Vitek VTD-MD7CH Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Vitek VTD-MD7CH (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
VITEK
VTD-MD7CH
Vandal Resistant Mini Dome
Camera with 700 TVL
FEATURES:
• 1/3” Sony® Super HAD II CCD
• Sony Effio-E Digital Signal Processor (DSP)
• 700 TV Lines of Resolution
• 2.8mm Lens Included (3.6, 6, 8, 12 and 16mm also
available)
• Sensitivity of 0.0003Lux
• 2D-DNR - Two Dimensional Motion Adaptive Noise
Reduction
• Can be Semi-Flush or Surface Mounted
• IP-66 Rated Weather Resistant Aluminum Enclosure w/
Polished Chrome Finish
• 12VDC Operation
1
INSTALLATION
1) Align the camera unit with the
surface of the ceiling, make marks
on the ceiling in the places where
the screw holes are to be drilled,
and then drill the three holes.
2) Cut a hole (diameter:50mm) in the
ceiling for routing the cables.
3) Pass the power cable (B) and video
cable (A) from the camera unit
through the cable hole in the ceiling.
4) Align the three screw holes in the
camera unit (C) with the screw holes
in the ceiling, and then secure the
camera in place by tightening the
three tapping screws.
5) Use the supplied the four screws (E)
to secure the middle base (D) to the
bottom base (C)
6) Tighten the guide ring (G), then
adjustment the camera (F).
7) Attach the bubble (H) to the middle
base (D).
8) Attach the top cover (I) to the middle
base (D).
9) Use the supplied star-shaded
L-wrench to tighten the set screw on
the top cover.
Open Close
2
SPECIFICATIONS
VTD-MD7CH
Image Device
Resolution
Effective Pixels
Minimum Illumination
Included Lens
Day/Night
Noise Reduction
Synchronization
S/N Ratio
Video Output
Electronic Iris
Construction
Water Resistance
Power Source
Power Consumption
Operating condition
Dimensions
Weight
1/3” Sony® Super HAD II CCD w/Effio-E DSP (960H)
700TVL
976(H) x 494(V)
0.0003Lux @ F1.2
2.8mm (3.6, 6, 8, 12 and 16mm also available)
Auto
2D-DNR
Internal
More than 50dB
VBS 1Vpp +/-10%, 75ohm
1/60 ~ 1/100,000sec
Aluminum Housing with Polished Chrome Finish
IP-66
12VDC
100mA
14F ~ 122F (-10C ~ +50C) / 95% RH Max
3.15” x 1.69”/2.47” (80mm x 42.8mm/62.8mm)
14.11 Oz. (400g)


Produktspezifikationen

Marke: Vitek
Kategorie: Nicht kategorisiert
Modell: VTD-MD7CH

Brauchst du Hilfe?

Wenn Sie Hilfe mit Vitek VTD-MD7CH benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Vitek

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-