appearance are subject to change without notice.
www.akg.com
PZM10 (LL)

Produktspezifikationen

Marke: AKG
Kategorie: Mikrofon
Modell: PZM-10

Brauchst du Hilfe?

Wenn Sie Hilfe mit AKG PZM-10 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Mikrofon AKG

AKG

AKG WMS420 Bedienungsanleitung

13 Oktober 2024
AKG

AKG CBL201B Bedienungsanleitung

8 Oktober 2024
AKG

AKG D5 CS Bedienungsanleitung

29 September 2024
AKG

AKG C3000 Bedienungsanleitung

22 September 2024
AKG

AKG H85 Bedienungsanleitung

14 September 2024
AKG

AKG D5 C Bedienungsanleitung

10 September 2024
AKG

AKG P3S Bedienungsanleitung

9 September 2024
AKG

AKG GN15 M Bedienungsanleitung

6 September 2024
AKG

AKG CBL99 Bedienungsanleitung

4 September 2024
AKG

AKG Sound Grabber II Bedienungsanleitung

4 September 2024

Bedienungsanleitung Mikrofon

Neueste Bedienungsanleitung für -Kategorien-

Power Dynamics

Power Dynamics PD524 Bedienungsanleitung

15 Oktober 2024
Sennheiser

Sennheiser ew 100 G4-845-S Bedienungsanleitung

13 Oktober 2024
Audio-Technica

Audio-Technica BP892xCH Bedienungsanleitung

12 Oktober 2024
Sennheiser

Sennheiser SKM 300-835 G3-G Bedienungsanleitung

9 Oktober 2024
Sennheiser

Sennheiser SKM 500 G4 Bedienungsanleitung

9 Oktober 2024
Audio-Technica

Audio-Technica ATM610a Bedienungsanleitung

8 Oktober 2024
Omnitronic

Omnitronic AAB-10 Bedienungsanleitung

8 Oktober 2024
Audio-Technica

Audio-Technica BP894x Bedienungsanleitung

7 Oktober 2024
Azden

Azden SGM-250CX Bedienungsanleitung

6 Oktober 2024
Audio-Technica

Audio-Technica XM1S Bedienungsanleitung

5 Oktober 2024