Vtech Safe & Sound VM343 Bedienungsanleitung

Vtech Babyphone Safe & Sound VM343

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Vtech Safe & Sound VM343 (4 Seiten) in der Kategorie Babyphone. Dieser Bedienungsanleitung war für 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

Congratulations

on purchasing your new VTech product.

Before using this product, please read

Important safety instructions.

This manual has all the feature operations

and troubleshooting necessary to install and

operate your new VTech product. Please

review this manual thoroughly to ensure

proper installation and operation of this

innovative and feature rich VTech product.

For support, shopping, and everything new at

VTech, visit our website at

www.vtechcanada.com.

What’s in the box

Install the battery

The parent unit runs on rechargeable battery

or AC power. To continuously monitor your

baby, make sure you use both battery and

AC power at the same time. With the battery

alone, the parent unit can cordlessly run for a

short time only.

NOTES

Use only the battery supplied with this product.

The operating time for using the rechargeable

battery is short. If you want to monitor your baby

for a long time, we recommend you connect the

parent unit to AC power.

If the parent unit will not be used for a long time,

disconnect and remove the battery to prevent

possible leakage.

Install the battery as shown below.

NOTES

Press down on the large tab of the battery

compartment cover to pull it out.

THIS SIDE UP

NOTES

Make sure the label is facing up THIS SIDE UP

while inserting the battery.

Replace the battery

To replace the battery, press down on the

large tab of the battery compartment cover

and pull it out, then follow the steps above to

install the battery.

•

Connect and charge the

battery

NOTES

Use only the power adapters supplied with this

product.

Make sure the electrical outlets are not controlled

by wall switches.

The power adapters are intended to be correctly

oriented in a vertical or ﬂoor mount position. The

prongs are not designed to hold the plug in place

if they are plugged into a ceiling, under-the-table

or cabinet outlet.

Make sure the parent unit, the baby unit and the

power adapter cords are out of reach of children.

Connect the baby monitor

•

Charge the parent unit battery

When you have connected the parent unit

and installed its battery for the ﬁrst time or

after power outage, the parent unit powers on

automatically. The battery icon indicates the The battery icon indicates the

battery status (see the following table).

NOTES

The parent unit battery is fully charged after

3 hours of continuous charging.

It takes longer to charge the battery when the

parent unit is turned on. To shorten the charging

time, turn the parent unit off while charging.

The standby time varies depending on the

sensitivity level you set, your actual use and the

age of the battery.

Battery

indicators

Battery

status

Action

The battery

icon is off

and

displays.

No battery

is installed

but operates

using AC

power, or the

battery has

been installed

incorrectly.

Install the

parent unit

battery.

Charge

without

interruption

(at least

30 minutes).

The screen

displays

Battery low

at Parent

Unit and .

The light

ﬂashes.

The battery

has very little

charge and

may be used

for only a

short time.

Charge

without

interruption

(about

30 minutes).

The battery

icon

becomes

solid .

The battery is

fully charged.

To keep

the battery

charged,

connect it to

AC power

when not in

use.

•

Before use

NOTE

This baby monitor is intended as an aid. It is not a

substitute for proper adult supervision, and should

not be used as such.

Test your baby monitor

You may test the baby monitor before initial

use, and at regular times thereafter.

CAUTION

For hearing protection, make sure the parent

unit is more than 1 meter (3 feet) away from

the baby unit. If you hear any high-pitched

noise, move the parent unit further until the

noise stops. You can also press on -/VOL

the parent unit to lower or mute the noise.

63℉

> 1m (3ft)

Make sure your baby units and parent unit

are on.

The parent unit displays images from the

baby unit.

Speak towards the baby unit microphone.

You will hear the sound at the parent

unit.

If you have more than one baby unit, press

VIEW on the top of your parent unit. The

screen switches to other baby units. Then,

repeat step 2.

NOTE

When the parent unit displays and then No link

to CAM # (# represents the selected baby unit

number), and the LED light ﬂashes, move LINK

the parent unit closer to the baby unit (observe

the minimum distance of 1 meter/ 3 feet). You

can also check if the baby monitor is connected

to a live power socket and switched on.

TIP

Increase the parent unit speaker volume if you

cannot hear the sounds transmitted from the baby

unit.

•

Positioning the baby monitor

CAUTION

Keep the baby units out of the reach of your baby.

Never place or mount the baby units inside the

baby’s crib or playpen.

NOTE

To avoid interference from other electronic

devices, place your baby monitor far away from

devices such as wireless routers, microwaves, cell

phones and computers.

Place the baby units more than 1 meter

(3 feet) away from your baby.

More than 1 meter

(3 feet)

> 1m (3ft)

Place the parent unit more than 1 meter

(3 feet) away from the baby units.

63 ē

> 1m (3ft)

< 1m (3ft)

CAUTION

The default volume of your parent unit is level 4.

If you experience high-pitched screeching noise

from your baby monitor while positioning:

Make sure your baby units and parent unit are

more than 1 meter (3 feet) apart, OR

Turn down the volume of your parent unit.

Operating range

The operating range of the baby monitor is

up to 300 meters (1,000 feet) outdoors or

50 meters (160 feet) indoors. The actual

operating range may vary depending on

the environmental conditions and other

interferences such as walls, doors and other

obstructions.

•

Overview

Baby unit overview

1Light sensor

2Infrared LEDs

3Camera

4Microphone

5Speaker

6Antenna

7Power jack

8Temperature sensor

9ON/OFF LED light

On when the baby unit is turned on

and is paired to the parent unit.

Flashes when the baby unit is not

being viewed; or when the link to the

parent unit is lost.

•

10 ON/OFF switch

Slide to turn on or off the baby unit.•

11 -/VOL/+

Press to adjust the baby unit speaker

volume. It determines the talkback

volume transmitted from parent unit.

•

12 PAIR

Your baby units and parent unit

provided are already paired.

Press and hold on accessory baby

units ( , purchased separately) VM305

to pair to the parent unit.

•

13 Threaded socket

For wall mount installation use.•

Parent unit overview

1Antenna

2 LED lights

Indicate the different statuses of

the parent unit. For details, refer to

Parent unit lights.

•

3Microphone

4 On/off

Press and hold to power on.

Press and hold again to power off.

•

5TALK

Press and hold to talk to the selected

baby unit in orSINGLE-CAM

PATROL mode.

•

6 Zoom

Press to zoom in or out while viewing

image in orSINGLE-CAM PATROL

mode.

•

While in a menu, press to choose an

item.

While in orSINGLE-CAM PATROL

mode, press and hold to move the

baby unit camera rightward.

While in SPLIT-VIEW mode, press to

move the selection box rightward.

•

8 BACK

While in a menu, press to return to

the main menu or idle screen.

While in orSINGLE-CAM PATROL

mode, press and hold to move the

baby unit camera leftward.

While in SPLIT-VIEW mode, press to

move the selection box leftward.

•

9VIEW / LCD ON/OFF

Press and hold to turn off the parent

unit screen.

Press to view the image of the

next baby unit in orSINGLE-CAM

PATROL mode.

PATROL

Press to turn on or off the PATROL

mode.

SPLIT

Press to turn on or off the

SPLIT-VIEW mode.

•

10 +/VOL

Press to increase the parent unit

speaker volume.

•

11 -/VOL

Press to decrease the parent unit

speaker volume.

•

12 MENU/SELECT

Press to enter the menu.

While in a menu, press to choose an

item, or save a setting.

•

While in a menu, press to scroll up.

While in orSINGLE-CAM PATROL

mode, press and hold to move the

baby unit camera upward.

While in SPLIT-VIEW mode, press to

move the selection box upward.

•

While in a menu, press to scroll down.

While in orSINGLE-CAM PATROL

mode, press and hold to move the

baby unit camera downward.

While in SPLIT-VIEW mode, press to

move the selection box downward.

•

15 Stand

16 Speaker

17 Power jack

Parent unit lights

LINK On when the parent unit is linked to

the baby unit.

Flashes when the link to the baby

unit being viewed in SINGLE-CAM

or PATROL mode is lost; or when

the link to all baby units being

viewed in SPLIT-VIEW mode is lost.

On when the parent unit is

connected to AC power, or the

battery is charging.

Flashes when the parent unit

battery is low and needs charging.

Off when the parent unit is

disconnected from AC power.

TALK On when the parent unit is talking to

the baby unit.

On when the speaker volume of the

parent unit is turned off.

Parent unit display icons

Connection status

displays when strong signal

strength is detected between the

baby unit and the parent unit.

or displays when moderate

or low signal strength is detected

between the baby unit and the

parent unit.

displays when the link between

the baby unit and the parent unit

is lost.

•

Current view status

Displays the number of the baby

unit that is being viewed when in

SINGLE-CAM and PATROL mode.

Displays the number of the

highlighted baby unit when in

SPLIT-VIEW mode.

•

Patrol mode

Displays when the parent unit is in

PATROL mode.

•

Split-view mode

Displays when the parent unit is in

SPLIT-VIEW mode.

•

Night vision

Displays when the baby unit being

viewed has activated the night

vision feature.

•

Zoom

Displays when the baby unit

camera has zoomed in.

•

Temperature alert tone

Displays when the temperature

alert tone is set on.

•

oF or

Real-time temperature

Displays the real-time temperature

detected by the baby unit in

Fahrenheit (oF) or Celcius (oC)

(e.g. 57 oF 14 or oC).

•

Mute alert

Displays when the parent unit

speaker volume is set to off.

Displays when SPLIT-VIEW mode

is turned on.

•

9-level sound indicator

(1 to 3 bars) indicates low

sound level detected by the baby

unit.

(4 to 6 bars) indicates

moderate sound level detected by

the baby unit.

(7 to 9 bars) indicates high

sound level detected by the baby

unit (e.g. baby crying loudly).

•

Speaker volume

Displays the parent unit speaker

volume level while adjusting.

•

Battery status

animates

when the battery is charging.

displays solid when the battery

is fully charged.

displays when the battery is

low and needs charging.

•

AC power without battery

Displays when the parent unit is

connected to AC power without

the battery.

•

Parent unit main menu icons

Language

You can select a language (English,

French or Spanish) to be used in all

screen displays.

Alert Tone

You can set the parent unit to beep

when

the parent unit operates in low

battery condition;

the link between the parent unit

and the baby unit is lost; or

the baby unit detects sounds

while in SPLIT-VIEW mode.

•

Sensitivity

With this feature, you can choose

to hear sounds from the baby unit

all the time, or to hear sounds that

exceed a certain level. You can

use the parent unit to adjust the

microphone sensitivity of your baby

unit. The higher the sensitivity level,

the more sensitive the baby unit is

in detecting sounds for transmitting

to the parent unit.

Temperature

You can turn on the Temperature

alert tone so that the parent

unit beeps whenever the room

temperature detected by the baby

unit falls outside of the desired

temperature range.

Vibration

You can turn on the vibration alert

so that the parent unit vibrates when

it receives Low battery tone, No

link alert Sound alert in split-view ,

or Temperature alert tone after

turning on the respective alert tones.

Sound-activated Screen

Automatically turns on the

parent unit screen when a baby

unit detects a sound after the

screen is turned off. When no

sound is detected, the screen is

automatically off to save power.

LCD

You can change the brightness of

the parent unit screen, or turn on

the to save power.Dim Mode

Rename

You can choose a speciﬁc name

for the baby unit from a pre-deﬁned

name list.

Pair/Unpair

The baby unit and parent unit

provided are already paired. You

can add or replace baby units

( , purchased separately) to VM305

your baby monitor system.

Parent unit display messages

No link to

CAM # *

The selected baby unit is

out of range or is turned

off.

Battery low at

Parent Unit

The battery level of the

parent unit is very low and

needs to be recharged.

Battery empty.

Powering off ...

The battery is empty and

needs to be recharged.

Sound

detected at CAM #

The sound level exceeds

the threshold at CAM # in

SPLIT-VIEW mode.

Temperature

too high at CAM #

Temperature

too low at CAM #

The temperature

detected by the baby unit

is higher/lower than the

desired temperature alert

range.

Powering on... The parent unit is turning

on.

The parent unit is

searching for baby units.

* # represents the selected baby unit number.

Using the baby monitor

Power on or off the baby unit

Slide switch to the left to turn ON/OFF

on the baby unit. The LED light ON/OFF

turns on.

Slide switch to the right to turn ON/OFF

off the baby unit. The LED light ON/OFF

turns off.

Power on or off the parent unit

Press and hold to turn on the parent unit.

The screen turns on.

Press and hold again to turn off the

parent unit. The screen turns off.

Turn on or off the parent unit

screen

You can turn on or off the parent unit screen

without powering off the parent unit. You can

still hear sound from the baby units.

Press and hold on the parent LCD ON/OFF

unit to turn off the screen.

Press any key on the parent unit to turn on

the screen again.

Adjust speaker volume

For parent unit:

Press or on the parent unit at +/VOL -/VOL

any time when viewing images.

NOTE

When the parent unit speaker volume is set to

zero, appears on the screen and the light

turns on.

For baby unit:

The baby unit speaker volume determines the

talkback volume transmitted from your parent

unit.

Press on the baby unit at any time.-/VOL/+

•

Set the language

You can select a language (English, French or

Spanish) to be used in all screen displays.

Press when the parent unit is idle.MENU

Press or to choose , then Language

press .SELECT

Press or to choose , English Français

or , then press to conﬁrm Espa olñSELECT

your selection.

Adjust LCD brightness

You can change the brightness of the parent

unit screen from to . The LCD Level 1 Level 5

brightness is preset to .Level 3

Press when the parent unit is idle.MENU

Press or to choose , then press LCD

SELECT.

Press SELECT again to choose Brightness.

Press or to choose the desired level of

brightness, then press to conﬁrm SELECT

your selection.

Turn on or off the dim mode

The dim mode is preset to on to help you save

the parent unit power. Whenever the parent

unit has been left idle for 10 minutes while the

screen is still on, the screen will be dimmed

automatically to save power.

Press when the parent unit is idle.MENU

Press or to choose , then press LCD

SELECT.

Press or to choose , then Dim Mode

press .SELECT

Press or to choose or , then On Off

press to conﬁrm your selection.SELECT

NOTE

While the screen is dimmed, any keypress or

alert message will trigger the screen to return to

the preset brightness level. After 10 minutes of

idle, it will be dimmed again.

•

Adjust the sound sensitivity of

the baby units

You can choose to hear sounds from the

baby units all the time, or to hear sounds

that exceed a certain level. You can use the

parent unit to adjust the microphone sensitivity

of your baby units from to . Lowest Highest

The higher the sensitivity level, the more

sensitive the baby unit is in detecting sounds

for transmitting to the parent unit. The sound

sensitivity level is preset to .Highest

Sound sensitivity table for reference

Sensitivity

Level

Description

Highest The parent unit speaker is constantly

on, and you will hear all sounds

(including background noises) from

your baby’s room.

High The parent unit speaker turns on for

soft babbling and louder sounds from

your baby. It remains quiet when your

baby sleeps soundly.

Medium The parent unit speaker turns on

for loud babbling and louder sounds

from your baby. It remains quiet when

your baby makes soft sounds.

Low The parent unit speaker turns on for

crying and louder sounds from your

baby. It remains quiet when your

baby makes soft sounds.

Lowest The parent unit speaker turns on for

loud crying or screeching sounds

from your baby. It remains quiet when

your baby makes soft sounds.

Press when the parent unit is idle.MENU

Press or to choose Sensitivity, then

press . SELECT

If you have more than one baby unit,

the system prompts you to choose the

desired baby unit or all baby units, press

or to choose or , ALL CAM CAM #

then press .SELECT

Press or to choose the desired

sensitivity level, then press to SELECT

conﬁrm your selection.

TIP

You can adjust the baby unit placement to

improve the sound detection.

•

Turn on or off the sound

activation

When sound activation is on, as long as no

sound is detected within 50 seconds, the

parent unit screen will turn off automatically to

save power.

When your baby unit detects a sound, the

sound activation triggers the parent unit

screen to turn on automatically. When no

sound is detected within 50 seconds, the

screen will be off again.

Press when the parent unit is idle.MENU

Press or to choose Sound-activated

Screen SELECT, then press .

Press or to choose or , then On Off

press to conﬁrm your selection. SELECT

The screen returns to main menu.

NOTES

Sound activation is available in SINGLE-CAM

and PATROL mode only.

If the sound sensitivity is set to , the Highest

parent unit screen may remain on continuously

even though sound activation is on.

•

User’s manual

(Canada version)

VM343

Safe & Sound®

Pan & Tilt Full Color

Video Monitor

Go to www.vtechcanada.com

for the latest VTech product news.

Monitoring mode

Every time the parent unit is turned on, it

displays a baby unit in mode. SINGLE-CAM

If there are more than one baby units in your

system, you can also monitor your baby in

PATROL SPLIT-VIEW or mode.

SINGLE-CAM The screen displays a

single baby unit in full

screen.

PATROL A single cam view that

transits to a different baby

unit every 10 seconds.

SPLIT-VIEW The screen displays all

baby units (up to four) on

one screen.

In SINGLE-CAM or PATROL mode:

Press to view the next baby unit.VIEW

Press VIEW

Press PATROL PATROL to switch to mode

if you are in mode, and vice SINGLE-CAM

versa.

10s

•

Press SPLIT to enter the SPLIT-VIEW mode.

In SPLIT-VIEW mode:

Press , , or to select a baby unit.

Press or VIEW key to view the selected

baby unit temporarily in SINGLE-CAM

mode. It returns to SPLIT-VIEW mode after

10 seconds.

Press PATROL PATROL to enter mode.

Press to return to the mode SPLIT

( orSINGLE-CAM PATROL) used before

entering SPLIT-VIEW mode.

NOTES

The parent unit is muted while in SPLIT-VIEW

mode.

Pan, tilt, zoom

You can remotely pan and tilt your baby unit

camera or zoom in while viewing images in

SINGLE-CAM PATROL and mode.

Press and hold , , or to move the

baby unit camera upward, downward,

leftward or rightward correspondingly.

Press to zoom in. Press again to zoom

out.

Talk

You can use the TALK function of the parent

unit to comfort your baby in and SINGLE-CAM

PATROL mode.

Press and hold on the parent unit. TALK

The light turns on.TALK

Speak towards the microphone on the

parent unit. Your voice is broadcast to the

baby unit.

Release the key to stop the TALK

broadcast. The light goes off.TALK

•

Set alert tone

Low battery tone

You can set the parent unit to beep when the

parent unit operates in low battery condition.

Press when the parent unit is idle.MENU

Press or to choose Alert Tone, then

press .SELECT

Press again to choose SELECT

Low Battery Tone.

Press or to choose or , then On Off

press to conﬁrm your selection.SELECT

No link alert

You can set the parent unit to beep when the

link between the parent unit and the baby unit

is lost.

Press when the parent unit is idle.MENU

Press or to choose Alert Tone, then

press .SELECT

Press or to choose , then No Link Alert

press .SELECT

Press or to choose or , then On Off

press to conﬁrm your selection. SELECT

Sound alert in split-view

You can turn on the sound alert feature so that,

while in SPLIT-VIEW mode, the parent unit

beeps and displays Sound detected at CAM #

whenever the baby unit detects sounds.

Press when the parent unit is idle.MENU

Press or to choose Alert Tone, then

press to select.SELECT

Press or to choose Sound alert in

split-view, then press .SELECT

Press or to choose or , then On Off

press to conﬁrm your selection.SELECT

NOTE

The sound alert feature is only available in

SPLIT-VIEW mode.

•

Monitor the temperature

Your baby unit monitors the temperature of

your baby’s room with its built-in temperature

sensor. If the detected temperature is outside

of the preset temperature range, the parent

unit will display alert message.

Set temperature range

You can set the desired room temperature

alert range. The minimum temperature can be

set between 52 oF (11 oC 69 ) and oF (20 oC).

The maximum temperature can be set

between 70 oF (21 oC) 86 and oF (30 oC).

Press when the parent unit is idle.MENU

Press or to choose , then Temperature

press .SELECT

Press or to choose orMinimum

Maximum SELECT, then press .

If you have more than one baby unit,

the system prompts you to choose the

desired baby unit or all baby units, press

or to choose or , ALL CAM CAM #

then press .SELECT

Press or to choose the desired

minimum or maximum temperature, then

press to conﬁrm your selection.SELECT

Temperature alert tone

You can turn on the temperature alert tone so

that the parent unit will emit an alert tone if the

detected temperature is out of range.

Press when the parent unit is idle.MENU

Press or to choose , then Temperature

press .SELECT

Press or to choose Alert Tone, then

press .SELECT

If you have more than one baby unit,

the system prompts you to choose the

desired baby unit or all baby units, press

or to choose or , ALL CAM CAM #

then press .SELECT

Press or to choose or , then On Off

press to conﬁrm your selection.SELECT

•

Temperature format

You can choose to display the temperature in

Fahrenheit (oF) or Celcius (oC).

Press when the parent unit is idle.MENU

Press or to choose , then Temperature

press .SELECT

Press or to choose , then press Format

SELECT.

Press or to choose or Fahrenheit

Celsius SELECT, then press to conﬁrm

your selection.

Turn on or off the vibration

You can turn on the vibration feature so that

the parent unit vibrates when it receives any of

Low battery tone No link alert Sound alert , ,

in split-view Temperature alert tone or after

turning on the respective alert tones.

Press when the parent unit is idle.MENU

Press or to choose , then Vibration

press .SELECT

Press or to choose or .On Off

Press to conﬁrm your selection.SELECT

Rename the baby units

You can rename each baby unit. Once the

baby unit is renamed, its new name together

with the baby unit number will appear in the

sub-menu of below options:

Sensitivity• Rename•

Temperature• Pair/Unpair•

Press when the parent unit is idle.MENU

Press or to choose Rename, then press

SELECT.

Press or to choose the desired baby

unit, then press SELECT.

Press or to choose the desired name

for the baby unit, then press to SELECT

conﬁrm your selection.

Night vision

The baby unit has infrared LEDs that allow you

to see your baby clearly at night or in a dark

room. When the baby unit being viewed

detects low light levels, the infrared LEDs are

switched on automatically. The images from

this baby unit is in black and white, and

appears on screen.

NOTES

It is normal if you see a short white glare on your

parent unit screen as the baby unit is adapting to

the dark environment.

When the infrared LEDs are on, the image is in

black and white. This is normal due to external

light sources.

TIP

Depending on the surroundings and other

interfering factors, like lightings, objects, colors

and backgrounds, the display resolution may vary.

Adjust the baby unit’s angle or place the baby unit

at a higher level to prevent glare and blurry display.

Pair new baby unit (VM305)

The baby units and parent unit provided are

already paired. You can add or replace any

baby units ( , purchased separately) VM305

to your video and audio monitor system. You

can pair a maximum of four baby units to your

parent unit.

For more details, refer to the user’s manual

that comes with your new baby unit.VM305

•

General product care

To keep this product working well and looking good,

follow these guidelines:

Avoid putting it near heating appliances and devices

that generate electrical noise (for example, motors or

ﬂuorescent lamps).

DO NOT expose it to direct sunlight or moisture.

Avoid dropping the product or treating it roughly.

Clean with a soft cloth.

DO NOT immerse the parent unit and the baby

unit in water and do not clean them under the tap.

DO NOT use cleaning spray or liquid cleaners.

Make sure the baby unit and parent unit are dry

before you connect them to the mains again.

Storage

When you are not going to use the baby monitor for

some time, remove the rechargeable battery from

the parent unit. Store the parent unit, the baby unit

and the adapters in a cool and dry place.

•

Frequently asked questions

Below are the questions most frequently asked about

the baby monitor. If you cannot ﬁnd the answer to your

question, visit our website at www.vtechcanada.com,

or contact 1 (800) 267-7377 for customer service.

Why does the

baby monitor

not respond

normally?

Try the following (in the order

listed) for common cure:

1. Disconnect the power to the

baby units and the parent unit.

2. Remove the batteries in the

parent unit. Then install the

batteries again.

3. Wait a few seconds before

connecting power back to the

baby units and the parent unit.

4. Turn on the baby units and the

parent unit.

5. Wait for the parent unit to

synchronize with the baby

units. Allow up to one minute for

this to take place.

Why don’t

the power-on

light of the

baby unit and

parent unit

go on when I

switch on the

units?

Perhaps the parent unit is not

connected to the mains. Insert

the appliance plug into the parent

unit and put the adapter in a wall

socket. Then press and hold

to switch on the parent unit and

to establish connection with the

baby unit.

Perhaps the baby unit is not

connected to the mains. Connect

the baby unit to the mains. Then

set the switch to ON/OFF ON

to switch on the baby unit and

to establish connection with the

parent unit.

Why doesn’t

my parent unit

charge while

connected to

AC power?

Make sure the power is not

controlled by a wall switch.

Make sure the battery is correctly

installed in your parent unit.

You may have used the battery

for a long time. Replace a new

battery.

Why is my

screen in

black and

white?

The screen is in black and white

during nighttime or in a dark

room. This is normal due to

external light sources.

Why do I get

glare or blurry

display on my

screen when

viewing my

baby at night?

During nighttime or in a dark

room, the surroundings and other

interfering factors, like lightings,

objects, colors and backgrounds

may affect the image quality on

your parent unit screen. Adjust

the baby unit’s angle or place

the baby unit at a higher level to

prevent glare and blurry display.

Why does the

baby monitor

produce a

high-pitched

noise?

The parent unit and baby units

may be too close to each other.

Move the parent unit away

from the baby units until the

noise stops; OR

Turn down the volume of your

parent unit.

•

The ON/OFF

light on the

baby unit

ﬂashes and

the parent unit

displays .

The baby unit is unpaired from

the parent unit. Follow below

steps to pair the baby unit. Make

sure both parent unit and baby

unit are on before pairing.

Press when the parent MENU

unit is idle.

Press or to choose

Pair/Unpair CAM, then press

SELECT.

Press again to SELECT

choose .Pair CAM

Press or to choose an

empty baby unit slot, then

press . The parent SELECT

unit screen displays Press

and hold the pair button

at the CAM for 5 seconds

until the power indicator

flashes..

Immediately press and hold

PAIR on the bottom of the

baby unit. The LED light

ﬂashes quickly.

When pairing is successful, the

screen displays the view of newly

paired baby unit in SINGLE-CAM

mode. The LED light on the new

baby unit remains on.

If pairing fails, the screen

displays . Try the Pairing failed

pairing process again.

Only one baby unit can be

paired at a time.

•

Why does the

parent unit

beep?

The baby units may be out of

range. Move the parent unit

closer to the baby units (but not

less than 3 feet).

If the parent unit is powered

by the provided battery, it may

not have enough charge for the

parent unit to perform normally.

Charge the battery in the parent

unit for up to 3 hours.

If your parent unit is in

SPLIT-VIEW mode, some of your

baby units may detect sounds.

The temperature of your baby’s

room may be too high or too low.

Why does the

parent unit

beep/vibrate

frequently in

SPLIT-VIEW

mode?

You may have set the sound

sensitivity level to when Highest

the sound alert (and vibration)

feature are turned on. The parent

unit notiﬁes you of all sounds

including background noise with

beeps (or vibrations). Adjust the

sound sensitivity to a lower level.

Why does

the parent

unit react too

quickly to

other sounds?

The baby unit also picks up other

sounds than those of your baby.

Adjust the sensitivity level to a

lower level or lower the parent

unit speaker volume.

Why don’t I

hear a sound/

Why can’t I

hear my baby

cry?

The parent unit speaker volume

may be too low or off. Press

+/VOL to increase the volume.

You may have set a low sound

sensitivity level. See Adjust the

sound sensitivity of the baby

unit to set to a higher level.

Why can’t I

establish a

connection?

Why is the

connection

lost every now

and then?

Why are

there sound

interruptions?

The baby units may be out of

range. Move the parent unit

closer to the baby units

(observe the minimum distance

of 1 meter/ 3 feet).

Other electronic products may

cause interference with your baby

monitor. Try installing your baby

monitor as far away from these

electronic devices as possible.

Important safety

instructions

When using your equipment, basic safety precautions

should always be followed to reduce the risk of ﬁre,

electric shock and injury, including the following:

Follow all warnings and instructions marked on

the product.

Adult setup is required.

This product is intended as an aid. It is not

a substitute for responsible and proper adult

supervision and should not be used as such.

This product is not intended for use as a medical

monitor.

Do not use this product near water. For example,

do not use it next to a bath tub, wash bowl,

kitchen sink, laundry tub or swimming pool, or in

a wet basement or shower.

CAUTION: Use only the batteries indicated in

this manual. There may be a risk of explosion

if a wrong type of battery is used for the parent

unit. Use only the supplied rechargeable battery

or replacement battery pack (BT198555/

BT298555) for the parent unit. Do not dispose of

batteries in a ﬁre. They may explode. Dispose of

used battery according to the information in The

RBRC® seal.

Use only the adapters included with this product.

Incorrect adapter polarity or voltage can

seriously damage the product.

Baby unit power adapter: Output: 5.9V DC 1A

Parent unit power adapter: Output: 5V DC 1A.

For pluggable equipment, the socket-outlet shall

be installed near the equipment and shall be

easily accessible.

The power adapters are intended to be correctly

oriented in a vertical or ﬂoor mount position. The

prongs are not designed to hold the plug in place

if it is plugged into a ceiling, under-the-table or

cabinet outlet.

Unplug this product from the wall outlet before

cleaning. Do not use liquid or aerosol cleaners.

Use a damp cloth for cleaning.

Unplug the power cords before replacing batteries.

Do not cut off the power adapters to replace

them with other plugs, as this causes a

hazardous situation.

Do not allow anything to rest on the power cords.

Do not install this product where the cords may

be walked on or crimped.

10.

11.

12.

This product should be operated only from the

type of power source indicated on the marking

label. If you are not sure of the type of power

supply in your home, consult your dealer or local

power company.

Do not overload wall outlets or use an extension

cord.

Do not place this product on an unstable table,

shelf, stand or other unstable surfaces.

This product should not be placed in any area

where proper ventilation is not provided. Slots

and openings in the back or bottom of this

product are provided for ventilation. To protect

them from overheating, these openings must

not be blocked by placing the product on a soft

surface such as a bed, sofa or rug. This product

should never be placed near or over a radiator or

heat register.

Never push objects of any kind into this product

through the slots because they may touch

dangerous voltage points or create a short circuit.

Never spill liquid of any kind on the product.

To reduce the risk of electric shock, do not

disassemble this product, but take it to an

authorized service facility. Opening or removing

parts of the product other than speciﬁed

access doors may expose you to dangerous

voltages or other risks. Incorrect reassembling

can cause electric shock when the product is

subsequently used.

You should test the sound reception every

time you turn on the units or move one of the

components.

Periodically examine all components for damage.

Be aware of possible loss of privacy while using

public airwaves. Conversations may be picked

up by other nursery monitors, cordless phones,

scanners, etc.

Children should be supervised to ensure that

they do not play with the product.

The product is not intended for use by persons

(including children) with reduced physical,

sensory or mental capabilities, or lack of

experience and knowledge, unless they have

been given supervision or instruction concerning

use of the appliance by a person responsible for

their safety.

SAVE THESE INSTRUCTIONS

13.

14.

15.

16.

17.

18.

19.

20.

21.

22.

23.

Cautions

Use and store the product at a temperature

between 32oF and 104oF.

Do not expose the product to extreme cold, heat

or direct sunlight. Do not put the product close to

a heating source.

Batteries should not be exposed to excessive

heat such as bright sunshine or ﬁre.

Make sure the baby unit(s) and the adapter

cord(s) are always out of reach of the baby, at

least 3 feet away from the baby or crib, to avoid a

possible strangulation hazard.

Never place the baby unit(s) inside the baby’s crib

or playpen. Never cover the baby unit(s) or parent

unit with anything such as a towel or a blanket.

Other electronic products may cause

interference with your baby monitor. Try

installing your baby monitor as far away

from these electronic devices as possible:

wireless routers, radios, cellular telephones,

intercoms, room monitors, televisions,

personal computers, kitchen appliances and

cordless telephones.

Precautions for users of implanted cardiac

pacemakers

Cardiac pacemakers (applies only to digital cordless

devices):

Wireless Technology Research, LLC (WTR), an

independent research entity, led a multidisciplinary

evaluation of the interference between portable

wireless devices and implanted cardiac

pacemakers. Supported by the U.S. Food and Drug

Administration, WTR recommends to physicians that:

Pacemaker patients

Should keep wireless devices at least six inches

from the pacemaker.

Should NOT place wireless devices directly over

the pacemaker, such as in a breast pocket, when

it is turned ON.

WTR’s evaluation did not identify any risk to

bystanders with pacemakers from other persons

using wireless devices.

Electromagnetic fields (EMF)

This VTech product complies with all standards

regarding electromagnetic ﬁelds (EMF). If handled

properly and according to the instructions in this

user’s manual, the product is safe to be used based

on scientiﬁc evidence available today.

•

The RBRC® seal

The RBRC® seal on the lithium-ion battery indicates

that VTech Communications, Inc. is voluntarily

participating in an industry program to collect and

recycle these batteries at the end of their useful

lives, when taken out of service within the United

States and Canada.

The RBRC® program provides a convenient

alternative to placing used lithium-ion batteries into

the trash or municipal waste, which may be illegal in

your area.

VTech’s participation in RBRC® makes it easy for

you to drop off the spent battery at local retailers

participating in the RBRC® program or at authorized

VTech product service centers. Please call

1 (800) 8 BATTERY® for information on Li-ion

battery recycling and disposal bans/restrictions in

your area. VTech’s involvement in this program is

part of its commitment to protecting our environment

and conserving natural resources.

RBRC® and 1 (800) 8 BATTERY

are registered trademarks of the

Rechargeable Battery Recycling

Corporation.

FCC and IC regulations

FCC Part 15

This equipment has been tested and found to

comply with the requirements for a Class B digital

device under Part 15 of the Federal Communications

Commission (FCC) rules. These requirements are

intended to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However,

there is no guarantee that interference will not occur

in a particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning the

equipment off and on, the user is encouraged to

try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment

and receiver.

Connect the equipment into an outlet on a

circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV

technician for help.

WARNING: Changes or modiﬁcations to this

equipment not expressly approved by the party

responsible for compliance could void the user’s

authority to operate the equipment.

This device complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation.

To ensure safety of users, the FCC has established

criteria for the amount of radio frequency energy

that can be safely absorbed by a user or bystander

according to the intended usage of the product. This

product has been tested and found to comply with

the FCC criteria. The baby unit shall be installed

and used such that parts of all persons’ body are

maintained at a distance of approximately 8 in (20

cm) or more. The transmitter and antenna of the

parent unit shall be held at least 1 in (2.5 cm) from

your face.

This Class B digital apparatus complies with

Canadian requirement:

CAN ICES-3 (B)/NMB-3(B)

•

Industry Canada

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference,

and (2) this device must accept any interference,

including interference that may cause undesired

operation.

Privacy of communications may not be ensured when

using this product.

The term ‘’IC:‘’ before the certiﬁcation/registration

number only signiﬁes that the Industry Canada

technical speciﬁcations were met.

This product meets the applicable Industry Canada

technical speciﬁcations.

RF radiation exposure statement

The baby unit complies with FCC RF radiation

exposure limits set forth for an uncontrolled

environment. The baby unit should be installed and

operated with a minimum distance of 8 in (20 cm)

between the baby unit and all persons’ body. Use of

other accessories may not ensure compliance with

FCC RF exposure guidelines. This transmitter must

not be co-located or operating in conjunction with

any other antenna or transmitter. This equipment

complies also with Industry Canada RSS-102 with

respect to Canada’s Health Code 6 for Exposure of

Humans to RF Fields.

Limited warranty

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to

the holder of a valid proof of purchase (“Consumer”

or “you”) that the Product and all accessories

provided in the sales package (“Product”) are

free from defects in material and workmanship,

pursuant to the following terms and conditions,

when installed and used normally and in accordance

with the Product operating instructions. This limited

warranty extends only to the Consumer for Products

purchased and used in the United States of America

and Canada.

What will VTech do if the Product is not free from

defects in materials and workmanship during

the limited warranty period (“Materially Defective

Product”)?

During the limited warranty period, VTech’s

authorized service representative will repair

or replace at VTech’s option, without charge,

a Materially Defective Product. If we repair

the Product, we may use new or refurbished

replacement parts. If we choose to replace the

Product, we may replace it with a new or refurbished

Product of the same or similar design. We will

retain defective parts, modules, or equipment.

Repair or replacement of the Product, at VTech’s

option, is your exclusive remedy. VTech will return

the repaired or replacement Products to you in

working condition. You should expect the repair or

replacement to take approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends

for ONE (1) YEAR from the date of purchase. If

VTech repairs or replaces a Materially Defective

Product under the terms of this limited warranty,

this limited warranty also applies to the repaired

or replacement Product for a period of either (a)

90 days from the date the repaired or replacement

Product is shipped to you or (b) the time remaining

on the original one-year warranty; whichever is

longer.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse,

accident, shipping or other physical damage,

improper installation, abnormal operation or

handling, neglect, inundation, ﬁre, water or other

liquid intrusion; or

2. Product that has been damaged due to repair,

alteration or modiﬁcation by anyone other than an

authorized service representative of VTech; or

3. Product to the extent that the problem experienced

is caused by signal conditions, network reliability,

or cable or antenna systems; or

4. Product to the extent that the problem is caused

by use with non-VTech accessories; or

5. Product whose warranty/quality stickers, product

serial number plates or electronic serial numbers

have been removed, altered or rendered illegible; or

6. Product purchased, used, serviced, or shipped for

repair from outside the United States of America

or Canada, or used for commercial or institutional

purposes (including but not limited to Products

used for rental purposes); or

7. Product returned without a valid proof of purchase

(see item 2 on the next page); or

8. Charges for installation or set up, adjustment of

customer controls, and installation or repair of

systems outside the unit.

How do you get warranty service?

To obtain warranty service in the Canada, please

visit our website at www.vtechcanada.com or

call 1 (800) 267-7377.

NOTE: Before calling for service, please review the

user’s manual - a check of the Product’s controls

and features may save you a service call.

Except as provided by applicable law, you assume

the risk of loss or damage during transit and

transportation and are responsible for delivery or

handling charges incurred in the transport of the

Product(s) to the service location. VTech will return

repaired or replaced Product under this limited

warranty. Transportation, delivery or handling charges

are prepaid. VTech assumes no risk for damage or

loss of the Product in transit. If the Product failure

is not covered by this limited warra nty, or proof of

purchase does not meet the terms of this limited

warranty, VTech will notify you and will request that

you authorize the cost of repair prior to any further

repair activity. You must pay for the cost of repair and

return shipping costs for the repair of Products that

are not covered by this limited warranty.

What must you return with the Product to get

warranty service?

Return the entire original package and contents

including the Product to the VTech service

location along with a description of the malfunction

or difﬁculty; and

Include a “valid proof of purchase” (sales receipt)

identifying the Product purchased (Product model)

and the date of purchase or receipt; and

Provide your name, complete and correct mailing

address, and telephone number.

Other limitations

This warranty is the complete and exclusive

agreement between you and VTech. It supersedes

all other written or oral communications related to this

Product. VTech provides no other warranties for this

Product. The warranty exclusively describes all of

VTech’s responsibilities regarding the Product. There

are no other express warranties. No one is authorized

to make modiﬁcations to this limited warranty and you

should not rely on any such modiﬁcation.

State/Provincial Law Rights: This warranty gives you

speciﬁc legal rights, and you may also have other rights,

which vary from state to state or province to province.

Limitations: Implied warranties, including those of

ﬁtness for a particular purpose and merchantability (an

unwritten warranty that the Product is ﬁt for ordinary

use) are limited to one year from the date of purchase.

Some states/provinces do not allow limitations on

how long an implied warranty lasts, so the above

limitation may not apply to you. In no event shall

VTech be liable for any indirect, special, incidental,

consequential, or similar damages (including, but

not limited to lost proﬁts or revenue, inability to use

the Product or other associated equipment, the cost

of substitute equipment, and claims by third parties)

resulting from the use of this Product. Some states/

provinces do not allow the exclusion or limitation of

incidental or consequential damages, so the above

limitation or exclusion may not apply to you.

Please retain your original sales receipt as proof

of purchase.

Technical specications

Frequency

control

Crystal controlled PLL synthesizer

Transmit

frequency

Baby unit: 2406 - 2475 MHz

Parent unit: 2406 - 2475 MHz

Channels 24

LCD 4.3” Color LCD

(WQVGA 480x272 pixel)

Nominal

effective

range

Maximum power allowed by FCC

and IC. Actual operating range may

vary according to environmental

conditions at the time of use.

Power

requirements

Parent unit: 3.7V Li-polymer battery

Baby unit power adapter:

Output: 5.9V DC @ 1A

Parent unit power adapter:

Output: 5V DC @ 1A

Specifications are subject to change without notice.

Document order number: 91-008473-050-100

Produktspezifikationen

Marke:	Vtech
Kategorie:	Babyphone
Modell:	Safe & Sound VM343
Touchscreen:	Nein
Bildschirmdiagonale:	4.3 "
Eingebautes Mikrofon:	Ja
Produktfarbe:	Silver, White
Akku-/Batterietechnologie:	Lithium Polymer (LiPo)
Energiequelle:	AC, Battery
Lautstärkeregler:	Digital
Anzahl Kanäle:	24 Kanäle
LED-Anzeigen:	Ja
Montageset:	Ja
Akku-/Batteriespannung:	3.7 V
Schwenkbereich:	-135 - 135 °
Neigungswinkelbereich:	-60 - 60 °
Nachtmodus:	Ja
Batterieladeanzeige:	Ja
Warnanzeige bei geringem Ladestand:	Ja
Bis zu 30 Frames pro Sekunde:	25 fps
LED Typ:	IR
Maximale Reichweite:	300 m
Temperatursensor:	Ja
Anzahl der Beleuchtungs-LEDs:	10
Bewegungssensor:	Ja
Lärmdetektion:	Ja
Talk back-Funktion:	Ja
Display-Auflösung:	480 x 272 Pixel
Receiver Strom:	1 A
Transmitter Strom:	1 A