Waring Commercial 7015N Bedienungsanleitung
Waring Commercial
Blender
7015N
Lesen Sie kostenlos die đ deutsche Bedienungsanleitung fĂźr Waring Commercial 7015N (2 Seiten) in der Kategorie Blender. Dieser Bedienungsanleitung war fĂźr 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/2
Blender
Operating anual M
IMPORTANT
HOT BLENDING INSTRUCTIONS
To minimize the possibility of scalding when blending hot materials, the
following precautions and procedures must be observed:
1) If you are using the standard two-piece container lid that originally
came with your blender, limit the amount of material processed to
.1/2 pint
NOTE: A special accessory lid assembly is available for use with
, which allows safe processing ofstainless steel containers only
larger loads.
Order 1-Quart Hot Blending Lid, Catalog No. CAC14.
2) If you are using the standard two-piece container lid, completely
remove the center portion of the lid before turning blender on.This
will allow venting of the rapidly heated and expanding air present
inside container when blender is running.
If you are using the , follow the instructions special accessory lid
packed with the lid; venting will be accomplished automatically.
3) Always start blending on lowest speed setting, then progress to
desire speed.
4) Never stand directly over blender when it is being started or while
running.
SERVICE
Refer to the list of Factory Approved Service Centers enclosed with
your Waring Blender for the name of the nearest Service Center or
Write to:
SERVICE CENTER
314 ELLA T. GRASSO AVENUE
TORRINGTON, CT 06790
(800) 269-6640
Ship Blenders for repair to the above address or to a Factory Approved
Service Center. Do not ship to a Waring Sales OfďŹce.
Replacement parts for your own âOut of Warrantyâ repairs are obtainable
at the above address.
WARING COMMERCIAL
314 Ella T. Grasso Ave.
P.O.Box 3201
Torrington, CT 06790
www.waringproducts.com 014775 RV05 0306
IMPORTANT SAFEGUARDS
When using electrical equipment basic safety precautions should
always be followed including the following:
1. READ ALL INSTRUCTIONS.
2. To protect against electrical hazards do not immerse the Blender
Base in water or other liquid.
3. Close supervision is necessary when any blender is used by or near
children.
4. Unplug from outlet when not in use, before putting on or taking off
parts, and before cleaning.
5. Avoid contacting moving parts.
6. Do not operate your blender with a damaged cord or plug or after the
appliance malfunctions or is dropped or damaged in any manner.
Return appliance to the nearest authorized service facility for
examination, repair or electrical or mechanical adjustment.
7. The use of attachments including canning jars not recommended by
the blender manufacturer may cause a risk of personal injury.
8. Do not use outdoors.
9. Do not let cord hang over edge of table or counter, or touch hot
surfaces.
10. Keep hands and utensils out of container while blending to prevent
the possibility of severe personal injury and/or damage to the
blender. A rubber scraper may be used but must be used only when
the blender is not running.
11. Blades are sharp. Handle carefully.
12. If your blender utilizes a removable Jar Base and Blade Assembly,
to avoid injury never place cutter assembly cutting blades on base
without container properly attached.
13. Always operate blender with cover in place.
14. When blending hot liquids, remove center piece of two-piece cover
on those units supplied with this construction. See Hot Blending
Instructions.
SAVE THESE INSTRUCTIONS
PRESET TIMER BLENDER
SPECIFICATIONS
⢠RATING 3.5A at 120VAC/50HZ (CATALOG NO. 7015)
1.5A at 230VAC/50HZ (CATALOG NO. 8015)
⢠AUTOMATIC Two preset timing intervals (15 seconds and 3 seconds) selectable via
TIMER toggle switch on control panel. Timer can be bypassed for manual
operation
⢠BASE Die cast zinc and steel, baked enamel and chrome ďŹnish top.
⢠CONTAINER 48 ounce capacity Lexan polycarbonate jar with stainless steel blade,
two-piece plastic cover.
⢠CORD 6 foot, 18 gauge, three conductor grounded cord with strain relief.
⢠U.L. LISTED 120V models only.
CONTROL PANEL COMPONENTS
⢠MODE SELECTOR SWITCH Three position maintained contact toggle switch
located on right hand side of control panel, labeled AUTO/OFF/MANUAL;
selects desired operating mode.
⢠TIMING SELECTOR SWITCH Three position momentary contact toggle switch,
spring loaded to center position, located on left hand side of control panel,
labeled 15 SEC/3 SEC; selects desired timing interval.
⢠INDICATOR LAMP Neon pilot light; indicates when mode selector switch is in
either AUTO or MANUAL position.
OPERATION INSTRUCTIONS
1. Be sure mode selector switch is in the OFF (center) position.
2. Plug power cord into properly wired and grounded outlet.
3. For AUTOMATIC operation:
⢠Set mode selector switch to AUTO position. Indicator lamp will light.
⢠Momentarily move timing selector switch to position for time cycle desired.
Motor will run for interval selected, and stop automatically.
NOTE: Override of the automatic stop can be obtained by holding the timing selector
switch in position beyond the end of the preset interval. Motor will continue to run
until switch is released.
⢠When ďŹnished blending, return mode selector switch to OFF position. Indicator lamp
will extinguish.
4. For MANUAL operation:
⢠Set mode selector switch to MANUAL position. Indicator lamp will light, and motor
will run continuously.
⢠When ďŹnished blending, return mode selector switch to OFF position. Motor will stop
and indicator lamp will extinguish.
5. Unplug power cord from outlet when blender is not in use, before putting on or taking
off any parts other than container, and before cleaning.
Produktspezifikationen
Marke: | Waring Commercial |
Kategorie: | Blender |
Modell: | 7015N |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Waring Commercial 7015N benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Blender Waring Commercial
5 September 2024
5 September 2024
28 August 2024
24 August 2024
24 August 2024
24 August 2024
24 August 2024
15 August 2024
12 August 2024
12 August 2024
Bedienungsanleitung Blender
- Blender Sinbo
- Blender Clatronic
- Blender Domo
- Blender Emerio
- Blender G3 Ferrari
- Blender Tristar
- Blender Medion
- Blender Nedis
- Blender Philips
- Blender SilverCrest
- Blender Hanseatic
- Blender Sunbeam
- Blender Panasonic
- Blender Quigg
- Blender Adler
- Blender Beper
- Blender Bestron
- Blender Camry
- Blender Princess
- Blender Trisa
- Blender Bosch
- Blender AEG
- Blender Ambiano
- Blender Ardes
- Blender Siemens
- Blender Bifinett
- Blender Caso
- Blender Concept
- Blender Electrolux
- Blender Fagor
- Blender Gorenje
- Blender Jata
- Blender Klarstein
- Blender Proficook
- Blender Rommelsbacher
- Blender Severin
- Blender Solis
- Blender Springlane
- Blender Unold
- Blender Gastroback
- Blender H.Koenig
- Blender Hendi
- Blender Melissa
- Blender Russell Hobbs
- Blender Steba
- Blender Studio
- Blender Taurus
- Blender Tefal
- Blender Vox
- Blender Day
- Blender ECG
- Blender Mesko
- Blender Telefunken
- Blender Black And Decker
- Blender Amica
- Blender BEKO
- Blender Blaupunkt
- Blender Blokker
- Blender Boretti
- Blender Bourgini
- Blender Brabantia
- Blender Braun
- Blender Cuisinart
- Blender Eldom
- Blender Eta
- Blender Fritel
- Blender Graef
- Blender Grundig
- Blender Heinner
- Blender Hotpoint
- Blender Inventum
- Blender Kenwood
- Blender Kitchen Crew
- Blender KitchenAid
- Blender Koenig
- Blender Krups
- Blender Maestro
- Blender Moulinex
- Blender Sage
- Blender Sharp
- Blender Solac
- Blender Trebs
- Blender Vitamix
- Blender Wilfa
- Blender Witt
- Blender WMF
- Blender Brandt
- Blender GE
- Blender Bartscher
- Blender Nordmende
- Blender Svan
- Blender King
- Blender Philco
- Blender Continental Edison
- Blender Hitachi
- Blender JTC
- Blender Orava
- Blender Magimix
- Blender Livoo
- Blender DCG
- Blender Dualit
- Blender LĂźmme
- Blender Morphy Richards
- Blender Ritter
- Blender Sencor
- Blender Maxwell
- Blender Ariete
- Blender Efbe-Schott
- Blender Kalorik
- Blender Optimum
- Blender Rotel
- Blender Saro
- Blender Scarlett
- Blender Ufesa
- Blender Costway
- Blender Cecotec
- Blender Zephir
- Blender Elba
- Blender MPM
- Blender Thomas
- Blender Imetec
- Blender Logik
- Blender G21
- Blender Novis
- Blender Wolf
- Blender OBH Nordica
- Blender Omega
- Blender Profilo
- Blender Zelmer
- Blender Bamix
- Blender Breville
- Blender George Foreman
- Blender Esperanza
- Blender Kogan
- Blender Innoliving
- Blender Eufy
- Blender Vitek
- Blender Sogo
- Blender Gourmetmaxx
- Blender Ninja
- Blender Bellini
- Blender Noveen
- Blender Swan
- Blender AYA
- Blender Hamilton Beach
- Blender Orbegozo
- Blender Izzy
- Blender Saturn
- Blender Baby Brezza
- Blender Duronic
- Blender Dynamic
- Blender Espressions
- Blender Homeland
- Blender Kambrook
- Blender Magic Bullet
- Blender NutriBullet
- Blender Oster
- Blender Santos
- Blender Thane
- Blender Grunkel
- Blender Tower
- Blender Tribest
- Blender Turbotronic
- Blender Weasy
- Blender Xsquo
- Blender Blendtec
- Blender Beautiful
- Blender WestBend
- Blender Bella
- Blender Nevir
- Blender Girmi
- Blender Chefman
- Blender CRUX
- Blender Globe
- Blender Dash
- Blender Flama
- Blender Focus Electrics
- Blender Robot Coupe
- Blender Riviera & Bar
- Blender AvaMix
- Blender Khind
- Blender Sam Cook
- Blender BioChef
- Blender Semak
- Blender Create
- Blender Brentwood
- Blender Electroline
- Blender Comelec
- Blender Nutri Ninja
- Blender Power Air Fryer XL
- Blender Proappliances
- Blender Imarflex
- Blender Mystery
Neueste Bedienungsanleitung fĂźr -Kategorien-
17 September 2024
16 September 2024
16 September 2024
16 September 2024
16 September 2024
16 September 2024
16 September 2024
15 September 2024
15 September 2024
14 September 2024