Vtech DM1111 Bedienungsanleitung

Vtech Babyphone DM1111

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Vtech DM1111 (4 Seiten) in der Kategorie Babyphone. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

NOTE

• theWhen POWER/LINK LED light flashes, move

the parent unit closer to the baby unit (observe the

minimum distance of 6.5 feet / 2 meters). You can

also check if the baby monitor is connected to a

live power socket and switched on.

TIP

• Increase the speaker volume of the parent unit if

you cannot hear the sounds transmitted from the

baby unit.

Positioning the baby monitor

CAUTION

• Keep the baby unit out of the reach of baby. your

Never place or mount the baby unit inside the

baby’s crib or playpen.

1. Place the baby unit more than 3 feet

(1 meter) away from your baby.

2. Place the parent unit more than 6.5 feet

(2 meters) away from the baby unit.

CAUTION

• The default volume of your parent unit is , Level 3

and the maximum volume is . If you level 5

experience high-pitched screeching noise from

your baby monitor while positioning:

-Make sure your baby unit and parent unit are

more than 6.5 feet (2 meters) apart, OR

-Turn down the volume of your parent unit.

Operating range

The operating range of the baby monitor is

up to 1,500 feet (450 meters) outdoors or

160 feet (50 meters) indoors. The actual

operating range may vary depending on

the environmental conditions and other

interferences such as walls, doors and other

obstructions.

Overview

Baby unit overview

1 (On/off)

Press and hold to turn on or off the

baby unit.

2Microphone

3POWER light

4Power jack

Parent unit overview

1 Speaker

2 (On/off)

Press and hold to turn on or off the

parent unit.

3 (Volume up)

• Press to increase the speaker

volume.

4POWER / LINK light

5Power jack

6Visual sound indicator

• Indicate the sound level detected by

the baby unit or show the volume

level during speaker volume setting.

7 (Volume down)

• Press to decrease the speaker

volume.

• Press repeatedly until the volume

reaches the minimum to mute the

parent unit.

8 (Low battery light)

9Belt clip

10 Battery compartment cover

Baby unit light

POWER

POWER light

• Lights off when the baby unit is

off.

• Lights on in green when the baby

unit is on.

Parent unit lights

POWER / LINK

POWER / LINK light

• Lights off when the parent

unit is off.

• Lights on in green when the

parent unit is on and linked

to the baby unit.

• Flashes in green when there

is no link between the baby

unit and parent unit, or when

the parent unit is out of

range from the baby unit.

Visual sound indicator

The visual sound indicator has

two functions. One is to show

the sound level detected by

the baby unit. The other one

is to show the volume level

during speaker volume setting.

Sound level detected by the

baby unit

• One to three green lights

indicate a moderate sound

level detected by the baby

unit.

• Additional red lights indicate

a higher sound level

detected by the baby unit

(e.g. baby crying loudly).

Speaker volume level

• One to three green lights

indicate Level 1 to Level

3 of the speaker volume

setting.

• Additional red lights indicate

Level 4 Level 5 to of the

speaker volume setting.

Flashes in red when the

battery is low.

Parent unit alert tones

Low

battery

tone

• Beeps twice every 10 minutes

when the battery is low.

Out of

range

tone

• Beeps three times every 30

seconds when there is no link

between the baby unit and

parent unit, or when the parent

unit is out of range from the baby

unit.

Using the baby monitor

Power on or off the baby unit

• Press and hold until the POWER light

turns on.

• Press and hold until the POWER light

turns off.

Power on or off the parent unit

• Press and hold until the POWER / LINK

light turns on.

• Press and hold until the POWER / LINK

light turns off.

Adjust speaker volume

The speaker volume is preset to Level 3

on the parent unit. You can adjust to your

preferred sound level.

• Press to decrease the volume, and to

increase the volume.

NOTE

• If you continue to press or when the

volume reaches the minimum or maximum

setting, the parent unit will beep twice.

To mute the speaker volume:

• Press repeatedly until the volume

reaches the minimum.

NOTE

• When the parent unit is in mute, the visual sound

indicator will still indicate the sound detected from

the baby unit.

• To unmute, press repeatedly until it reaches

your desired volume.

General product care

To keep this product working well and looking good,

follow these guidelines:

• Avoid putting it near heating appliances and

devices that generate electrical noise (for

example, motors or fluorescent lamps).

• DO NOT expose it to direct sunlight or moisture.

• Avoid dropping the product or treating it roughly.

• Clean with a soft cloth.

• DO NOT immerse the parent unit and the baby

unit in water and do not clean them under the tap.

• DO NOT use cleaning spray or liquid cleaners.

• Make sure the baby unit and parent unit are dry

before you connect them to the mains again.

Storage

When you are not going to use the baby monitor for

some time, remove the AAA alkaline batteries from

the parent unit. Store the parent unit, the baby unit

and the adapters in a cool and dry place.

Operating range

This product operates with the maximum power

allowed by the Federal Communications Commission

(FCC). Even so, the baby unit and the parent unit can

communicate over only a certain distance - which can

vary with the locations of the baby unit, the parent

unit, the weather, and the layout of your home. When

the parent unit is out of range, it will beep three times

every 30 seconds and enter searching mode. To

improve reception, move closer to the baby unit (but

not less than 6.5 feet / 2 meters).

Congratulations

on purchasing your new VTech product. Before

using this product, please read Important

safety instructions.

This manual has all the feature operations

and troubleshooting necessary to install and

operate your new VTech product. Please

review this manual thoroughly to ensure proper

installation and operation of this innovative and

feature rich VTech product.

For support, shopping, and everything new at

VTech, visit our website at

www.vtechphones.com.

What’s in the box

Install batteries for

temporary use

You are recommended to use the power

adapter to power up the parent unit for normal

use. If you want to move around the house

with the parent unit, install two AAA alkaline

batteries for temporary use.

NOTE

• You need to purchase two AAA alkaline batteries

separately.

NOTE

• Use 2 x AAA batteries (not included). Alkaline

batteries are recommended. If you use other kind

of batteries, the performance of the baby monitor

varies.

• The parent unit does not support battery

recharging.

• Do not mix old and new batteries. Do not mix

alkaline, standard (Carbon-Zinc) or rechargeable

(Ni-Cad, Ni-Mh, etc) batteries.

• While you insert the batteries, make sure the

polarities are correct.

• When the batteries are installed, the parent unit

turns on.

• Replace the batteries when the light flashes

on the parent unit, or you hear two beeps every

10 minutes.

Install the batteries as shown below.

1. Push to slide open the battery compartment

cover.

2. Insert two AAA alkaline batteries into the

battery compartment, according to the

polarity indications (+) and (-).

3. Slide the battery compartment cover until it

clicks into place.

Replace the battery

To replace the batteries, slide open the battery

compartment cover, and then take out the

batteries. Follow the previous steps to install

the new batteries.

Connect

NOTE

• Use only the power adapters supplied with this

product.

• The power adapters are intended to be correctly

oriented in a vertical or floor mount position. The

prongs are not designed to hold the plug in place if

they are plugged into a ceiling, under-the-table or

cabinet outlet.

• Make sure the parent unit, the baby unit and the

power adapter cords are out of reach of children.

• Both the baby unit and the parent unit are on once

connected to the power supply.

Connect the baby monitor

NOTE

• Make sure the light is on after the POWER / LINK

power plug is fully inserted into the power jack of

the parent unit.

• Make sure the baby unit is on. If the parent

unit is not linked to the baby unit, the

POWER / LINK light on the parent unit will flash.

Move the parent unit closer to the baby unit (but

not less than 6.5 feet / 2 meters).

• Make sure the light is on after the power POWER

plug is fully inserted into the power jack of the

baby unit.

Before use

NOTE

• This baby monitor is intended as an aid. It is not a

substitute for proper adult supervision, and should

not be used as such.

Test your baby monitor

You may test the baby monitor before initial

use, and at regular times thereafter.

CAUTION

• For hearing protection, make sure the parent

unit is more than 6.5 feet ( ) away 2 meters

from the baby unit. If you hear any high-

pitched noise, move the parent unit further

until the noise stops. You can also press

on the parent unit to lower or mute the noise.

1. Make sure your baby unit and parent unit

are on.

2. Speak towards the microphone of the baby

unit. You will hear the sound at the parent

unit, and see the visual sound indicators

light up.

User’s manual

DM1111

DM1111-2

Enhanced Range

Digital Audio Monitor

Go to www.vtechphones.com

to register your product for

enhanced warranty support and

the latest VTech product news.

St ra ng ul at io n

Haz a

Ke ep th is c ord out o f re ach of childre n.

Th e cord n eed s t o b e a t lea st th ree feet

awa y f

rom the child at all t ime s . D o not

us e with an ex tens ion c or d . Do no t

re move this ta g.

Élo igne z ce cord on des e nfa nt s. Le

co rdon doi t se trouv er à au mo ins t rois

pie ds d ’un enfa nt e t ce, en tou t tem ps.

N’u tilis e z p as d e rall ong e.

N e re t ire z pas

ce tt e éti qu ette .

Manten ga e ste c

abl e fu era de l a al cance

de los n iño s. Es te ca ble deb e e star p or

lo meno s tr es p ies fue ra de la a lcan ce

de l niño en tod o mo me nto . No lo u se

co n una ex tens i ón i nalá mb rica . No quite

es ta etiq ue ta.

Ris q ue

d’é tra ng le me

Rie sg o de

es tran gul ac ió n

Strang

latio n

z ar

Kee p th

is c or d out o f rea

ch of chil dren.

The cord

nee ds to b

e at le ast th ree feet

away fr o m th

e child at a ll tim

es. Do not

use w

ith an extens ion co rd

. D o not

remove t his tag.

Éloigne z c e cord on des e

nfa nts. Le

cord

on doit se trou ver à

au m

oins tro is

pieds d’un enfant e t ce, en to

ut te

mps .

N’util ise

z pas d e ra llonge . N

e re

tirez pas

cette é tiquet te.

Mantenga es t e c ab le fu era de l a alca nce

de los niños.

Es te cable debe es tar por

lo m

enos t re

s pie s fu er a de la alcanc e

del n iño en to

do m

omen to . N

o l o us e

co n una extens ión in alámbr ic

a. N

o quite

esta e tiq

ueta.

isq

’é tranglement

Ries g

o de

estra ngulación

>6.5ft (2m)

1 set for DM1111

2 sets for DM1111-2

Stra

ng ul a t

io n

Ha z a r

Kee p th

is cor d

ou t of r each of

ch ildre n

The cord nee ds to be at le

ast th ree f eet

aw ay fr om the ch ild

at all times . Do not

use wi th an e

xt ensi o

n cor d. Do no t

re move this tag.

Élo ignez ce c

ordo n d es enfants. Le

cordo n doit se t rouver à au mo ins tr ois

ieds d’

un enfant e t ce, e n

to ut tem ps.

N’u tilise z pas de

rallo ng e. N e

retire z p

cette étiqu ette

an teng a

este cable fu era

de la al

ca nce

de lo

s n iños. Es te cab

le debe e

star por

lo menos tres p

ie s fuera

de la alc

an ce

de l ni ño

en todo mo mento . No l o

use

co n u na extens ión i nalám b

rica. No q ui te

esta e tiqueta.

Ris

d ’é

tr a ngle ment

Ries go

es tr

an gula

ción

Stra ngul atio n

Ha z a r d

Kee p this cor d ou t of r eac

h o f chi ld re n.

The cord nee d s t o b e at leas t three fee t

aw ay f

rom t he

child at

all t imes. Do no

use wi th an ext e

nsio n co

rd. Do n

move

th is ta g.

Élo i gnez ce cor d on d es

enf ant s.

cordo n d

oit se tro

uv er à a u m oins t

ro is

pie

ds d’un enfant e

t ce, en tou t tem p

N’ut ili

sez pas de ra llonge. Ne r et

irez pas

cette

éti quet

te.

nten ga est e cable fue ra d e la alca n

de los

n iños. E ste cable d

ebe es

tar por

lo meno s tres pies fuera de la alcan ce

de l niñ o

en todo mo m ento . No lo use

co n u na ex tensió n

ina lámbr ica. No q

uite

esta etiq u eta

Risq ue

d’é tr

angle m e nt

Rie s go de

es t

ra ng

ul ac ión

> 3ft (1m)

< 6.5ft (2m)

> 6.5ft (2m)

Frequently asked questions

Below are the questions most frequently asked about

the baby monitor. If you cannot find the answer to your

question, visit our website at www.vtechphones.com,

or contact for customer service.1 (800) 595-9511

Why doesn’t

the POWER

light on the

baby unit turn

on when I

switch on the

units?

Perhaps the baby unit is not

connected to the power supply.

Connect the baby unit to power

supply. The baby unit turns on.

Why doesn’t

the POWER

/ LINK light

on the parent

unit turn on

when I switch

on the units?

Perhaps the battery of the parent

unit is empty and the parent unit is

not connected to power supply.

Connect the parent unit to power

supply; or insert two new AAA

alkaline batteries into the parent

unit. The parent unit turns on and

establishes connection with the

baby unit.

Why does the

baby monitor

not respond

normally?

Try the following (in the order

listed) for common cure:

1. Make sure that both baby

unit and parent unit are on.

Disconnect the power from the

baby unit and the parent unit.

2. Remove the batteries from the

parent unit.

3. Connect the baby unit to the

power supply again. The baby unit

turns on.

4. Connect the parent unit to the

power supply again; or insert

two new AAA alkaline batteries.

The parent unit turns on.

5. Wait for the parent unit to

synchronize with the baby unit.

Allow up to one minute for this

to take place.

6. Press or to adjust the

speaker volume on the parent

unit.

Why does the

baby monitor

produce a

high-pitched

noise?

The units may be too close to

each other. Make sure the parent

unit and the baby unit at least

6.5 feet / 2 meters away from each

other.

Why don’t I

hear a sound/

Why can’t I

hear my baby

cry?

Make sure that both baby unit and

parent unit are on. If you see the

visual sound indicators light up,

but there is no sound, then you

may have muted the volume or

set it to a lower level. Adjust the

volume to a higher level.

If the visual sound indicators do

not light up, and you cannot hear

any sound, it is because the baby

sound is too low for the baby unit

to detect. This is normal. Place

the baby unit at least 6.5 feet / 2

meters away from your baby.

Why does the

parent unit

beep?

The parent unit beeps three times

every 30 seconds when the baby

unit is out of range. Move the

parent unit closer to the baby

unit (but not less than 6.5 feet / 2

meters).

If the parent unit is powered by

batteries, the parent unit beeps

twice every 10 minutes and the

light flashes in red when the

battery is low. Replace with two

new AAA alkaline batteries.

Why does

the parent

unit light

flash?

If the parent unit is powered by

batteries, the parent unit beeps

twice every 10 minutes and the

light flashes in red when the

battery is low. Replace with two

new AAA alkaline batteries, or

remove the batteries, and connect

the parent unit to the power supply.

Why can’t I

establish a

connection?

Why is the

connection

lost every

now and

then? Why

are there

sound

interruptions?

The baby unit may be out of range.

Move the parent unit closer to the

baby unit (but not less than

6.5 feet / 2 meters).

Other electronic products may

cause interference with your baby

monitor. Try installing your baby

monitor as far away from these

electronic devices as possible.

Important safety instructions

When using your equipment, basic safety

precautions should always be followed to

reduce the risk of fire, electric shock and

injury, including the following:

1. Follow all warnings and instructions marked on

the product.

2. Adult setup is required.

3. This product is intended as an aid. It is not

a substitute for responsible and proper adult

supervision and should not be used as such.

4. This product is not intended for use as a medical

monitor.

5. Do not use this product near water. For example,

do not use it next to a bath tub, wash bowl,

kitchen sink, laundry tub or swimming pool, or in

a wet basement or shower.

6. Use only alkaline batteries (not CAUTION:

included). There may be a risk of explosion if a

wrong type of battery is used for the parent unit.

Do not dispose of batteries in a fire. They may

explode. Check with local codes for possible

special disposal instructions.

7. Use only the adapters included with this product.

Incorrect adapter polarity or voltage can

seriously damage the product.

Baby unit power adapter: Input: 100-120V AC 60

Hz; output: 6V DC 400 mA

Parent unit power adapter: Input: 100-120V AC 60

Hz Output: 6V DC 400mA.

8. The power adapters are intended to be correctly

oriented in a vertical or floor mount position. The

prongs are not designed to hold the plug in place

if it is plugged into a ceiling, under-the-table or

cabinet outlet.

9. For pluggable equipment, the socket-outlet

shall be installed near the equipment and shall

be easily accessible.

10. Unplug this product from the wall outlet before

cleaning. Do not use liquid or aerosol cleaners.

Use a damp cloth for cleaning.

11. Unplug the power cords before replacing batteries.

12. Do not cut off the power adapters to replace

them with other plugs, as this causes a

hazardous situation.

13. Do not allow anything to rest on the power cords.

Do not install this product where the cords may

be walked on or crimped.

14. This product should be operated only from the

type of power source indicated on the marking

label. If you are not sure of the type of power

supply in your home, consult your dealer or local

power company.

15. Do not overload wall outlets or use an extension

cord.

16. Do not place this product on an unstable table,

shelf, stand or other unstable surfaces.

17. This product should not be placed in any area

where proper ventilation is not provided. Slots

and openings in the back or bottom of this

product are provided for ventilation. To protect

them from overheating, these openings must

not be blocked by placing the product on a soft

surface such as a bed, sofa or rug. This product

should never be placed near or over a radiator or

heat register.

18. Never push objects of any kind into this product

through the slots because they may touch

dangerous voltage points or create a short circuit.

Never spill liquid of any kind on the product.

19. To reduce the risk of electric shock, do not

disassemble this product, but take it to an

authorized service facility. Opening or removing

parts of the product other than specified

access doors may expose you to dangerous

voltages or other risks. Incorrect reassembling

can cause electric shock when the product is

subsequently used.

20. You should test the sound reception every

time you turn on the units or move one of the

components.

21. Periodically examine all components for

damage.

22. Be aware of possible loss of privacy while using

public airwaves. Conversations may be picked

up by other nursery monitors, cordless phones,

scanners, etc.

23. Children should be supervised to ensure that

they do not play with the product.

24. The product is not intended for use by persons

(including children) with reduced physical,

sensory or mental capabilities, or lack of

experience and knowledge, unless they have

been given supervision or instruction concerning

use of the appliance by a person responsible for

their safety.

SAVE THESE INSTRUCTIONS

Cautions

1. Use and store the product at a temperature

between 32oF and 104oF.

2. Do not expose the product to extreme cold, heat

or direct sunlight. Do not put the product close to

a heating source.

3. Batteries should not be exposed to excessive

heat such as bright sunshine or fire.

4. Make sure the baby unit and the adapter cord

are always out of reach of the baby, at least 3

feet (1 meter) away from the baby or crib, to

avoid a possible strangulation hazard.

5. Never place the baby unit(s) inside the baby’s crib

or playpen. Never cover the baby unit(s) or parent

unit with anything such as a towel or a blanket.

6. Never cover the baby unit or parent unit(s) with

anything such as a towel or a blanket.

7. Other electronic products may cause

interference with your baby monitor. Try

installing your baby monitor as far away from

these electronic devices as possible: wireless

routers, radios, cellular telephones, intercoms,

room monitors, televisions, personal computers,

kitchen appliances and cordless telephones.

Precautions for users of implanted cardiac

pacemakers

Cardiac pacemakers (applies only to digital cordless

devices):

Wireless Technology Research, LLC (WTR), an

independent research entity, led a multidisciplinary

evaluation of the interference between portable

wireless devices and implanted cardiac

pacemakers. Supported by the U.S. Food and Drug

Administration, WTR recommends to physicians that:

Pacemaker patients

• Should keep wireless devices at least six inches

from the pacemaker.

• Should NOT place wireless devices directly over

the pacemaker, such as in a breast pocket, when

it is turned ON.

WTR’s evaluation did not identify any risk to

bystanders with pacemakers from other persons

using wireless devices.

Electromagnetic fields (EMF)

This VTech product complies with all standards

regarding electromagnetic fields (EMF). If handled

properly and according to the instructions in this

user’s manual, the product is safe to be used based

on scientific evidence available today.

FCC and IC regulations

FCC Part 15

This equipment has been tested and found to

comply with the requirements for a Class B digital

device under Part 15 of the Federal Communications

Commission (FCC) rules. These requirements are

intended to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However,

there is no guarantee that interference will not occur

in a particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning the

equipment off and on, the user is encouraged to

try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment

and receiver.

• Connect the equipment into an outlet on a

circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV

technician for help.

WARNING: Changes or modifications to this

equipment not expressly approved by the party

responsible for compliance could void the user’s

authority to operate the equipment.

This device complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation.

To ensure safety of users, the FCC has established

criteria for the amount of radio frequency energy

that can be safely absorbed by a user or bystander

according to the intended usage of the product. This

product has been tested and found to comply with

the FCC criteria. The baby unit shall be installed

and used such that parts of all persons’ body are

maintained at a distance of approximately 8 in (20

cm) or more.

This Class B digital apparatus complies with

Canadian requirement:

CAN ICES-3 (B)/NMB-3(B)

Industry Canada

This device complies with Industry Canada

licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference

received, and (2) this device must accept any

interference received, including interference that may

cause undesired operation.

The term ‘’IC:‘’ before the certification/registration

number only signifies that the Industry Canada

technical specifications were met.

This product meets the applicable Innovation,

Science and Economic Development Canada

technical specifications.

RF radiation exposure statement

The baby unit complies with FCC RF radiation

exposure limits set forth for an uncontrolled

environment. The baby unit should be installed

and operated with a minimum distance of 20 cm

(8 inches) between the baby unit and all persons’

body. For body worn operation, this parent unit

has been tested and meets the FCC RF exposure

guidelines. Use of other accessories may not ensure

compliance with FCC RF exposure guidelines. This

transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter.

This equipment complies also with Industry Canada

RSS-102 with respect to Canada’s Health Code 6 for

Exposure of Humans to RF Fields.

For cETL compliance only

Mesures de sécurité importantes

Lorsque vous utilisez votre appareil, vous devriez

toujours suivre certaines mesures de précaution

de base afin de réduire les risques d’incendie,

d’électrocution et de blessures corporelles, dont

ceux qui suivent :

1. Observez toutes les instructions et mises en

garde inscrites sur l’appareil.

2. L’installation par un adulte est requise.

3. Ce produit a été conçu pour être un dispositif

d’appoint seulement. Il n’est pas le remplacement

d’une supervision responsable et adéquate par un

adulte et ne devrait pas être utilisé comme telle.

4. Ce produit n’est pas conçu pour être utilisé en

tant que moniteur médical.

5. N’utilisez pas cet appareil près de l’eau ni de

toute autre source d’humidité, par exemple, près

d’une baignoire, cuve à lessive, évier de cuisine,

dans un sous-sol humide ni près d’une piscine,

dans un soussol humide ou une douche.

6. MISE EN GARDE : Il peut y avoir un risque

d’explosion si vous utilisez le mauvais type de

bloc-piles pour l’unité du parent. N’incinérez pas

les piles. Celles-ci risqueraient d’exploser.

7. N’utilisez que les adaptateurs inclus avec ce

produit. L’utilisation d’un adaptateur dont la

polarité ou la tension serait inadéquate risque

d’endommager sérieusement le produit et mettre

votre sécurité en péril.

Adaptateur de l’unité du bébé :

Entrée 100-120V AC 60 Hz; Sortie : 6V DC

400 mA

Adaptateur de l’unité du parent :

Entrée 100-120V AC 60 Hz; Sortie : 6V DC

400 mA

8. Lorsqu’ils sont branchés dans une prise de

courant, les adaptateurs secteur ont été conçus

pour être orientés correctement, soit à la

verticale ou au plancher. Les broches n’ont pas

été conçues pour supporter le poids du bloc

d’alimentation et le maintenir en place si celuici

est branché dans une prise au plafond, sous une

table ou dans un meuble.

9. Pour les PRODUITS À BRANCHER À UNE

PRISE DE COURANT, la prise de courant doit

être installée près du produit, afin d’assurer une

accessibilité sécuritaire à la prise de courant.

10. Débranchez ce produit de la prise de courant

avant de procéder au nettoyage. N’utilisez pas de

nettoyants en aérosols. Utilisez un chiffon humide

pour le nettoyer.

11. Débranchez les cordons d’alimentation avant de

remplacer le bloc-piles.

12. Ne coupez pas les cordons d’alimentation pour

remplacer les fiches, car ceci peut présenter un

danger potentiel.

13. Ne laissez aucun objet reposer ni appuyer sur

le cordon d’alimentation. N’installez pas cet

appareil dans un endroit où l’on risque d’écraser

le cordon d’alimentation ou de le piétiner.

14. Ne faites fonctionner cet appareil qu’avec le

type d’alimentation indiqué sur l’étiquette. Si

vous ne connaissez pas le type d’alimentation

que vous possédez à votre domicile, consultez

votre marchand ou votre compagnie locale

d’électricité.

15. Ne surchargez pas les prises de courant

murales ni les rallonges électriques.

16. Ne placez pas cet appareil sur un chariot,

meuble, trépied, support de montage ni table

chancelants.

17. Les trous et ouvertures du boîtier, situés à

l’arrière de l’appareil ou sous celui-ci, servent à

aérer l’appareil. Pour l’empêcher de surchauffer,

ne bloquez sous aucun prétexte ces ouvertures

et n’empêchez pas l’aération adéquate de

l’appareil en le plaçant sur un lit, divan, tapis ou

toute autre surface similaire. De même, ne le

positionnez pas à proximité ni au-dessus d’une

source de chaleur ou d’un calorifère. De plus, ne

placez pas l’appareil dans un endroit avant de

vous assurer qu’il y ait une bonne circulation d’air.

18. N’enfoncez jamais d’objets à travers les

ouvertures de cet appareil, car ils pourraient

entrer en contact avec des points de tension

dangereux ou causer des courts-circuits qui

peuvent dégénérer en incendies ou en risques

d’électrocution. Ne renversez jamais de liquide

dans ce produit.

19. Afin de réduire les risques d’électrocution, ne

démontez pas cet appareil, mais apportez-le

dans un centre de service autorisé. L’ouverture

du boîtier ou le retrait de toutes pièces que

contient cet appareil, à l’exception de l’accès

autorisé à certaines portes ou ouvertures,

risque de vous exposer à des points de tension

dangereux ou d’autres dangers. Un remontage

incorrect peut par la suite présenter des risques

d’électrocution.

20. Vous devriez tester la réception chaque fois que

vous mettez l’appareil en fonction.

21. Examinez les composantes afin de vérifier si

celles-ci ne sont pas endommagées.

22. Soyez avisé de la perte de la confidentialité

lorsque vous utilisez les ondes publiques. Les

conversations peuvent être entendues par

d’autres moniteurs de bébé, des téléphones

sans fil, des scanneurs, etc.

23. Les enfants devraient être supervisés afin de

vous assurer qu’ils ne jouent pas avec l’appareil.

24. Le produit n’est pas conçu pour être utilisé

par des personnes (incluant des enfants) aux

capacités physiques, sensorielles ou mentales

réduites ou qui manquent d’expérience et de

connaissances, à moins qu’on leur ait donné

suffisamment de supervision ou d’instructions

relativement à l’utilisation de l’appareil par une

personne responsable de leur sécurité.

CONSERVEZ CES INSTRUCTIONS

Mises en garde

1. Utilisez et entreposez le produit à une

température entre 0˚ C (32˚F) et 40˚C (104˚ F).

2. N’exposez pas cet appareil à des froids ou des

chaleurs extrêmes, ainsi qu’à la lumière directe

du soleil. Ne l’installez pas près d’une source de

chauffage.

3. Le bloc-piles ne doit pas être exposé à la chaleur

excessive telle que la lumière du soleil ou au feu.

4. Assurez-vous que le moniteur et le cordon

de l’adaptateur sont toujours hors de portée

des enfants, à au moins 1 mètre (3 pieds) de

l’enfant ou du berceau, pour éviter tout risque de

strangulation.

5. Ne jamais placer le moniteur à l’intérieur du

berceau ou du parc de bébé. Ne jamais couvrir

le moniteur ou l’unité (s) portative avec un article

tel une serviette ou une couverture.

6. D’autres équipements électroniques peuvent

produire des interférences sur votre moniteur

vidéo et audio. Tentez d’installer votre

moniteur vidéo ou audio à l’écart des appareils

électroniques tels que des routeurs sans fil,

radios, téléphones cellulaires, interphones,

moniteurs, téléphones, ordinateurs personnels,

électroménagers et téléphones sans fil.

Stimulateurs cardiaques implantés dans

l’organisme

Les simulateurs cardiaques (ne s’applique qu’aux

dispositifs numériques sans fil) :

L’organisme ‘Wireless Technology Research, LLC

(WTR)’, une firme de recherche indépendante,

a mené une évaluation pluridisciplinaire des

interférences entre les téléphones sans fil portatifs

et les stimulateurs cardiaques implantés dans

l’organisme. Appuyée par l’Administration des

aliments et drogues (FDA) des États-Unis, la firme

WTR recommande aux médecins:

Avis aux détenteurs de stimulateurs

cardiaques

• Vous devriez maintenir les dispositifs sans fil à au

moins six pouces du simulateur cardiaque.

• Ils ne doivent PAS placer le téléphone sans fil

directement sur le stimulateur cardiaque, tel que

dans une poche de chemise, lorsque celui-ci est

en marche.

L’étude effectuée par l’organisme WRS n’a pas

identifié de risque pour les détenteurs de simulateurs

cardiaques causés par les gens qui utilisent

dispositifs sans fil à proximité de ceux-ci.

Champs électromagnétiques (EMF)

Ce produit de VTech est conforme à toutes

les normes se rapportant aux champs

électromagnétiques (EMF) standard. Si vous le

manipulez correctement en suivant les instructions

de ce guide, son utilisation sera sécuritaire pendant

de nombreuses années, selon les meilleures

évidences scientifiques dont nous disposons

aujourd’hui.

Limited warranty

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to

the holder of a valid proof of purchase (“Consumer”

or “you”) that the Product and all accessories

provided in the sales package (“Product”) are

free from defects in material and workmanship,

pursuant to the following terms and conditions,

when installed and used normally and in accordance

with the Product operating instructions. This limited

warranty extends only to the Consumer for Products

purchased and used in the United States of America

and Canada.

What will VTech do if the Product is not free from

defects in materials and workmanship during

the limited warranty period (“Materially Defective

Product”)?

During the limited warranty period, VTech’s

authorized service representative will repair

or replace at VTech’s option, without charge,

a Materially Defective Product. If we repair

the Product, we may use new or refurbished

replacement parts. If we choose to replace the

Product, we may replace it with a new or refurbished

Product of the same or similar design. We will

retain defective parts, modules, or equipment.

Repair or replacement of the Product, at VTech’s

option, is your exclusive remedy. VTech will return

the repaired or replacement Products to you in

working condition. You should expect the repair or

replacement to take approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends

for ONE (1) YEAR from the date of purchase. If

VTech repairs or replaces a Materially Defective

Product under the terms of this limited warranty,

this limited warranty also applies to the repaired

or replacement Product for a period of either (a)

90 days from the date the repaired or replacement

Product is shipped to you or (b) the time remaining

on the original one-year warranty; whichever is

longer.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse,

accident, shipping or other physical damage,

improper installation, abnormal operation or

handling, neglect, inundation, fire, water or other

liquid intrusion; or

2. Product that has been damaged due to repair,

alteration or modification by anyone other than an

authorized service representative of VTech; or

3. Product to the extent that the problem experienced

is caused by signal conditions, network reliability,

or cable or antenna systems; or

4. Product to the extent that the problem is caused

by use with non-VTech accessories; or

5. Product whose warranty/quality stickers, product

serial number plates or electronic serial numbers

have been removed, altered or rendered illegible;

6. Product purchased, used, serviced, or shipped for

repair from outside the United States of America

or Canada, or used for commercial or institutional

purposes (including but not limited to Products

used for rental purposes); or

7. Product returned without a valid proof of purchase

(see item 2 in the next column); or

8. Charges for installation or set up, adjustment of

customer controls, and installation or repair of

systems outside the unit.

How do you get warranty service?

To obtain warranty service in the USA, please visit

our website at www.vtechphones.com or

call 1 (800) 595-9511. In Canada, go to

www.vtechcanada.com or call 1 (800) 267-7377.

NOTE: Before calling for service, please review the

user’s manual - a check of the Product’s controls

and features may save you a service call.

Except as provided by applicable law, you assume

the risk of loss or damage during transit and

transportation and are responsible for delivery or

handling charges incurred in the transport of the

Product(s) to the service location. VTech will return

repaired or replaced Product under this limited

warranty. Transportation, delivery or handling

charges are prepaid. VTech assumes no risk for

damage or loss of the Product in transit. If the Product

failure is not covered by this limited warranty, or proof

of purchase does not meet the terms of this limited

warranty, VTech will notify you and will request that

you authorize the cost of repair prior to any further

repair activity. You must pay for the cost of repair and

return shipping costs for the repair of Products that

are not covered by this limited warranty.

What must you return with the Product to get

warranty service?

1. Return the entire original package and contents

including the Product to the VTech service

location along with a description of the malfunction

or difficulty; and

2. Include a “valid proof of purchase” (sales receipt)

identifying the Product purchased (Product model)

and the date of purchase or receipt; and

3. Provide your name, complete and correct mailing

address, and telephone number.

Other limitations

This warranty is the complete and exclusive

agreement between you and VTech. It supersedes

all other written or oral communications related to this

Product. VTech provides no other warranties for this

Product. The warranty exclusively describes all of

VTech’s responsibilities regarding the Product. There

are no other express warranties. No one is authorized

to make modifications to this limited warranty and you

should not rely on any such modification.

State/Provincial Law Rights: This warranty gives you

specific legal rights, and you may also have other

rights, which vary from state to state or province to

province.

Limitations: Implied warranties, including those of

fitness for a particular purpose and merchantability (an

unwritten warranty that the Product is fit for ordinary

use) are limited to one year from the date of purchase.

Some states/provinces do not allow limitations on

how long an implied warranty lasts, so the above

limitation may not apply to you. In no event shall

VTech be liable for any indirect, special, incidental,

consequential, or similar damages (including, but

not limited to lost profits or revenue, inability to use

the Product or other associated equipment, the cost

of substitute equipment, and claims by third parties)

resulting from the use of this Product. Some states/

provinces do not allow the exclusion or limitation of

incidental or consequential damages, so the above

limitation or exclusion may not apply to you.

Please retain your original sales receipt as proof

of purchase.

Technical specifications

Frequency

control

Crystal controlled PLL synthesizer

Transmit

frequency

Baby unit: 1921.536 - 1928.448 MHz

Parent unit: 1921.536 - 1928.448 MHz

Channels 5

Nominal

effective

range

Maximum power allowed by FCC

and IC. Actual operating range may

vary according to environmental

conditions at the time of use.

Power

requirements

Baby unit adapter:

Input: 100-120V AC 60Hz

Output: 6V DC @ 400mA

Parent unit adapter:

Input: 100-120V AC 60Hz

Output: 6V DC @ 400mA

Parent unit battery:

2 X AAA alkaline batteries

Specifications are subject to change without notice.

Document order number: 91-010894-020-100

Produktspezifikationen

Marke:	Vtech
Kategorie:	Babyphone
Modell:	DM1111

Brauchst du Hilfe?

Wenn Sie Hilfe mit Vtech DM1111 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Babyphone Vtech

Vtech Clear Sounds Deluxe Bedienungsanleitung

2 Oktober 2024

Vtech Clear Sounds Bedienungsanleitung

12 September 2024

Vtech RM5766HD Bedienungsanleitung

31 August 2024

Vtech Bel & Tel Bedienungsanleitung

23 August 2024

Vtech DM1111 Bedienungsanleitung

16 August 2024

Vtech RM5762 Bedienungsanleitung

6 August 2024

Vtech Peppa Pig Bedienungsanleitung

2 August 2024

Vtech Safe & Sound VM341 Bedienungsanleitung

29 Juli 2024

Vtech Sleepy Bear Bedienungsanleitung

28 Juli 2024

Vtech VM333-2 Bedienungsanleitung

19 Juli 2024

Bedienungsanleitung Babyphone

Neueste Bedienungsanleitung für -Kategorien-

Alecto DBX-72 ECO Bedienungsanleitung

9 Oktober 2024

Reer Neo 200 Bedienungsanleitung

8 Oktober 2024

Babymoov High Care A014009 Bedienungsanleitung

7 Oktober 2024

Topcom KS-4241 Bedienungsanleitung

3 Oktober 2024

Lorex BB1811 Bedienungsanleitung

2 Oktober 2024

Alecto DVM-75C Bedienungsanleitung

2 Oktober 2024

TrueLife NannyCam V24 Pro Bedienungsanleitung

1 Oktober 2024

TrueLife NannyCam H32 Pro Bedienungsanleitung

1 Oktober 2024

Uniden GC43W Bedienungsanleitung

30 September 2024

EMOS H100BF-CE Bedienungsanleitung

29 September 2024