ZyXEL SFP10G-SR Bedienungsanleitung

ZyXEL Schalten SFP10G-SR

Lesen Sie kostenlos die šŸ“– deutsche Bedienungsanleitung fĆ¼r ZyXEL SFP10G-SR (1 Seiten) in der Kategorie Schalten. Dieser Bedienungsanleitung war fĆ¼r 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/1
SFP and SFP+ Transceivers
Userā€™s Guide
1
2
EN
Removing Fiber-optic Cable
1
Attach an ESD preventive wrist strap to your
wrist and to a bare metal surface on the chassis.
Disconnect all ļ¬ber-optic cables from the
SFP/SFP+ module.
1
2
EN
Installing a Module 1
Attach an ESD preventive wrist strap to your
wrist and to a bare metal surface.
Remove the a module from its protective
packaging.
Locate the transmit (Tx) and the receive (Rx)
markings on the module.
Align the module in front of the slot opening on a
device.
Insert the module into the slot until the module
snaps into place
Note : Module installation orientation varies
depending on your device. Your module comes
with a mechanism that prevents incorrect
insertion. Do NOT force or twist the module into a
slot. Do NOT insert an SFP+ module into a
1-Gigabit SFP slot.
1
2
3
4
5
EN
Connecting a Fiber-optic Cable 2
Remove the dust plugs from a module and the
cables.
Identify the signal transmission direction of the
ļ¬ber-optic cable and the module. Insert one end
of the ļ¬ber-optic cable into the module.
Insert the other end of the ļ¬ber-optic cable into a
remote device.
Note : Refer to the userā€™s guide that comes with
your device for module slot status.
1
2
3
EN
Introduction
Copyright Ā© 2019 Zyxel Communications Corp. All Rights Reserved.
EU Importer
Zyxel Communications A/S
Gladsaxevej 378, 2. th. 2860 SĆøborg, Denmark
http://www.zyxel.dk
US Importer
Zyxel Communications, Inc
1130 North Miller Street Anaheim, CA 92806-2001
http://www.us.zyxel.com
Removing a Module
3
Unlocking a Module
2
Insert the dust plug into the ports on a module.
Pull out the latch and down to unlock a module.
Using your thumb and index ļ¬nger, grasp the
tabs on both sides of the module and carefully
slide it out of the slot.
Note : Do NOT force or twist the module out of a
slot.
1
EN
Use a transceiver module for connection to a remote device. SFP
and SFP+ transceiver modules are hot swappable. You can install
and remove a module while your device is operating.
SFP/SFP+ modules both use 3.3V power input and LC-type
connectors.
SFP/SFP+ modules support data rate of 100M/1G/10G bps and
single-mode/multi-mode connection based on its speciļ¬cation.
Handling Warning
All modules are static sensitive. To prevent damage from
electrostatic discharge (ESD), it is recommended you attach an ESD
preventive wrist strap to your wrist and to a bare metal surface
when you install or remove a module.
All modules are dust sensitive. When not in use, always keep the
dust plug on. Avoid getting dust and other contaminant into the
optical bores, as the optics do not work correctly when obstructed
with dust.
Safety Warning
All modules are equipped with a Class 1 laser, which emits invisible
radiation. Read the following safety warnings carefully.
ā€¢To avoid possible eye injury, do not look into an operating
ļ¬ber-optic moduleā€™s connectors.
ā€¢Laser radiation is present when the device or system is powered
up.
ā€¢Only trained and qualiļ¬ed personnel should be allowed to install or
replace these modules.
Environmental Warnings
ā€¢Dispose of your ļ¬ber-optic module according to all national laws
and regulations.
...warranty must be validated with the seller's ....
See the Zyxel website for a list of supported transceivers.


Produktspezifikationen

Marke: ZyXEL
Kategorie: Schalten
Modell: SFP10G-SR

Brauchst du Hilfe?

Wenn Sie Hilfe mit ZyXEL SFP10G-SR benƶtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Schalten ZyXEL

Bedienungsanleitung Schalten

Neueste Bedienungsanleitung fĆ¼r -Kategorien-