WyreStorm EX-100-H2-PRO Bedienungsanleitung

WyreStorm Audio-/Video-Extender EX-100-H2-PRO

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für WyreStorm EX-100-H2-PRO (4 Seiten) in der Kategorie Audio-/Video-Extender. Dieser Bedienungsanleitung war für 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

4K HDR 4:4:4 60Hz HDBaseT™ Extender with DSC

Supporting USB.2.0 Client/host (4K: 100m/328ft)

EX-100-H2-PRO Quickstart Guide

EX-100-H2-PRO v1 Quickstart Guide | 190829

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

1 of 4

WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the

installation process.

Basic Wiring Diagram

HDMI

HDBaseT

Cat6/6a

Ethernet

EX-100-H2-PRO Transmitter (TX)

EX-100-H2-PRO Receiver (RX)

Personal Computer

Wireless Access Point

Isochronous

USB 2.0 Data

USB 2.0 Host

USB

Flash Drive

Short Throw

Projector

Hearing

Induction Loop

12 DC 2A

Power Supply

12 DC 2A

Power Supply

HDMI

Analog Audio

RS-232

Interactive Whiteboard

RS-232 from Control System

KEY

Wireless Router

IMPORTANT! Installation Requirements

• Visit the product page to download the latest rmware, document

versions, additional documentation, and conguration tools.

• Read through the section for important wiring Wiring and Connections

guidelines before creating or choosing premade cables.

• While this product supports CEC, WyreStorm cannot guarantee

compatibility with all forms of CEC communication.

In the Box

1x EX-100-H2-PRO Transmitter (TX)

1x EX-100-H2-PRO Receiver (RX)

1x IR Emitter

1x IR Receiver

2x 3-pin Terminal Block

1x 12V DC 3A Power Supply (US/UK/EU/AU)

4x Mounting Brackets

1x Quickstart Guide (this document)

EX-100-H2-PRO v1 Quickstart Guide | 190829

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

2 of 4

Wiring and Connections

WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in it’s

entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.

IMPORTANT! Wiring Guidelines

• The use of patch panels, wall plates, cable extenders, kinks in cables, and

electrical or environmental interference will have an adverse effect on

signal transmission which may limit performance. Steps should be taken

to minimize or remove these factors completely during installation for best

results.

• WyreStorm recommends the use of shielded category cable to minimize

signal noise and interference.

• WyreStorm recommends using pre-terminated HDMI cables due to the

complexity of these connector types. Using pre-terminated cables will

ensure that these connections are accurate and will not interfere with the

performance of the product.

IR TX/RX Guidelines

• Using WyreStorm infrared emitters and receivers is the best way to ensure

that most IR coding formats are transmitted and received Other 3rd party

emitters and receivers can be used; however, these devices must operate in

the same manner as the WyreStorm devices.

• Due to differences in IR across 3rd party control systems their IR ports

should never be connected directly to a WyreStorm system as an

incompatibility may exist. WyreStorm offers a cable that compensates for

voltage differences as well adjusts for differences in the pins used within the

port. Refer to the product page for more information.CAB-IR-LINK

IR TX Port Pinout

Connection for IR TX (transmit) uses a 3.5mm (1/8in) mono plug.

Tip: Anode

Sleeve: Cathode (IR Signal)

IR RX Port Pinout

Connection for IR RX (receive) uses a 3.5mm (1/8in) stereo jack that outputs

+5V DC to power the included IR receiver.

Tip:

Ring: IR Signal

+5V DC

Sleeve: Ground (GND)

Audio Connections

Tip:

Ring:

Left Channel

Right Channel

Sleeve: Ground (GND)

RS-232 Wiring

The EX-100-H2-PRO uses a 3-pin RS-232 with no hardware ow control. Most

control systems and computers are DTE where pin 2 is RX, this can vary from

device to device. Refer to the documentation for the connected device for pin

functionally to ensure that the correct connections can be made.

Refer to for details on setting RS-232 modes.RS-232 Mode Settings

3rd Party Device

Pin 1 TX (Transmit) > To > RX (Receive)--- ---

Pin 2 RX (Receive) > To > TX (Transmit--- ---

Pin 3 G (Gro d) > To > G (Gro d)un --- --- un

WyreStorm Co ectornn

EX-100-H2-PRO v1 Quickstart Guide | 190829

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

3 of 4

Setup and Conguration

USB Operation

When using the USB ports one of the units needs to set as a host while the

other is set as a device connection. The host can be either the TX or RX as long

as the other unit is set to device.

Set the switch to to connect to a host device Host

such as a PC or Mac. Requires that the opposite unit

is set to Device.

Set the switch to to connect devices such Device

keyboards or USB cameras to the unit. Requires that

the opposite unit is set to Host.

RS-232 Port Conguration

The RS-232 port on this extender has 2 settings that are important to the

operation of the unit. While being used the RS-232 switch should be in the

Pass-through position. Set the switch to for normal RS-232 Pass Through

operation. This is the default setting.

Set the switch to Update when updating rmware.

Troubleshooting

No or Poor Quality Picture (snow or noisy image)

• Verify that power is being supplied to the transmitter and receiver.

• Verify that the HDBaseT cable is properly terminated following EIA568B

standard.

• Verify that the output resolution of the source and display is supported by

this extender.

• If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.

• Verify that all source and HDBaseT connections are not loose and are

functioning properly

No or Intermittent 3rd party Device Control

• Verify that the IR, RS-232, and Ethernet cables are properly terminated

following the section.Wiring and Connections

• Verify that RS-232 modes are properly selected for the desired operation.

Refer to for details.RS-232 Mode Settings

Troubleshooting Tips:

• WyreStorm recommends using a cable tester or connecting the cable to

other devices to verify functionality.

Produktspezifikationen

Marke:	WyreStorm
Kategorie:	Audio-/Video-Extender
Modell:	EX-100-H2-PRO
Breite:	195 mm
Tiefe:	94.8 mm
Gewicht:	360 g
Produktfarbe:	Schwarz
Übertragungstechnik:	Kabelgebunden
Höhe:	21 mm
Gleichstrom-Anschluss (DC):	Ja
Betriebstemperatur:	0 - 45 °C
Relative Luftfeuchtigkeit in Betrieb:	10 - 90 %
Typ:	AV-Sender & -Empfänger
Stromverbrauch (max.):	8.88 W
Stromstärke:	3 A
Temperaturbereich bei Lagerung:	-20 - 70 °C
Luftfeuchtigkeit bei Lagerung:	10 - 90 %
HDCP:	Ja
Rack-Einbau:	Ja
USB-Stecker:	USB Type-A, USB Type-B
Anzahl der USB-Anschlüsse:	10
USB-Version:	2.0
Maximale Bildwiederholrate:	60 Hz
Externes Netzteil:	Ja
Maximale Auflösung:	3840 x 2160 Pixel
HDMI-Version:	2.0
Nachhaltigkeitszertifikate:	RoHS
Anzahl der HDMI-Ausgänge:	1
Arbeitsspannung:	12 V
Bandbreite:	10.2 Gbit/s
HDMI-In:	1
HDCP-Version:	2.2
3,5 mm (1/8-inch) in:	Ja
RS-232 Eingangs-Ports:	2
Fernbedienung (IR) input:	2
RJ-45-Eingangsanschlüsse:	1
HDBaseT-Port:	Ja
RJ-45-Ausgangsanschlüsse:	1
3,5 mm (1/8-inch) out:	Ja
Erweiterte Display-Identifikationsdaten (EDID):	Ja
HDCP-Durchschleifung:	Ja
HDBaseT zertifiziert:	Ja
Ethernet/LAN:	Ja