Vtech BM5100-Bear Bedienungsanleitung

Vtech Babyphone BM5100-Bear

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Vtech BM5100-Bear (2 Seiten) in der Kategorie Babyphone. Dieser Bedienungsanleitung war für 29 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
Note
• This baby monitor is intended as an aid. It is not a substitute for proper adult supervision, and should
not be used as such.
Test your baby monitor
You may test the baby monitor before initial use, and at regular times thereafter.
Caution
• For hearing protection, make sure the unit is more parent
than 1 metre away from the baby unit(s). If you hear any
high-pitched noise, move the parent unit further until the
noise stops. You can also press on the parent unit to
reduce the noise.
1. Make sure your baby unit and parent unit are on.
2. The parent unit displays images from the baby unit.
• Speak towards the microphone of the baby unit.
You will hear the sound at the parent unit.
3. If you have two baby units, press on your parent VIEW
unit. The screen switches to the other baby unit. Then, repeat step 2.
Note
• When the parent unit displays , and then No Link to CAM # (# represents the baby unit number)
and the LED light flashes, move the parent unit closer to the baby unit (observe the minimum LINK
distance of 1 metre).
Tip
• Increase the speaker volume of the parent unit if you cannot hear the sounds transmitted from the
baby units.
Positioning the baby monitor
Caution
• Keep the baby unit out of the reach of baby. Never place or mount the baby unit inside the your
baby’s crib or playpen.
Note
• To avoid interference from other electronic
devices, place your baby monitor at least 1
metre away from devices such as wireless routers,
microwaves, cell phones and computers.
1. Place the baby unit more than 1 metre away from your baby.
2. Place the parent unit more than 1 metre away from the baby unit(s) to avoid screeching
noise.
Caution
The default volume of your parent unit is level , and the maximum volume is level 4 7. If you experience
high-pitched screeching noise from your baby monitor while positioning:
- Make sure your baby unit and parent unit are more than 1 metre apart, OR
- Lower the volume of your parent unit.
Power on or off the baby unit
• the switch to to turn on the baby unit. The LED light turns on.Slide ON/OFF ON ON/OFF
• the switch to to turn off the baby unit. The LED light turns off.Slide ON/OFF OFF ON/OFF
Power on or off the parent unit
• Press and hold on. to turn on the parent unit. The screen turnsPOWER
• Press and hold to turn off the parent unit. The screen turns off.POWER
Turn on or off the parent unit screen
You can turn on or off the parent unit screen without powering off the parent unit. You can still
hear sound from the baby unit.
• Press and hold on the parent unit to turn off the screen.LCD ON/OFF
• Press any key on the parent unit to turn on the screen again.
Adjust the speaker volume
For parent unit:
• on the parent unit at any time when viewing imagesPress / .
For baby unit:
Press VOL / VOL to adjust the listening volume. The baby unit speaker volume
determines the lullaby volume and talkback volume transmitted from parent unit. Level 1 is the
softest while Level 5 is the loudest.
1. when the parent unit is idle.Press MENU
2. or to choose , then press .Press Camera SELECT
3. or to choose Press Volume on Camera, then press SELECT.
4. or to choose the desired volume level, then press to confirm your Press SELECT
selection.
Adjust LCD brightness
You can change the brightness of the parent unit screen from to . The LCD Level 1 Level 5
brightness is preset to .Level 3
1. when the parent unit is idle.Press MENU
2. or to choose , then press .Press Brightness SELECT
3. or to choose the desired level of brightness, then press to confirm your Press SELECT
selection.
User’s manual
For product support please call:
1300 369 193
Congratulations
on purchasing your new VTech product. Before using this product, please read Important safety
instructions.
This manual has all the feature operations and troubleshooting necessary to install and operate
your new VTech product. Please review this manual thoroughly to ensure proper installation and
operation of this innovative and feature-rich VTech product.
1
Connect and charge the battery
What’s in the box
2
Before use
3
Using the baby monitor
3 Using the baby monitor ( )Con’t
Operating range
The operating range of the baby monitor is up to 300 metres outdoors or 50 metres indoors.
The actual operating range may vary depending on the environmental conditions and other
interferences such as walls, doors and other obstructions.
Zoom
You can zoom in while viewing images from the baby unit .
• to zoom in. Press
• Press again to zoom out.
Talk
You can use the function of the parent unit to comfort your baby in TALK Single CAM and Patrol
mode.
1. Press and hold on the parent unit. The light turns on.TALK TALK
2. Speak towards the microphone on the parent unit. Your voice is broadcast to the baby unit.
3. Release TALK to stop the broadcast. The TALK light goes off. The speaker is then turned on for
around 20 seconds, so you can hear your baby.
Note
• parent unit speaker is muted during voice broadcast. Sound transmission from the baby unit resumes The
after TALK is released.
Lullaby
The baby monitor has five lullabies and four soothing sounds for you to comfort your baby.You can
play the lullabies or soothing sounds on the baby unit using the parent unit.
To play lullaby using the parent unit:
1. when the parent unit is idle.Press MENU
2. or to choose Press Lullaby, then press .SELECT
3. or to choose , then press .Press Play Melodies SELECT
4. or to choose a lullaby, then press .Press SELECT
To play soothing sound using the parent unit:
1. when the parent unit is idle.Press MENU
2. or to choose Press Lullaby,then press .SELECT
3. or to choose Press Play Soothing Sounds, then press SELECT.
4. or to choose a soothing sound, then press .Press SELECT
Notes
• The lullaby playback on the baby unit will be paused when receiving talkback from the parent unit.
To stop playing lullaby or soothing sound:
1. when the parent unit is idle.Press MENU
2. or to choose Press Lullaby,then press .SELECT
3. or to choose , then press .Press Stop SELECT
To set auto timer for lullaby:
While the baby unit is playing lullaby or soothing sound, the auto timer feature helps you
automatically stop the lullaby or soothing sound after playing for 15/30/45/60 minutes. You can set
auto timer for lullaby with the parent unit.
1. when the parent unit is idle.Press MENU
2. or to choose Press Lullaby,then press .SELECT
3. or to choose Press Auto Timer, then press .SELECT
4. or to choose the desired lullabies duration, then press .Press SELECT
After 15/30/45/60 minutes, the lullaby or soothing sound will stop automatically.
Set sleep timer (Sound activation)
You can set the auto screen-off timer so that the LCD will turn off automatically when the parent unit
does not detect sound for the period of time you set (1, 2 or 3 minutes).
1. when the parent unit is idle.Press MENU
2. or to choose Press Sleep timer, then press .SELECT
3. or to choose the desired idle time for the LCD to turn off automatically, or choose Press
Off, then press .SELECT
After 1/2/3 minutes, the parent unit screen will turn off automatically. If you have chosen
Off, there will no sleep timer set. The parent unit screen will turn on when sound is detected
coming from the baby unit. The level of noise to enable the screen to be sound activated depends
on the sound sensitivity level set (see below).
Adjust the sound sensitivity of the baby unit
You can choose to hear sounds from the baby unit all the time, or to hear sounds that exceed a
certain level. You can use the parent unit to adjust the microphone sensitivity of your baby unit from
Lowest to Highest. The higher the sensitivity level, the more sensitive the baby unit is in detecting
sounds for transmitting to the parent unit. The VOX sound sensitivity level is preset to .Highest
Sensitivity
Level
Description
Highest
Low sensitivity
High sensitivity Highest VOX sensitivity level
The parent unit speaker is constantly on, and you will hear all sounds (including
background noises) from your baby’s room.
High
High VOX sensitivity level
The parent unit speaker turns on for soft babbling and louder sounds from your baby.
It remains quiet when your baby sleeps soundly.
Medium
Medium VOX sensitivity level
The parent unit speaker turns on for loud babbling and louder sounds from your
baby. It remains quiet when your baby makes soft sounds.
Low
Low VOX sensitivity level
The parent unit speaker turns on for crying and louder sounds from your baby. It
remains quiet when your baby makes soft sounds.
Lowest
Lowest VOX sensitivity level
The parent unit speaker turns on for loud crying or screeching sounds from your baby.
It remains quiet when your baby makes soft sounds.
1. when the parent unit is idle.Press MENU
2. or to choose Press Sensitivity (VOX setting), then press SELECT.
3. or to choose the desired sensitivity level, then press to confirm your selection.Press SELECT
Tip
• You can adjust the baby unit placement to improve the sound detection.
Set alert tone
No link alert
You can set the parent unit to beep when the link between the parent unit and the baby unit is lost.
1. when the parent unit is idle.Press MENU
2. or to choose Press Alert Tone, then press SELECT.
3. or to choose , then press .Press No Link Alert SELECT
4. or to choose or Press On Off, then press to confirm your selection. SELECT
Low battery tone
You can set the parent unit to beep when the parent unit operates in low battery condition.
1. when the parent unit is idle.Press MENU
2. or to choose Press Alert Tone, then press SELECT to select.
3. again to choose Press SELECT
Low Battery Tone.
4. or to choose or Press On Off, then press to confirm your selection.SELECT
Monitor the temperature
Your baby unit monitors the temperature of your baby’s room with its built-in temperature sensor. If
the detected temperature is outside of the preset temperature range, the parent unit will display alert
message.
Set temperature range
You can set the desired room temperature alert range. The minimum temperature can be set
between 11 oC (52 oF ) and 20 oC (69 oF).
The maximum temperature can be set between 21 oC (70 oF) and 30 oC (86 oF).
1. when the parent unit is idle.Press MENU
2. or to choose Press Temperature, then press SELECT.
3. or to choose , then press .Press Minimum or Maximum SELECT
4. or to choose the desired minimum or maximum temperature, then press to Press SELECT
confirm your selection.
Temperature alert tone
You can turn on the temperature alert tone so that the parent unit will emit an alert tone if the
detected temperature is out of range.
1. when the parent unit is idle.Press MENU
2. or to choose Press Temperature, then press SELECT.
3. or to choose , then press .Press Set alert SELECT
4. or to choose or Press On Off, then press to confirm your selection.SELECT
Temperature format
You can choose to display the temperature in Fahrenheit (oF) or Celsius (oC).
1. when the parent unit is idle.Press MENU
2. or to choose Press Temperature, then press SELECT.
3. or to choose , then press .Press Format SELECT
4. or to choose Press oF or oC, then press SELECT to confirm your selection.
Turn on or off the vibration
You can turn on the vibration feature so that the parent unit vibrates when it receives any of No link
alert or Temperature alert tone after turning on the respective alert tones.
1. when the parent unit is idle.Press MENU
2. or to choose , then press .Press Vibration SELECT
3. or to choose or .Press On Off
4. to confirm your selection.Press SELECT
Note
• If the vibration feature is turned on, the parent unit may vibrate as it receives sound broadcast from the baby unit.
The vibration alert for sound detection will only vibrate approximately every 20-30 seconds.
Monitoring mode * for pairing with BM5110-BEAR only
Every time the parent unit is turned on, it displays a baby unit in mode. If there are two Single CAM
baby units in your system, you can also monitor your baby in Patrol or Split mode.
Single CAM The screen displays image of a single baby unit in full screen.
Patrol A single cam view that transitions to a different baby unit every 10 seconds.
Split The screen displays all baby units.
You can choose the desired monitoring mode.
1. Press when the parent unit is idle.MENU
2. Press or to choose Monitoring Mode, then press SELECT.
3. Press or to choose , or , then press .Single CAM Patrol Split SELECT
In Single CAM or Patrol mode:
• Press to view the next baby unit.VIEW
In Split mode:
• Press , , to select a baby unit. or
• Press or VIEW to view the selected baby
unit temporarily in Single CAM mode. It
returns to Split mode after 10 seconds.
Note
• The parent unit is muted while in Split mode.
1
2
Install the parent unit battery
The parent unit runs on rechargeable battery or AC power. To continuously monitor your
baby, keep the parent unit connected to AC power. With the battery alone, the parent unit can
cordlessly run for approximately 2.5 hours.
NOTESNOTE
• Use only the battery supplied with this product.
• If the parent unit will not be used for a long time, disconnect and remove the battery to prevent possible leakage.
Replace the battery
To replace the battery, press down on the battery compartment cover and pull it out, then
follow the steps above to install the battery.
Connect the baby monitor
NOTESNOTE
• Use only the power adapters supplied with this product.
• Make sure the baby monitor is not connected to a switch controlled electric outlet.
• Connect the power adapters in a vertical or floor mount position only. The adapters’ prongs are not
designed to hold the weight of baby monitor, so do not connect them to any ceiling, under-the-table,
or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets.
• Make sure the parent unit, the baby unit and the power adapter cords are out of reach of children.
Charge the parent unit battery
When you have connected the parent unit and installed its battery for the first time or after
power outage, the parent unit powers on automatically. The battery icon indicates the
battery status (see the following table).
Notes
• The parent unit battery is fully charged after 3 hours of continuous charging.
• It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time,
turn the parent unit off while charging.
• The standby time varies depending on the sensitivity level you set, your actual use and the age of the battery.
Battery indicators Battery status Action
The battery icon is off and
displays.
No battery is installed but
operates using AC power,
or the battery has been
installed incorrectly.
Install the parent unit battery.
Charge without interruption (at
least 30 minutes).
The screen displays Battery
low at Parent Unit and .
The light flashes.
The battery has very little
charge and may be used
for only a short time.
Charge
without interruption
(about
30 minutes).
The battery icon becomes
solid .
The battery is fully charged. To keep the battery charged, connect
it to AC power when not in use.
THIS SIDE UP
1
2
3
Press down
on the battery
compartment
cover to pull
it out.
Make sure the
label THIS SIDE
UP is facing up
while inserting
the battery.
S trangulation
Haza rd
Keep this cord out of rea ch of chi ldren. The cord needs to be at le ast three feet
away from the c hild a t all times. D o not
use with an e xtension c ord. D o not remove this tag.
Éloignez ce cordon de s enfants. Le cordon doit se trouver à a u moins trois
pieds d’un enfant et ce, en tout temps. N’utili sez pa s de rallonge . N e retirez pas
cette étiquette.
Mantenga e ste cabl e fue ra de la alc anc e
de los niños. Este c able debe estar por lo menos tres pies fuera de la al ca nce del ni ño en todo momento. N o l o use
con una extensión inal ámbric a. No quite
esta etiqueta.
Risque
d’é trangle me nt
Rie s g o de
e s tra ngulación
BM5100-BEAR
Video Monitor
≥
1 metre
63ē
When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and
injury, including the following:
1. Follow all warnings and instructions marked on the product.
2. Adult setup is required.
3. This product is intended as an aid. It is not a substitute for responsible and proper adult supervision and should not be used as such.
4. This product is not intended for use as a medical monitor.
5. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or
swimming pool, or in a wet basement or shower.
6. CAUTION: Use only the batteries indicated in this manual. There may be a risk of explosion if a wrong type of battery is used for the
parent unit. Use only the supplied rechargeable battery or the parent unit. Do not dispose of batteries in a fire. They may explode.
7. Use only the adaptors included with this product. Incorrect adaptor polarity or voltage can seriously damage the
product.
Baby unit power adaptor: Output: 5V DC 1000mA; Parent unit power adaptor: Output: 5V DC 1000mA.
8. The power adaptors are intended to be correctly oriented in a vertical or floor mount position. The prongs are not
designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.
9. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible.
10. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
11. Unplug the power cords before replacing batteries.
12. Do not cut off the power adaptors to replace them with other plugs, as this causes a hazardous situation.
13. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped.
14. This product should be operated only from the type of power source indicated on the marking label. If you are not sure
of the type of power supply in your home, consult your dealer or local power company.
15. Do not overload wall outlets or use an extension cord.
16. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.
17. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back
or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be
blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or
over a radiator or heat register.
18. Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or
create a short circuit. Never spill liquid of any kind on the product.
19. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility.
Opening or removing parts of the product other than specified access doors may expose you to dangerous voltages
or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.
20. You should test the sound reception every time you turn on the units or move one of the components.
21. Periodically examine all components for damage.
22. Be aware of possible loss of privacy while using public airwaves. Conversations may be picked up by other nursery
monitors, cordless phones, scanners, etc.
23. Children should be supervised to ensure that they do not play with the product.
24. The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance
by a person responsible for their safety.
SAVE THESE INSTRUCTIONS
Cautions
1. Use and store the product at a temperature between 0oC and 40oC.
2. Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source.
3. Batteries should not be exposed to excessive heat such as bright sunshine or fire.
4. Make sure the baby unit(s) and the adaptor cord(s) are always out of reach of the baby, at least 1 metre away from
the baby or cot, to avoid a possible strangulation hazard.
5. Never place the baby unit(s) inside the baby’s cot or playpen. Never cover the baby unit(s) or parent unit with anything
such as a towel or a blanket.
6. Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as
far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room
monitors, televisions, personal computers, kitchen appliances and cordless telephones.
Important safety instructions
Specifications are subject to change without notice.
© 2019 VTech Telecommunications Ltd.
All rights reserved. 08/19. BM5100-BEAR_AU_CIB_V1
St ra ngulation
Haz a rd
Kee p thi s c o rd ou t o f re ach o f c h il dThe c ord n e ed s to b e at l east thr ee feaway from the c hi ld at all ti me s. Do n ou se with an exte nsio n c o rd. Do n ot
remo ve th is tag.
Éloigne z c e c ord on d e s e nfants. L e c o rdo n do it se tro uver à au m o in s tropied s d ’u n e nfant e t c e , e n to ut te m
N’util ise z pas de rallon ge . N e re tire z pc ette éti qu e tte .
Mantenga este cable fu era de la alcanc e
de los n iñ os. Este cabl e debe estar por lo m enos tres pies fu era de la alc anc e del ni ñ o en to do mo m ento. No lo use
con u na extensión in alámbr ic a. No qu iesta etiqueta.
Ris que
d’ét ra ngle me nt
Ries go de
e s tra ngula ción
63
℉
63
℉
> 1metre
> 1metre
< 1metre
> 1metre
63ē
63ē
Press VIEW
Menu tree
Status icons
Connection status
displays when strong signal strength is detected between the baby unit and the
parent unit.
or displays when moderate or low signal strength is detected between the baby
unit and the parent unit.
displays when the link between the baby unit and the parent unit is lost.
Lullaby
Displays when the baby unit being viewed is playing lullabies or soothing sounds.
Current view status
Displays the baby unit number of the baby unit that is being viewed.
Night vision
Displays when the baby unit being viewed has activated the night vision feature.
Talkback
Displays when you are hold the key on the parent unit.TALK
or
Real-time temperature
Displays the real-time temperature detected by the baby unit in Fahrenheit (oF) or
Celsius (oC)
(e.g. 57 oF 14 or oC).
Temperature alert tone
Displays when the temperature alert tone is on.
Mute alert
Displays when the parent unit is talking to the baby unit.
Vibration alert
Displays when the vibration is set to on.
9-level sound indicator
(1 to 3 bars) indicates low sound level detected by the baby unit.
(4 to 6 bars) indicates moderate sound level detected by the baby unit.
(7 to 9 bars) indicates high sound level detected by the baby unit (e.g. baby
crying loudly).
Zoom
Displays when the current image on the parent unit has zoomed in.
Battery status
animates when the battery is charging.
displays solid when the battery is fully charged.
displays when the battery is low and needs charging.
AC power without battery
Displays when the parent unit is connected to AC power without the battery.
Below are the questions most frequently asked about the baby monitor.
Why does the baby monitor not
respond normally? Try the following (in the order listed) for common cure:
1. Disconnect the power to the baby units and the parent unit.
2. Remove the batteries in the parent unit. Then, install the batteries again.
3. Wait a few seconds before connecting power back to the baby units and the parent unit.
4. Turn on the baby units and the parent unit.
5. Wait for the parent unit to synchronize with the baby units. Allow up to one minute for this to take place.
Why don’t the
power-on light of the baby unit and
parent unit go on when I switch on
the units?
Perhaps the parent unit is not connected to the power. Insert the appliance plug into the parent unit and put the adapter in a wall socket.
Then, press and hold to switch on the parent unit and to establish connection with the baby unit.POWER
Perhaps the baby unit is not connected to the power. Insert the appliance plug into the baby unit and put the adapter in a wall socket. Then,
slide the switch to ON/OFF ON to switch on the baby unit and to establish connection with the parent unit.
Why doesn’t my parent unit charge
while connected to AC power? Make sure the power is not controlled by a wall switch.
Make sure the battery is correctly installed in your parent unit.
You may have used the battery for a long time. Replace a new battery.
Why is my screen in black and white? The screen is in black and white during night-time or in a dark room when the night vision feature is activated. This is normal.
Why do I get glare or blurry display on
my screen when viewing my baby at
night?
During night-time or in a dark room, the surroundings and other interfering factors, like lightings, objects, colors and backgrounds may affect
the image quality on your parent unit screen. Adjust the baby unit’s angle or place the baby unit at a higher level to prevent glare and blurry
display.
Why does the baby monitor produce
a high-pitched noise? The parent unit and baby units may be too close to each other.
• Move the parent unit away from the baby units until the noise stops; OR
• Turn down the volume of your parent unit.
Why does the parent unit beep? The baby units may be out of range. Move the parent unit closer to the baby units (but not less than 1 metre).
The parent unit may not have enough charge for the parent unit to perform normally. Charge the battery in the parent unit for up to 3 hours.
If your parent unit is in mode, some of your baby units may detect sounds.Split
The temperature of your baby’s room may be too high or too low.
Why does the parent unit beep/
vibrate frequently in mode?Split You may have set the VOX sensitivity level to Highest when the sound alert (and vibration) feature is turned on. The parent unit notifies you
of all sounds including background noise with beeps (and vibration). Adjust the VOX sensitivity to a lower level.
Why does the parent unit react too
quickly to other sounds? The baby unit also picks up other sounds than those of your baby. Adjust the VOX sensitivity level to a lower level or lower the parent unit
speaker volume.
Why don’t I hear a sound/Why can’t I
hear my baby cry? The parent unit speaker volume may be too low. Press to increase the volume.
You may have set a low VOX sensitivity level. See Adjust the sound sensitivity of the baby unit to set to a higher level.
Why can’t I establish a connection?
Why is the connection lost every
now and then? Why are there sound
interruptions?
The baby units may be out of range. Move the parent unit closer to the baby units (but not less than 1 metre).
Other electronic and wireless products may cause interference with your baby monitor. Try installing your baby monitor as far away from
these devices as possible.
If you power on only one baby unit, your parent unit may display and No link to CAM #, and the LED light flashes. Press to switch LINK VIEW
to the baby unit you have powered on.
Frequently asked questions
When you are not going to use the baby monitor for some time, remove the rechargeable battery from the parent unit. Store the parent unit, the baby unit and the
adapters in a cool and dry place.
Storage
Parent unit icons
1 LED lights
Indicate the different statuses of the
parent unit. For details, refer to Parent
unit lights.
2LCD display
3VOL
4 VOL
5 Zoom
• Press to zoom in or out.
6VIEW / LCD ON/OFF
7Microphone
8POWER
9TALK
• Press and hold to talk e selected to th
baby unit.
10
• While in a menu, press to return to
the main menu or idle screen.
• While viewing zoomed image, press
and hold to move the zoomed image
leftward.
• While in Split mode, press to move
the selection box leftward.
11
• While in a menu, press to scroll up.
• While viewing zoomed image, press
and hold to move the zoomed image
upward.
12
• While in a menu, press to choose an
item.
• While viewing zoomed image, press
and hold to move the zoomed image
rightward.
• While in Split mode, press to move
the selection box rightward.
13 MENU/SELECT
• Press to enter the menu.
• While in a menu, press to choose an
item, or save a setting.
14
• While in a menu, press to scroll down.
• While viewing zoomed image, press
and hold to move the zoomed image
downward.
15 Antenna
16 Stand
17 Speaker
18 Power jack
19 Battery compartment cover
1Light sensor
2Infrared LEDs
3Camera
4Power light
• is ON when the baby unit is turned
on and is paired to the parent unit.
• Flashes when the baby unit is not
being viewed; or when the link to
the parent unit is lost.
5/VOL/
• Press to adjust the baby unit
speaker volume. It determines the
lullaby volume and talkback volume
transmitted from the parent unit.
6 Play/Stop
• Press to play or stop lullabies on the
baby unit.
7Microphone
8 Skip
• Press to play the next lullaby.
9ON/OFF switch
• Slide to turn on or off the baby unit.
10 Speaker
11 Temperature sensor
12 PAIR
• Press and hold to pair to the parent
unit when a desired baby unit slot is
chosen at the parent unit.
13 Threaded socket
• For wall mount installation use.
14 Power jack
Baby unit overview
Main menu icons
Brightness
You can adjust the LCD brightness.
Sensitivity (VOX setting)
With this feature, you can choose to hear sounds from the baby unit all the time, or
to hear sounds that exceed a certain level. You can use the parent unit to adjust the
microphone sensitivity of your baby unit. The higher the sensitivity level, the more
sensitive the baby unit is in detecting sounds for transmitting to the parent unit.
Temperature
You can turn on the temperature alert tone so that the parent unit beeps
whenever the room temperature detected by the baby unit falls outside of the
desired temperature range.
You can choose to display the temperature in Fahrenheit (oF) or Celsius (oC), or set the
maximum/minimum temperature limit for alerts.
Lullaby
You can choose a lullaby or soothing sound to comfort your baby.
Camera
You can adjust the volume of baby unit which determines the lullaby volume and
talkback volume transmitted from parent unit.
Vibration
You can turn on the vibration alert so that the parent unit vibrates when it receives
Low battery tone, No link alert, or Sound alert Temperature alert tone after
turning on the respective alert tones.
Alert Tone setting
You can set the parent unit to beep when
the parent unit operates in low battery condition; or
the link between the parent unit and the baby unit is lost.
Sleep timer
You can set the auto screen-off timer so that the LCD will turn off automatically
when the parent unit does not detect sound for the period of time you set (1, 2 or
3 minutes).
Exit
You can select this option to exit the menu.
Warning icons and messages
The selected baby unit is out of range or is turned off.
The battery level of the parent unit is very low and needs to be
recharged.
The sound level exceeds the threshold at CAM # in Split mode.
or
The temperature detected by the baby unit is higher/lower than the
desired temperature alert range.
The parent unit is searching for the baby unit.
Parent unit overview Parent unit lights
LINK • On when the parent unit is linked to the baby unit.
• Flashes when the link to the baby unit being viewed in or Single CAM Patrol mode
is lost; or when the link to at least one baby unit being viewed in mode is lost.Split
• On when the parent unit is connected to AC power, or the battery is charging.
• Flashes when the parent unit battery is low and needs charging.
• Off when the parent unit is disconnected from AC power.
It turns on:
• When the parent unit is talking to the baby unit; or
• When the parent unit is in Split mode.
TALK • On when the parent unit is talking to the baby unit.
Main
Menu
Brighteness
Sensitivity
(VOX
setting)
Tempera-
ture
Lullaby Camera Vibration Alert Tone Sleep
timer
Exit
Sub
Menu
Level 1 -5 Level 1 -5
Format
Maximum
Minimum
Set alert
Auto timer
Play melodies
Play soothing
sound
Format
Delete
camera
Add
camera
Volume
on camera
On
Off
No link
alert
Low battery
alert
1 minute
2 minutes
3 minutes
Off
Frequency control Crystal controlled PLL synthesizer
Transmit frequency Baby unit: 2406 - 2475 MHz
Parent unit: 2405 - 2475 MHz
Channels 32
LCD 5” Color LCD
(WQVGA 480x272 pixel)
Nominal effective range Actual operating range may vary according to environmental
conditions at the time of use.
Power requirements Parent unit: 3.7V Li-polymer battery
Baby unit power adapter: Output: 5V DC @ 1A
Parent unit power adapter: Output: 5V DC @ 1A
Technical specifications
Disposal of batteries and product
The crossed-out wheelie bin symbols on products and batteries, or on their respective
packaging, indicates they must not be disposed of in domestic waste as they contain
substances that can be damaging to the environment and human health.
The chemical symbols Hg, Cd or Pb, where marked, indicate that the battery contains
more than the specified value of mercury (Hg), cadmium (Cd) or lead (Pn) set out in
Battery Directive (2006/66/EC).
The solid bar indicates that the product was placed on the market after 13th August, 2005.
Help protect the environment by disposing of your product or batteries responsibly.
IMPORTANT
Please retain this booklet with your sales receipt as proof of the date of purchase.
Customer Service
If you require assistance in operating this product, please call the TecHelp Information Line on
1300 369 193 or contact VTech by e-mail at: tcpsupport_au@vtech.com.
Voluntary Product Enquiry
In addition to your Statutory Rights and subject to the conditions below, VTech warrants that this product will
be free from any defect in materials or workmanship under conditions of normal use for a period of 24 months
from date of purchase.
VTech does not warrant that the product will be free from defects if defects are caused by an accident, misuse,
abuse, improper installation or operation, vermin infestations, lack of reasonable care, unauthorised modification,
loss of parts, tampering or attempted repair by a person not authorised by VTech; or where the product has been
damaged by lightning or a mains power surge.To make a claim under this Voluntary Product Warranty you must call
the TecHelp Information Line on 1300 369 193 or contact VTech by e-mail at: tcpsupport_au@vtech.com where a
Customer Service Representative will inform you of the product return process. You will need to ensure that:
• You provide proof of purchase;
• Your product is suitably packaged (original packaging is not required); and
• You have included all components from the original purchase.
For your records
Date of purchase:
Place of purchase:
Serial number:
For Voluntary Product Warranty purposes, proof of purchase is required so please keep your receipt.
The benefits conferred by this Voluntary Product Warranty are in addition to other rights and remedies that are
available to you under law, which cannot be excluded. The processes for this Voluntary Product Warranty in no way
limit your rights which arise as a result of your Statutory Rights.
This Voluntary Product Warranty is given by:
VTech Telecommunications (Australia) Pty Ltd ABN 70 136 672 627
Address: 24 Gilby Road, Mount Waverley 3149
IMPORTANT NOTE: THIS IS NOT A PRODUCT RETURN OR SERVICE ADDRESS – PLEASE CONTACT TECHELP BY PHONE
OR EMAIL FOR PRODUCT AND WARRANTY SUPPORT. NO LIABILITY WILL BE ACCEPTED BY VTECH FOR PRODUCTS
RETURNED TO THIS ADDRESS UNDER THIS VOLUNTARY PRODUCT WARRANTY.
Phone number: 1300 369 193
Email address: tcpsupport_au@vtech.com
Statutory Rights
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss
or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
Customer service and product warranty
The baby unit has infrared LEDs that allow you to see your baby clearly at night or in a dark
room. When the baby unit being viewed detects low light levels, the infrared LEDs are
switched on automatically. The images from the baby unit are in black and white, and
appears on the screen.
Notes
• It is normal if you see a short white glare on your parent unit screen as the baby unit is adapting
to the dark environment.
• When the infrared LEDs are on, the images are in black and white. This is normal.
Tip
• Depending on the surroundings and other interfering factors, like lightings, objects, colors and
backgrounds, the video quality may vary. Adjust the baby unit’s angle or place the baby unit at a
higher level to prevent glare and blurry display.
Night vision
To keep this product working well and looking good, follow these guidelines:
• Avoid putting it near heating appliances and devices that generate electrical noise (for example, motors or fluorescent lamps).
• DO NOT expose it to direct sunlight or moisture.
• Avoid dropping the product or treating it roughly.
• Clean with a soft cloth.
• DO NOT immerse the parent unit and the baby unit in water and do not clean them under the tap.
• DO NOT use cleaning spray or liquid cleaners.
• Make sure the baby unit and parent unit are dry before you connect them to the mains again.
General product care
Mount the baby unit (optional)
Align the wall mount bracket and
screws with the holes in the wall as
shown. Tighten the screw in the middle
hole first, so that the wall mount
bracket position is fixed. You can
tighten the other screw in the top hole.
OR
Place the wall mount bracket on a
wall and then use a pencil to mark the
top and the bottom holes as shown.
Remove the wall mount bracket and drill
two holes in the wall (7/32 inch drill bit).
Note
• Check for reception strength and camera
angle before drilling the holes.
If you drill the holes into a stud, go to
step 3.
-OR-
If you drill the holes into an object other
than a stud, insert the wall anchors into
the holes. Tap gently on the ends with a
hammer until the wall anchors are flush
with the wall.
Place the baby unit on the wall mount
bracket. Tighten the screw into the
threaded socket at the bottom to
secure the baby unit.
Insert the screws into the holes and tighten
the screws until only 1/4 inch of the screws
are exposed.
Place the baby unit on the wall mount
bracket. Tighten the screw into the threaded
socket at the bottom to secure the baby unit.
Align the holes on the wall mount bracket
with the screws on the wall, and slide the
wall mount bracket down until it locks into
place.
You can maximize your baby unit’s viewing angles by tilting the wall mount
bracket.
Hold the baby unit, and then rotate the knob in anticlockwise direction. This
will loosen the joint of the wall mount bracket. Tilt your baby unit up or down to
adjust to your preferred angle. Then, rotate the knob in clockwise direction to
tighten the joint and secure the angle.
Note
• The types of screws and anchors you need
depend on the composition of the wall.
d
e
f
g
a
b
c
h
i
j
k
n
l
m
2
1

Produktspezifikationen

Marke: Vtech
Kategorie: Babyphone
Modell: BM5100-Bear

Brauchst du Hilfe?

Wenn Sie Hilfe mit Vtech BM5100-Bear benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Babyphone Vtech

Vtech

Vtech Clear Sounds Deluxe Bedienungsanleitung

2 Oktober 2024
Vtech

Vtech Clear Sounds Bedienungsanleitung

12 September 2024
Vtech

Vtech RM5766HD Bedienungsanleitung

31 August 2024
Vtech

Vtech Bel & Tel Bedienungsanleitung

23 August 2024
Vtech

Vtech DM1111 Bedienungsanleitung

16 August 2024
Vtech

Vtech RM5762 Bedienungsanleitung

6 August 2024
Vtech

Vtech Peppa Pig Bedienungsanleitung

2 August 2024
Vtech

Vtech Safe & Sound VM341 Bedienungsanleitung

29 Juli 2024
Vtech

Vtech Sleepy Bear Bedienungsanleitung

28 Juli 2024
Vtech

Vtech VM333-2 Bedienungsanleitung

19 Juli 2024

Bedienungsanleitung Babyphone

Neueste Bedienungsanleitung für -Kategorien-

Alecto

Alecto DBX-72 ECO Bedienungsanleitung

9 Oktober 2024
Reer

Reer Neo 200 Bedienungsanleitung

8 Oktober 2024
Babymoov

Babymoov High Care A014009 Bedienungsanleitung

7 Oktober 2024
Topcom

Topcom KS-4241 Bedienungsanleitung

3 Oktober 2024
Lorex

Lorex BB1811 Bedienungsanleitung

2 Oktober 2024
Alecto

Alecto DVM-75C Bedienungsanleitung

2 Oktober 2024
TrueLife

TrueLife NannyCam V24 Pro Bedienungsanleitung

1 Oktober 2024
TrueLife

TrueLife NannyCam H32 Pro Bedienungsanleitung

1 Oktober 2024
Uniden

Uniden GC43W Bedienungsanleitung

30 September 2024
EMOS

EMOS H100BF-CE Bedienungsanleitung

29 September 2024