Wachendorff LD200600 Bedienungsanleitung

Wachendorff Messgeräte LD200600

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Wachendorff LD200600 (16 Seiten) in der Kategorie Messgeräte. Dieser Bedienungsanleitung war für 20 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/16

AIR PRESSURE STABILIZATION VENT (57.15)

2.25

GENERAL DESCRIPTION

The Large Display is a versatile display that can be congured as a single or

dual counter with rate indication, scaling, serial communications and a dual

relay output. There are also basic models that have a single counter with

direction control only (no scaling or relay output).

The 4 & 6 digit displays are available in either 2.25" or 4" high red LED digits

with adjustable display intensities. The 2.25" high models are readable up to 130

feet. The 4" high models are readable up to 180 feet. All versions are constructed

of a NEMA 4X/IP65 enclosure in light weight aluminum.

The 6-digit programmable models have two signal inputs and a choice of

eight dierent count modes. These include bi-directional, quadrature and anti-

coincidence counting, as well as a dual counter mode. When programmed as a

dual counter, each counter has separate scaling and decimal point selection.

Rate indication is available on the programmable models only. The rate

indicator has separate scaling and decimal point selection, along with

programmable display update times. The meter display can be toggled either

manually or automatically between the count and rate values.

The programmable models also come with a dual Form C relay output and

RS232 or RS485 serial communications. The outputs can activate based on

either counter or rate setpoint values. An internal batch counter can be used to

count setpoint output activations.

SAFETY SUMMARY

All safety regulations, local codes and instructions that appear in this and

corresponding literature, or on equipment, must be observed to ensure personal

safety and to prevent damage to either the instrument or equipment connected to

it. If equipment is used in a manner not specied by the manufacturer, the

protection provided by the equipment may be impaired.

Do not use this unit to directly command motors, valves, or other actuators

not equipped with safeguards. To do so can be potentially harmful to persons or

equipment in the event of a fault to the unit.

The protective conductor terminal is bonded to conductive

parts of the equipment for safety purposes and must be

connected to an external protective earthing system.

SPECIFICATIONS

1. DISPLAY: 2.25" (57 mm) or 4" (101 mm) intensity adjustable Red LED

2. :POWER REQUIREMENTS

AC POWER: 50 to 250 VAC 50/60 Hz, 26 VA

DC POWER: 21.6 to 250 VDC, 11 W

DC OUT: +24 VDC @ 100 mA if input voltage is greater than 50 VAC/VDC

+24 VDC @ 50 mA if input voltage is less than 50 VDC

Isolation: 2300 VRMS for 1 min. to all inputs and outputs

3. :COUNT INPUT(S)

Counter(s) have DIP switch selectable pull-up (7.8 K ) or pull-down 

resistors (3.9 K ) that determine active high or active low input logic.

Counters are DIP switch selectable for high or low frequency (Damping

capacitor provided for switch contact bounce. Limits input frequency to 50

Hz and input pulse widths to 10 msec min.)

Input A Trigger levels: VIL = 1.25 V max; VIH = 2.75 V min; VMAX = 28 VDC

Input B Trigger levels: VIL = 1.0 V max; VIH = 2.4 V min; VMAX = 28 VDC

Overow Indication: Display “ ” alternates with overowed count value.

LD200400, LD200600, LD400400, & LD400600:

Count Rate: 25 KHz max. @ 50% duty cycle (no scaling)

LD2006P0 & LD4006P0:

Maximum Count Rates: 50% duty cycle, count mode dependent.

With setpoints disabled: 25 KHz, all modes except Quadrature p1-x4 (23 KHz).

With setpoint(s) enabled: 20 KHz, all modes except Dual Counter (14

KHz), Quadrature p1-x2 (13 KHz) and Quadrature p1-x4 (12 KHz).

4. RATE INPUT LD2006P0 & LD4006P0 only: Models

Display Range: 0 to 99999

Min Freq.: 0.01 Hz

Max Freq.: See Count Input specication

Accuracy: ±0.01%

Rate Overow Indication: Display “”

 2.25" & 4" HIGH RED LED DIGITS

 AVAILABLE IN 4 OR 6 DIGIT VERSIONS

 SINGLE OR DUAL COUNTER with RATE INDICATOR *

 PROGRAMMABLE SCALING AND DECIMAL POINTS *

 BUILT-IN BATCH COUNTING CAPABILITY *

 PROGRAMMABLE USER INPUT *

 UNIVERSALLY POWERED

 DUAL 5 AMP FORM C RELAY *

 ALUMINUM NEMA 4X CASE CONSTRUCTION

* Programmable models only

MODEL LD - LARGE DISPLAY

DIMENSIONS In inches (mm)

Bulletin No. LD-H

Drawing No. LP0607

Released 10/09

Tel +1 (717) 767-6511

Fax +1 (717) 764-0839

www.redlion.net

PART

NUMBER X (Length) Z (Center)

LD2004xx 12 (304.8) 8 (203.2)4 (101.6)

LD2006xx 16 (406.4)

LD4004xx 20 (508)

LD4006xx 26 (660.4) 22 (558.8)

CAUTION: Risk of Danger.

Read complete instructions prior to

installation and operation of the unit.

CAUTION: Risk of electric shock.

16 (406.4)

12 (304.3)4 (101.6)

Y (Height)

7.875 (200)

US LISTED

51EB

IND. CONT. EQ.

ORDERING INFORMATION

TYPE MODEL NO. DESCRIPTION PART NUMBER

Basic

(No front

panel keys)

2.25" High 4-Digit Red LED Counter LD200400

2.25" High 6-Digit Red LED Counter LD200600

4" High 4-Digit Red LED Counter LD400400

4" High 6-Digit Red LED Counter LD400600

Programmable

(With front

panel keys)

2.25" High 6-Digit Red LED Count/Rate Indicator w/ dual Relay Output &

RS232/RS485 Serial Communications LD2006P0

4" High 6-Digit Red LED Count/Rate Indicator w/ dual Relay Output & RS232/

RS485 Serial Communications LD4006P0

LD Plug Panel Meter Plug for LD models (NOT included in LD Product UL File) LDPLUG00

5. RESET/USER INPUT: Function programmable for LD2006P0 &LD4006P0

Reset/User Input: DIP switch selectable pull-up (7.8 K ) or pull-down 

resistor (3.9 K ) that determines active high or active low input logic.

Trigger levels: VIL = 1.0 V max; VIH = 2.4 V min; VMAX = 28 VDC

Response Time: 10 msec typ.; 50 msec debounce (activation and release)

6. COMMUNICATIONS (LD2006P0 & LD4006P0 only):

RS485 SERIAL COMMUNICATIONS

Type: RS485 multi-point balanced interface (isolated)

Baud Rate: 300 to 38.4 k

Data Format: 7/8 bits; odd, even, or no parity

Bus Address: 0 to 99; max 32 meters per line

RS232 SERIAL COMMUNICATIONS

Type: RS232 half duplex (isolated)

Baud Rate: 300 to 38.4 k

Data Format: 7/8 bits; odd, even, or no parity

7. MEMORY: Nonvolatile E2PROM retains all programming parameters and

count values when power is removed.

8. :OUTPUT (LD2006P0 & LD4006P0 only)

Type: Dual Form C contacts

Contact Rating: 5 amps @ 120/240 VAC or 28 VDC (resistive load), 1/8

H.P. @ 120 VAC (inductive load)

Life Expectancy: 100 K cycles min. at full load rating. External RC snubber

extends relay life for operation with inductive loads.

Response Time: Turn On or Off: 5 msec max.

Isolation to Input & User/Exc Commons: 2000 Vrms for 1 min.

Working Voltage: 240 Vrms

9. ENVIRONMENTAL CONDITIONS:

Operating temperature: 0 to 50 °C

Storage temperature: -40 to 70 °C

Operating and storage humidity: 0 to 85% max. RH (non-condensing)

Vibration According to IEC 68-2-6: Operational 5 to 150 Hz, in X, Y, Z

direction for 1.5 hours, 2 g’s (1g relay).

Shock According to IEC 68-2-27: Operational 30 g’s (10g relay), 11 msec in

3 directions.

Altitude: Up to 2,000 meters

10. :CONNECTIONS

Internal removable terminal blocks are used for power and signal wiring.

Remove end plates with ¼" nut driver. For LD4 versions, all wiring is on right

side of unit. For LD2 versions, power and signal wiring connections are on

the right side and the relays and serial options are on the left side.

Wire Strip Length: 0.4" (10 mm)

Wire Gage: 24-12 AWG copper wire

Torque: 5.3 inch-lbs (0.6 N-m) max.

Cable Diameter: Outside diameter must be 0.181" (4.6 mm) to 0.312" (7.9

mm) to maintain NEMA 4 rating of cord grips.

11. CERTIFICATIONS AND COMPLIANCES:

SAFETY

UL Listed, File # E137808, UL508, CSA C22.2 No. 14-M95

LISTED by Und. Lab. Inc. to U.S. and Canadian safety standards

Type 4X Enclosure rating, UL50

IEC 61010-1, EN 61010-1: Safety requirements for electrical equipment for

measurement, control, and laboratory use, Part 1.

IP65 Enclosure rating, IEC 529

ELECTROMAGNETIC COMPATIBILITY

Emissions and Immunity to EN 61326: Electrical Equipment for Measurement,

Control and Laboratory use.

Notes:

1. Criterion A: Normal operation within specied limits.

2. Criterion B: Temporary loss of performance from which the unit self-

recovers.

12. CONSTRUCTION: Aluminum enclosure, and steel side panels with textured

black polyurethane paint for scratch and corrosion resistance protection. Meets

NEMA 4X/IP65 specications. Installation Category II, Pollution Degree 2.

13. :WEIGHT

LD2004XX: 3.5 lbs (1.59 kg)

LD2006XX: 4.5 lbs (2.04 kg)

LD4004XX: 8 lbs (3.63 kg)

LD4006XX: 10.5 lbs (4.76 kg)

Class A

Class B

EN 55011

Emissions LD2006P0

Emissions LD200400

Emissions:

0.5 cycle

Criterion A

3 V/rms

EN 61000-4-11Voltage dip/interruptions

Criterion AEN 61000-4-6RF conducted interference

1 kV L-L,

Criterion AEN 61000-4-5Surge

1 kV signal

2 kV power

Criterion AEN 61000-4-4Fast transients (burst)

2 kV L&N-E power

10 V/m

Criterion B LD2006P0

Criterion A LD200400EN 61000-4-3Electromagnetic RF elds

8 kV air discharge

4 kV contact discharge

Criterion AEN 61000-4-2Electrostatic discharge

Immunity to Industrial Locations:

1.0 INSTALLING THE METER

INSTALLATION

The meter meets NEMA 4X/IP65 requirements when properly installed.

INSTALLATION ENVIRONMENT

The unit should be installed in a location that does not exceed the operating

temperature. Placing the unit near devices that generate excessive heat should

be avoided. The unit should only be cleaned with a soft cloth and neutral soap

product. Do NOT use solvents.

Continuous exposure to direct sunlight may accelerate the aging process of

the front overlay. Do not use tools of any kind (screwdrivers, pens, pencils, etc.)

to operate the keypad of the unit.

MOUNTING INSTRUCTIONS

This display is designed to

be wall mounted or suspended

from a ceiling truss or other

suitable structure capable

of supporting the LD.

Caution should be exercised

when hanging the display to

provide for the safety of

personnel. If hanging the LD,

run the suspension cables (or

chains) through the mounting

bracket holes. For wall mounting

use #10-32 size bolts.

MOUNTING HOLE (.281")

MUST BE

CONNECTED TO

TERMINAL #3 (TBA)

3.0 WIRING THE METER

2.0 S DIP SETTING THE WITCHES

SETTING THE 8 DIP SWITCHES

To access the switches, remove the right side plate of the meter. A bank of

eight switches is located inside the unit.

Warning: Exposed line voltage exists on the circuit boards.

Remove all power to the meter and load circuits before accessing

inside of the meter.

SWITCH 1 (Input A)

LOGIC: Input A trigger levels VIL = 1.25 V max.; VIH = 2.75 V min.;

VMAX = 28 VDC

MAG: 200 mV peak input sensitivity; 100 mV hysteresis; maximum voltage:

40 V peak (28 Vrms); Must also have SRC switch ON. (Not recommended

with counting applications.)

SWITCH 2 (Input A) {See Note 1}

SNK.: Adds internal 7.8 K pull-up resistor to +12 VDC, IMAX = 2.1 mA.

SRC.: Adds internal 3.9 K pull-down resistor, 7.2 mA max. @ 28 VDC max.

SWITCH 3 (Input A)

HI Frequency: Removes damping capacitor and allows max. frequency.

LO Frequency: Adds a damping capacitor for switch contact bounce. Limits

input frequency to 50 Hz and input pulse widths to 10 msec.

SWITCH 4 (Input B) {See Note 1}

SNK.: Adds internal 7.8 K pull-up resistor to +12 VDC, IMAX = 2.1 mA.

SRC.: Adds internal 3.9 K pull-down resistor, 7.2 mA max. @ 28 VDC max.

SWITCH 5 (Input B)

HI Frequency: Removes damping capacitor and allows max. frequency.

LO Frequency: Adds a damping capacitor for switch contact bounce. Limits

input frequency to 50 Hz and input pulse widths to 10 msec.

SWITCH 6 (RESET/USER INPUT) {See Note 1}

SNK.: Adds internal 7.8 K pull-up resistor to +12VDC, I

MAX = 2.1 mA.

SRC.: Adds internal 3.9 K pull-down resistor, 7.2 mA max. @ 28 VDC max.

SWITCH 7 (POWER UP RESET)

ENABLE: In this position, the counter resets to zero at power up.

DISABLE: In this position, the counter does not reset at power up.

Note: This switch has no function for programmable models. Power-up reset is

selected through a programming parameter.

SWITCH 8 (Input B)

DIRECTION CONTROL: In this position Input B is used to control the

count direction of Input A when Input A is set to Count with Direction

mode (default mode).

INTENSITY ADJUST: In this position Input B is used to adjust the

LED intensity. There are ve distinct LED levels that can be changed by

pulsing Input B. After setting the desired intensity, move switch to

OFF position for Direction Control. Units with keypads can program the

LED intensity level using Programming Menu 3.

Note 1: When the DIP switch is in the SNK position (OFF), the input is

congured as active low. When the switch is in the SRC position (ON), the

input is congured as active high.

8ON

SNK.

HI FREQ.

Reset/User Input SNK.

Pwr Up Reset DISABLE

Input B Direction Control

SRC.

LO FREQ.

SRC.

ENABLE

Intensity Adjust

Factory Setting

SNK.

LOGIC

SRC.

MAG.

Input A

Input B

EMC INSTALLATION GUIDELINES

Although this meter is designed with a high degree of immunity to Electro-

Magnetic Interference (EMI), proper installation and wiring methods must be

followed to ensure compatibility in each application. The type of the electrical

noise, source or coupling method into the meter may be dierent for various

installations. The meter becomes more immune to EMI with fewer I/O

connections. Cable length, routing, and shield termination are very important

and can mean the dierence between a successful or troublesome installation.

Listed below are some EMC guidelines for successful installation in an

industrial environment.

1. The meter should be properly connected to protective earth.

2. Use shielded (screened) cables for all Signal and Control inputs. The shield

(screen) pigtail connection should be made as short as possible. The

connection point for the shield depends somewhat upon the application.

Listed below are the recommended methods of connecting the shield, in order

of their eectiveness.

a. Connect the shield only at the panel where the unit is mounted to earth

ground (protective earth).

b. Connect the shield to earth ground at both ends of the cable, usually when

the noise source frequency is above 1 MHz.

c. Connect the shield to common of the meter and leave the other end of the

shield unconnected and insulated from earth ground.

3. Never run Signal or Control cables in the same conduit or raceway with AC

power lines, conductors feeding motors, solenoids, SCR controls, and

heaters, etc. The cables should be ran in metal conduit that is properly

grounded. This is especially useful in applications where cable runs are long

and portable two-way radios are used in close proximity or if the installation

is near a commercial radio transmitter.

4. Signal or Control cables within an enclosure should be routed as far as possible

from contactors, control relays, transformers, and other noisy components.

5. In extremely high EMI environments, the use of external EMI suppression

devices, such as ferrite suppression cores, is eective. Install them on Signal

and Control cables as close to the unit as possible. Loop the cable through the

core several times or use multiple cores on each cable for additional protection.

Install line filters on the power input cable to the unit to suppress power line

interference. Install them near the power entry point of the enclosure. The

following EMI suppression devices (or equivalent) are recommended:

Ferrite Suppression Cores for signal and control cables:

Fair-Rite # 0443167251 (RLC# FCOR0000)

TDK # ZCAT3035-1330A

Steward # 28B2029-0A0

Line Filters for input power cables:

Schaner # FN610-1/07 (RLC# LFIL0000)

Schaner # FN670-1.8/07

Corcom # 1 VR3

Note: Reference manufacturer's instructions when installing a line lter.

6. Long cable runs are more susceptible to EMI pickup than short cable runs.

Therefore, keep cable runs as short as possible.

7. Switching of inductive loads produces high EMI. Use of snubbers across

inductive loads suppresses EMI.

Snubber: RLC# SNUB0000.

Produktspezifikationen

Marke:	Wachendorff
Kategorie:	Messgeräte
Modell:	LD200600

Brauchst du Hilfe?

Wenn Sie Hilfe mit Wachendorff LD200600 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Messgeräte Wachendorff

Wachendorff LD4006P0 Bedienungsanleitung

4 September 2024

Wachendorff LD2T06P0 Bedienungsanleitung

4 September 2024

Wachendorff LD4T06P0 Bedienungsanleitung

4 September 2024

Wachendorff LD200600 Bedienungsanleitung

4 September 2024

Wachendorff LD2006P0 Bedienungsanleitung

4 September 2024

Wachendorff S401-L Bedienungsanleitung

4 September 2024

Bedienungsanleitung Messgeräte

Neueste Bedienungsanleitung für -Kategorien-

Stamos S-LS-41 Bedienungsanleitung

16 Oktober 2024

Stamos S-LS-58 Bedienungsanleitung

16 Oktober 2024

PCE Instruments LTS-20 Bedienungsanleitung

16 Oktober 2024

PCE Instruments PCE-313A Bedienungsanleitung

16 Oktober 2024

PCE Instruments PCE-320 Bedienungsanleitung

16 Oktober 2024

PCE Instruments PCE-032-LED Bedienungsanleitung

16 Oktober 2024

PCE Instruments FME Bedienungsanleitung

16 Oktober 2024

PCE Instruments PCE-2500N Bedienungsanleitung

16 Oktober 2024

PCE Instruments PCE-2550 Bedienungsanleitung

16 Oktober 2024

PCE Instruments PCE-2600N Bedienungsanleitung

16 Oktober 2024